Desa LHN) (V)L36(EN, LZPR) Optional HAND-HELD Remote Operation, Pilot Burner Ignitor Electrode

Page 25

OPERATING FIREPLACE

Continued

9.Slightly push in and turn control knob coun-

terclockwise to the ON position.

10.Wait one minute and switch selector switch to the ON position to light burners. Note: AUTO is only functional when using GWMT1 or GWMS2 optional accessories.

CAUTION: Do not try to ad- just heating levels by using the equipment shutoff valve.

WARNING: Make sure the selector switch is in the OFF position when you are away from home for long periods of time. Heater will come on automati- cally with selector switch in the ON position.

Pilot Burner

Ignitor

Electrode

 

Figure 38 - Propane/LP Pilot (Pilots may

vary by model)

Pilot Burner

Ignitor

 

 

Electrode

Figure 39 - Natural Pilot (Pilots may vary

by model)

TO TURN OFF GAS

TO APPLIANCE

Shutting Off Heater

1.Turn control knob clockwise to the OFF position.

2a. Set selector switch in the OFF position.

2b. If Using Optional Hand-Held Remote: Set selector switch in the OFF position to prevent draining battery.

Shutting Off Burners Only (pilot stays lit) You may shut off the burners and keep the pilot lit by doing one of the following:

1.Turn control knob clockwise to the PILOT position.

2.Use remote control manual OFF button.

3.Set selector switch in the OFF position.

MANUAL LIGHTING

PROCEDURE

1.Follow steps 1 through 6 under Lighting Instructions, page 24.

2.Depress control knob and light pilot with match.

3.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Now follow steps 9 and 10 under Lighting Instructions, column 1.

OPTIONAL HAND-HELD

REMOTE OPERATION

Note: All remote control accessories must be purchased separately (see Accessories, page

35). Follow instructions included with the remote control.

NOTICE: You must light the pilot

before using the hand-held re-

mote control unit. See Lighting

Instructions on page 24.

 

After lighting, let pilot flame burn for about

one minute. Turn control knob to ON posi-

tion. Adjust flame adjustment knob anywhere

between HI and LO. Slide the selector switch

to the REMOTE position (see Figure 40).

Note: The burner may light if hand-held

remote was on when selector switch was last

turned off. You can now turn the burner on and

off with the hand-held remote control unit.

IMPORTANT: Do not leave the selector switch

in the REMOTE or ON position when the pilot

is not lit. This will drain the battery.

 

Control Knob in

 

Flame Adjustment

On Position

 

Knob

 

 

 

OL

 

N

 

 

 

O

 

O

 

T

F

ON

O

F

HI

LIP

 

OFF

 

 

 

 

 

 

REMOTE

Selector Toggle Switch

 

(Optional Remote Control)

 

Figure 40 - Setting the Selector switch,

Control Knob and Flame Adjustment

Knob for Remote Operation

115254-01A

www.desatech.com

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents VL36EN, LEN VL32HN, LHNVL32HP, LHP VL36EP, LEPTable of Contents Safety Information Blower Accessory Product FeaturesLocal Codes OperationLocating Firebox Product SpecificationsPlanning Models42 Models Providing Adequate Ventilation AIR for Combustion VentilationDetermining FRESH-AIR Flow for Heater Location Ventilation Air From Inside Building Ventilation AIRInstallation Clearances InstallationVentilation Air From Outdoors Minimum Wall and Ceiling Clearances see ,Example BUILT-IN Firebox InstallationMinimum 16 inches from Side Wall Nails or Wood Screws Nailing Flanges Rough Opening for Installing WallInstalling Cabinet Mantel Installing Firebox Using Optional Accessory MantelsLower Louver Panel Installing Optional Blower AccessoriesDuplex Electrical Outlet Place control knob, provided, onto control shaft see Figure Wiring Diagram Decal 12 Front of BlowerInstalling Fireplace Hood and Screen HARD-WIRING FireboxDuplex Box Handy Box Strain Relief Top View of Rod LayoutInstallation Items Needed Connecting to GAS SupplyVent Pointing Down Propane/LP Checking GAS ConnectionsNatural Test Pressures Equal To or Less Than 1/2 Psig 3.5 kPa Test Pressures In Excess Of 1/2 Psig 3.5 kPaSupply Tank Correct all leaks at onceVintage Oak Two-Piece Log Set Installing LogsLog #2 Log #1 Front Post Chassis PostMetal Ember Bed Base AssemblyPost Metal PostPlace top left log on middle log as shown in Figure Operating FireplaceTop Left Log Top Right Log Middle Left Front Log Right Front LogPress in control knob and turn counter Lighting InstructionsControl Knob Ignitor ButtonREMOTE-READY Models For Your Safety Read Before Lighting Manual Lighting ProcedureVariable Control Operation To Turn OFF GAS To ApplianceBe hot if heater has been running Control Knob Flame Adjustment On Position Follow instructions included with the remote controlOptional Remote Control Optional HAND-HELD Remote OperationThermostat Series Model Ghrctb ON/OFF Series Model GhrcbPilot Flame Pattern Inspecting BurnersFront Burner Flame Pattern Cleaning Logs Cleaning MaintenanceBurner Injector Holder and Pilot AIR Inlet Hole Observed Problem Possible Cause Remedy TroubleshootingLow gas pressure Assembly Clean ODS/pilot seeLeased Long enoughObserve minimum installa When burners are lit Position when burners areBurner backfiring during com Bustion DamagedGas leak. See Warning Wiring Diagram SpecificationsMaximum Minimum Shipping Weight 104 lbs 184 lbs REMOTE-READY Models onlyTechnical Service Service HintsReplacement Parts Parts Under WarrantyAccessories Illustrated Parts Breakdown Parts Available not Shown Parts List46 39 Parts List 23/24 Not Shown 110314-05 Crossover Log Illustrated Parts Breakdown and Parts ListKEY LOG Part Numbers VL36 Models VL42 Models Description QTY Keep this Warranty Warranty InformationLimited Warranty VENT-FREE Fireplace
Top Page Image Contents