New Buck Corporation 384 manual Freestanding Pedestal Or Legs Installation

Page 33

FREESTANDING PEDESTAL OR LEGS

FREESTANDING PEDESTAL OR LEGS

INSTALLATION

1.The Model 384 can be mounted as free standing with either a pedestal or Queen Anne legs.

A.To mount the pedestal Part No.(FA P14) to the heater lay the heater on its back (use a drop-cloth to protect the back of the heater and the surface of your flooring). Place pedestal against bottom of heater. Center pedestal from left to right and from front to rear. Mark the holes on the angle on the top of the pedestal. Lay the pedestal aside. Drill the marks. Replace the pedestal and secure with the provided screws.

B.For legs kit Part No.(FA FS384) place heater on its back. Your heater is equipped with four leg mounting nuts.

Place a leg at each nut and secure leg with the bolts provided.

The legs are equipped with leveling bolts needed for leveling adjustments.

2.Stand heater to the upright position. Place heater in the desired location. At this point you may want to secure the pedestal to the floor with screws or an “ell” bracket.

3.Hook up gas supply line. Check for leaks with mild soapy water. See page 5 Installation Clearances and Gas Connection.

Page 29

Image 33

Contents VENT-FREE MODELManufacturer NEW BUCK CORPORATION P.O. Box 8000 Highway 226 South Spruce Pine, NCPage TABLE OF CONTENTS Page SECTION I SAFETY INFORMATION WARNINGS 6. What To Do IF You Smell Gas Shut off gas supply 32. This appliance is intended for supplemental heating FIREPLACE PREPARATION SECTIONINSTALLATION AND CLEARANCES GAS CONNECTIONFLAME Page “MILLIVOLT ONLY” GAS PRESSURE CHECK LIGHTING INSTRUCTION MODULATING OR MANUAL VALVE SIT FOR YOUR SAFETY READ BEFORE LIGHTINGLIGHTING INSTRUCTION 12. Close access panel door 13. Turn on all electrical power to the applianceto “ON” position. Continue to turn the to your desired setting THERMOSTAT CONTROL OPERATION MANUAL LIGHTING PROCEDUREFOR YOUR SAFETY READ BEFORE LIGHTING LIGHTING INSTRUCTIONS SIT-MILLIVOLT VALVEOPERATING INSTRUCTIONS Page Page MANUAL LIGHTING PROCEDURE WHEN USED AS A HEATING APPLIANCE HEAT OUTPUT FLAME CHECKCR 3329 LOG SET WIRING DIAGRAM NOTE #PE SBR084 Blower Motor Rating 120 volts/60HZ/1.1 Amps SECTION INSTALLATION MODEL 384 FP IN SOLID FUEL BURNING FIREPLACES Trim KitCEILING Also provide adequate clearances around air openings OPTIONAL WOODEN SURROUND KIT#PAKDM384 SECTION INSTALLATION OF MODEL 384 WS WITHSTEP 7 Remove cloth or blanket from underneath stove CHOOSING THE LOCATION FOR YOUR FIREPLACE SECTION ZERO CLEARANCE INSTALLATION OF MODEL 384 ZCGAS LINE DRAFTS“Follow the instructions given in the diagrams below exactly” ZERO CLEARANCE STANDOFFS ASSEMBLYTop Standoff 2 per unit 12.50” Front Of Top Trim PanelFIREPLACE CLEARANCES INSTALLING THE FIREBOXInstall the Firebox Framing the FireboxCLEARANCES FINISHING YOUR FIREPLACESECTION MODEL 384 FS FREESTANDING INSTALLATION FREESTANDING PEDESTAL OR LEGS INSTALLATION CAUTION READ ENTIRE MANUAL BEFORE INSTALLING HEATER SECTION MODEL ALCOVE INSTALLATIONSECTION PRODUCING ADEQUATE VENTILATION DETERMINING FRESH-AIR FLOW FOR HEATER LOCATIONThis section is for residential or manufactured mobile installation 1. Determine the volume of the space length x width x height VENTILATION AIR FROM INSIDE BUILDING SECTION VENTILATION AIRVentilation Air From Outdoors VENTILATION AIR FROM OUTDOORSSECTION AFTER MARKET MOBILE HOME INSTALLATION CLEANING IMPORTANT SAFEGUARDSOBSERVED Air in gas lines when OBSERVED OBSERVED SERVICING REPAIR PARTSSIT MODULATING OR MANUAL VALVE REPLACEMENT PARTSKEY# PART DESCRIPTIONPILOT 1719SIT MILLIVOLT VALVE REPLACEMENT PARTSSIT MILLIVOLT REPLACEMENT PARTS FOR EMBER STOVE BASE ESB 10 one is not available, you may contact SIT MILLIVOLTPage NEW BUCK CORPORATION LIMITED WARRANTY VENT-FREE GAS LOG HEATERPage