Heat & Glo LifeStyle EXCLAIM-36H-C, EXCLAIM-36T-C Clearances, Failure to comply may cause ﬁre

Page 10

B. Clearances

WARNING

Fire Risk

• Comply with all minimum clearances to combustibles as speciﬁed.

Failure to comply may cause ﬁre.

Storm Collar

Roof Flashing

2 in. min.

(51 mm)

(attic)

2 in. min. (51 mm)

Attic

Insulation

Shield

Ceiling Firestop

	(ceiling)
2 in. min.	2 in. min.
(51 mm)	(51 mm)
Ceiling Firestop	Offset/Return with
	hanger straps
	(ceiling)

2 in. min.

(51 mm)

0 in. to level of standoffs

2 in. min. Must have 2 in. (51 mm)

(51 mm) minimum clearance to header

	1 in. (25 mm) to back
	of appliance
0 in.	1 in. (25 mm) to side of appliance
0 in.	(except at nailing flanges where it is 1/2 in. (13 mm))
to floor

Figure 3.2 Clearances to Combustible Materials

Note: Chimney air kit is not shown, but required in Canada.

10	Heat & Glo • EXCLAIM-36C Woodburning Fireplace • 4013-093 Rev G • 08/06

Image 10

Contents EXCLAIM-36H-C EXCLAIM-36T-C Fire RiskGrate Listing Label Information/LocationNumber Table of Contents Appliance Certiﬁcation Listing and Code ApprovalsNot intended for use as a primary heat source Negative Pressure Design and Installation ConsiderationsGetting Started Asphyxiation RiskMarginal Location Typical Fireplace System Typical Fireplace SystemInspect Fireplace and Components Tools and Supplies NeededFire Risk Explosion Risk Framing and Clearances Selecting Fireplace LocationClearances Failure to comply may cause ﬁreSidewalls/Surrounds Frame the FireplaceConstruct the Chase Chimney RequirementsFire Risk Sharp Edges Asphyxiation Risk Installation of FireplaceInstall the Outside Air Kit Risk of Smoke SpillageFt min. from top of uppermost chimney section to air inlet Place the Protective Metal Hearth Strips Secure the FireplacePosition the Fireplace Level the FireplaceChimney Assembly Height of Chimney Components Using Offsets/Returns ¨ TableInstall the Ceiling Firestops Assemble the Chimney SectionsDouble-check the Chimney Assembly Install the Attic Insulation ShieldSecure the Chimney Complete the Enclosure Chimney TerminationInstall the Chimney Air Kit required in Canada Install the Termination CapChase Top Installing an ST475 Square Termination Cap Gas Log/Lighter Provisions AccessoriesGas Code, Ansi Z223.1 Finishing Hearth ExtensionRaised Hearth Extension Glass Doors Finishing MaterialMantel Combustible MaterialOperating Instructions General InformationFlue Damper Outside AirClear Space Near the Fireplace FirescreenFirewood GrateWood Fuel MoistureStarting a Fire Troubleshooting Understanding Vent ProblemsSolutions Diagnostics and Problem SolvingDiagnostic Questions Can’t get a good ﬁre going. What am I doing wrong?ﬁreplace burns the wood too fast. What can I do? Disposal of Ashes Maintenance and Servicing the FireplaceChimney Inspection/Cleaning Firebox RefractoryClean Maintenance Task ListWhen cleaning glass door Chimney FireFireplace Dimensions Reference MaterialsFireplace Components Catalog # DescriptionChimney Components Catalog #330 mm 51 mm 14-3/4 375 mm This page intentionally left blank TR442 TR442 / 444 TV Minimum Base Dimensions 28 X 28 with 32 X 32 with 23 XMinimum Base Dimensions 26.5 X 28 with 34 X 34 with 20 xService Parts EXCLAIM-36-C Series Service PartsDescription of Part EXCLAIM-36T-C EXCLAIM-36H-C Qty.req This page intentionally left blank Warranty For Heat & GLO Fireplaces Limited WarrantyContact Information Do Discardnot