New Buck Corporation 384 manual Installation And Clearances, Gas Connection, Flame

Page 9

INSTALLATION AND CLEARANCES

INSTALLATION AND CLEARANCES

To ensure a safe installation into a masonry or factory built fireplace, the following instructions must be carefully followed:

(1) Sidewall Clearances:

Clearance from the side of the fireplace opening to any adjacent combustible wall should not be less than: right side 7", left side 7".

(2) Ceiling Clearances:

The ceiling height should not be less than 26" from the top of the fireplace opening.

(3) Mantel Clearances:

Clearances from top of heater to mantel or mantel supports should not be less than 20".

NOTE: See the following sections for installation options: Section III, page 20, Installation In A Solid- Fuel Burning Fireplace, and Section IV, page 22, Installation With Optional Wooden Mantel, and Section V, page 24, Zero Clearance Installation.

GAS CONNECTION

Check gas type. Use only the type of gas indicated on the valve rating plate. If the type of gas listed on the plate is not your type of gas supply, DO NOT INSTALL. Contact your dealer for proper model. Always use an external regulator for all LP heaters to reduce the supply tank pressure to a maximum of 13" W.C. This is in addition to the regulator furnished with the heater.

The normal gas connection is 3/8” N.P.T. made at the left rear (facing the front of the appliance) of the appliance.

NOTE: The connecting pipe must be internally tinned copper tubing for use with natural gas. Test for leaks using a solution of soap and water after completing the connection. DO NOT USE OPEN

FLAME.

NOTE: “If the factory-built fireplace has no gas access hole(s) provided, an access hole of 1.5 inch (37.5mm) diameter or less may be drilled through the lower sides or bottom of the fire box in a proper workmanlike manner. This access hole must be plugged with non-combustible insulation after the gas supply line has been installed.”

Page 5

Image 9

Contents VENT-FREE MODELManufacturer NEW BUCK CORPORATION P.O. Box 8000 Highway 226 South Spruce Pine, NCPage TABLE OF CONTENTS Page SECTION I SAFETY INFORMATION WARNINGS 6. What To Do IF You Smell Gas Shut off gas supply 32. This appliance is intended for supplemental heating FIREPLACE PREPARATION SECTIONINSTALLATION AND CLEARANCES GAS CONNECTIONFLAME Page “MILLIVOLT ONLY” GAS PRESSURE CHECK LIGHTING INSTRUCTION MODULATING OR MANUAL VALVE SIT FOR YOUR SAFETY READ BEFORE LIGHTINGLIGHTING INSTRUCTION 12. Close access panel door 13. Turn on all electrical power to the applianceto “ON” position. Continue to turn the to your desired setting THERMOSTAT CONTROL OPERATION MANUAL LIGHTING PROCEDUREFOR YOUR SAFETY READ BEFORE LIGHTING LIGHTING INSTRUCTIONS SIT-MILLIVOLT VALVEOPERATING INSTRUCTIONS Page Page MANUAL LIGHTING PROCEDURE WHEN USED AS A HEATING APPLIANCE HEAT OUTPUT FLAME CHECKCR 3329 LOG SET WIRING DIAGRAM NOTE #PE SBR084 Blower Motor Rating 120 volts/60HZ/1.1 Amps SECTION INSTALLATION MODEL 384 FP IN SOLID FUEL BURNING FIREPLACES Trim KitCEILING Also provide adequate clearances around air openings OPTIONAL WOODEN SURROUND KIT#PAKDM384 SECTION INSTALLATION OF MODEL 384 WS WITHSTEP 7 Remove cloth or blanket from underneath stove CHOOSING THE LOCATION FOR YOUR FIREPLACE SECTION ZERO CLEARANCE INSTALLATION OF MODEL 384 ZCGAS LINE DRAFTS“Follow the instructions given in the diagrams below exactly” ZERO CLEARANCE STANDOFFS ASSEMBLYTop Standoff 2 per unit 12.50” Front Of Top Trim PanelFIREPLACE CLEARANCES INSTALLING THE FIREBOXInstall the Firebox Framing the FireboxCLEARANCES FINISHING YOUR FIREPLACESECTION MODEL 384 FS FREESTANDING INSTALLATION FREESTANDING PEDESTAL OR LEGS INSTALLATION CAUTION READ ENTIRE MANUAL BEFORE INSTALLING HEATER SECTION MODEL ALCOVE INSTALLATIONSECTION PRODUCING ADEQUATE VENTILATION DETERMINING FRESH-AIR FLOW FOR HEATER LOCATIONThis section is for residential or manufactured mobile installation 1. Determine the volume of the space length x width x height VENTILATION AIR FROM INSIDE BUILDING SECTION VENTILATION AIRVentilation Air From Outdoors VENTILATION AIR FROM OUTDOORSSECTION AFTER MARKET MOBILE HOME INSTALLATION CLEANING IMPORTANT SAFEGUARDSOBSERVED Air in gas lines when OBSERVED OBSERVED SERVICING REPAIR PARTSSIT MODULATING OR MANUAL VALVE REPLACEMENT PARTSKEY# PART DESCRIPTIONPILOT 1719SIT MILLIVOLT VALVE REPLACEMENT PARTSSIT MILLIVOLT REPLACEMENT PARTS FOR EMBER STOVE BASE ESB 10 one is not available, you may contact SIT MILLIVOLTPage NEW BUCK CORPORATION LIMITED WARRANTY VENT-FREE GAS LOG HEATERPage