New Buck Corporation manual FREESTANDING INSTALLATION MODEL 32 FS, Wall

Page 10
FREESTANDING INSTALLATION

FREESTANDING INSTALLATION

MODEL 32 (FS)

1. Determine the exact location of your gas heater.

NOTE: Due to high temperatures, this heater should be located out of traffic areas and away from furniture and draperies.

NOTE: For safe installation the minimum clearances must be met. See Figure 2. For floor protector, see last paragraph, page 8.

NOTE: Clearance form top of appliance to ceil- ing is 42”. (Not shown in figure 2)

 

WALL

 

 

NOTE:

 

 

DIMENSIONS SHOWN ARE

 

 

MINIMUM CLEARANCE TO

4"

5"

COMBUSTIBLE WALL.

 

 

 

 

STOVE

 

 

Figure 2

WALL

4"

4"

NOTE: See page 17 for “Gas Connection” and page 18 for “Pressure Check”.

2.Check gas type. Use only the type of gas indicated on the valve rating plate. If the type of gas listed on the plate is not your type of gas supply, DO NOT INSTALL. Contact your dealer for proper model. Position logs as shown on page 16. Position screen before leaving heater unattended.

NOTE: When the appliance is installed directly on carpeting, tile or other combustible material, other than wood flooring, the appliance shall be installed on a metal or wood panel extending the full width and depth of the appliance.

Optional Pedestal (Part#FAP11) Instructions: Lay the heater on its back (use a drop-cloth to protect the back of the heater and the surface of your flooring). Place pedestal against the bottom of the heater. Center pedestal from left to right and from front to rear. Mark the holes on the angle of the top of the

pedestal onto the bottom of the heater. Lay the pedestal aside. Drill the marks made onto the heater with a 1/8” bite (not pro- vided). Replace the pedestal and secure with the screws pro- vided. Next stand the heater to the upright position. Place the heater in the desired location following the clearances above in figure 2. Note: At this point you may need to secure the pedes- tal to the floor with screws or an “ell” bracket (not provided) for safety concerns. Next hook up the gas supply line follow- ing the instructions in this manual completely.

Page 8

Page 9 Page 11
Image 10
Page 9 Page 11
Contents OPTIONAL WOODEN SURROUND MODELFREESTANDING FIREPLACE OR WITH AN VENT-FREEPage TABLE OF CONTENTS Page SECTION SAFETY INFORMATION WARNINGS Do not try to light any appliance psi 3.5 kPa WALL FigureCEILING LEFT SIDE7.Place logs on the burner base as shown on page WALL FREESTANDING INSTALLATION MODEL 32 FSWALL FOR YOUR SAFETY ALCOVE INSTALLATIONWALL WITH OPTIONAL WOODEN SURROUNDKIT#PA-KDM32 INSTALLATION OF MODEL 32 WSWS ASSEMBLY INSTRUCTIONS Installation” for minimum clearancesOR AFTER-MARKETMOBILE HOMES INSTALLATION IN RESIDENTIALNOTE: See “Producing Adequate Ventilation” page PRODUCING ADEQUATE VENTILATION DETERMINING FRESH-AIRFLOW FOR HEATER LOCATIONVent-freeheater VENTILATION AIR VENTILATION AIR FROM INSIDE BUILDINGVENTILATION AIR FROM OUTDOORS TOP LEFT PREPARING LOG KITTOP RIGHT REAR LOG FRONT LOGGAS CONNECTION FLAMEGAS PRESSURE CHECK LIGHTING INSTRUCTIONS MILLIVOLT VALVE ITT FOR YOUR SAFETY, READ BEFORE LIGHTINGWHAT TO DO IF YOU SMELL GAS LIGHTING INSTRUCTIONS IGNITOR ELECTRODE TO TURN OFF GAS TO APPLIANCEPILOT BURNER MANUAL LIGHTING PROCEDURE THERMOSTAT CONTROL OPERATIONLIGHTING INSTRUCTION MODULATING VALVE SIT FOR YOUR SAFETY READ BEFORE LIGHTINGOR MANUAL VALVE SIT LIGHTING INSTRUCTION 13.Turn on all electrical power to the appliance 12.Close access panel doorPage THERMOSTAT CONTROL OPERATION MANUAL LIGHTING PROCEDURE15seconds FLAME CHECK FLAMEWIRING DIAGRAM IMPORTANT SAFEGUARDS CLEANINGTROUBLE SHOOTING Air in gas lines when OBSERVED OBSERVED REPAIR PARTS SERVICINGPART DESCRIPTION REPLACEMENT PARTSKEY# PART NUMBERITTGENERAL CONTROLS PART DESCRIPTION REPLACEMENT PARTSKEY# PART NUMBERPage 5 6 13PILOT LIMITED WARRANTY MODEL FP-32 NEW BUCK CORPORATIONPage
Top Page Image Contents