Heat & Glo LifeStyle EXCLAIM-36H-C, EXCLAIM-36T-C owner manual 330 mm 51 mm

Page 40

Inside Diameter 10 in. (254mm)

21 in.

(533 mm) Outside Diameter

13 in. (330 mm)

SL430 - Offset/Return

17in.

(432 mm)

A

B17 in. (432 mm)

Ceiling ﬁrestop

Catalog #	A		B
FS538	0-deg.	17 in.		432 mm
FS540	30-deg.	26 in.		660 mm

15-1/4 in.

(387 mm)

29 in.

25-1/4 in.

(641 mm)

24 in.

(610 mm)

AS10 - Straight Attic Insulation Shield

13 in.					2 in.
13 in.
(330 mm)
				(51 mm)

JB577 - Chimney Joint Band

13 in. (330 mm)

CB576 - Chimney Joint Band

(737 mm)

RF570 - Roof Flashing

15-1/4 in.

(387 mm)

28 in.

(711 mm)

39-7/8 in.

(1013 mm)

RF571 - Roof Flashing

40	Heat & Glo • EXCLAIM-36C Woodburning Fireplace • 4013-093 Rev G • 08/06

Image 40

Contents EXCLAIM-36H-C EXCLAIM-36T-C Fire RiskGrate Listing Label Information/LocationNumber Table of Contents Appliance Certiﬁcation Listing and Code ApprovalsNot intended for use as a primary heat source Design and Installation Considerations Getting StartedNegative Pressure Asphyxiation RiskMarginal Location Typical Fireplace System Typical Fireplace SystemInspect Fireplace and Components Tools and Supplies NeededFire Risk Explosion Risk Framing and Clearances Selecting Fireplace LocationClearances Failure to comply may cause ﬁreSidewalls/Surrounds Frame the FireplaceConstruct the Chase Chimney RequirementsInstallation of Fireplace Install the Outside Air KitFire Risk Sharp Edges Asphyxiation Risk Risk of Smoke SpillageFt min. from top of uppermost chimney section to air inlet Secure the Fireplace Position the FireplacePlace the Protective Metal Hearth Strips Level the FireplaceChimney Assembly Height of Chimney Components Using Offsets/Returns ¨ TableInstall the Ceiling Firestops Assemble the Chimney SectionsDouble-check the Chimney Assembly Install the Attic Insulation ShieldSecure the Chimney Complete the Enclosure Chimney TerminationInstall the Chimney Air Kit required in Canada Install the Termination CapChase Top Installing an ST475 Square Termination Cap Gas Log/Lighter Provisions AccessoriesGas Code, Ansi Z223.1 Finishing Hearth ExtensionRaised Hearth Extension Finishing Material MantelGlass Doors Combustible MaterialOperating Instructions General InformationOutside Air Clear Space Near the FireplaceFlue Damper FirescreenGrate Wood FuelFirewood MoistureStarting a Fire Troubleshooting Understanding Vent ProblemsDiagnostics and Problem Solving Diagnostic QuestionsSolutions Can’t get a good ﬁre going. What am I doing wrong?ﬁreplace burns the wood too fast. What can I do? Maintenance and Servicing the Fireplace Chimney Inspection/CleaningDisposal of Ashes Firebox RefractoryMaintenance Task List When cleaning glass doorClean Chimney FireFireplace Dimensions Reference MaterialsFireplace Components Catalog # DescriptionChimney Components Catalog #330 mm 51 mm 14-3/4 375 mm This page intentionally left blank Minimum Base Dimensions 28 X 28 with 32 X 32 with 23 X Minimum Base Dimensions 26.5 X 28 with 34 X 34 withTR442 TR442 / 444 TV 20 xService Parts EXCLAIM-36-C Series Service PartsDescription of Part EXCLAIM-36T-C EXCLAIM-36H-C Qty.req This page intentionally left blank Warranty For Heat & GLO Fireplaces Limited WarrantyContact Information Do Discardnot