Desa FMH26NR, EFS26NR, FMH26PR, EFS10TN For Built-In Installation, Valve cover shield. see Figure

Page 13

INSTALLATION

Installing Blower Accessory GA3450T in Remote-Ready Models (Cont.)

13

INSTALLATION

Continued

3.

Note the wire locations on back of AUTO/OFF/ON switch.

 

The terminals on back of switch are numbered 1, 2, and 3.

 

Carefully remove red wire from terminal 3 and blue wire from

 

terminal 1. Black wire can remain on middle terminal 2 (see

 

Figure 16).

4.

Carefully disconnect green and white wires at their insulated

 

connectors (see Figure 17).

5.

In top of the fireplace cabinet, locate the four mounting holes

 

on the outer casing. Align these four holes with those on the

 

blower bracket assembly. Attach blower bracket assembly to

 

the outer casing with 4 #10 screws provided (see Figure 16).

6.

Route the wire harness through the hole in left side of baffle.

 

Pull wire harness through lower opening on the side of the

9.Install the switch plate on the valve cover shield with 2 #10 screws provided (see Figure 18). Route power cord out of the cabinet by inserting it through the bushing on the outer casing (see Figure 16). Plug fan kit into 120-Volt grounded power sup- ply and test operation. Note: When switch is in the AUTO posi- tion, the fan will start after the fireplace has run for a few mo- ments. The fan will continue to run for several moments after the fireplace has been turned off. When switch is in the ON position, the fan will run until turned to OFF. Reinstall upper louver assembly (see Figure 15, page 12) and branch support. Close lower louver door.

Fan Switch

(Auto/Off/On)

1Auto

 

valve cover shield. (see Figure 16).

7.

Insert the 4 wire harnesses into one of the round holes in the rear

 

of the valve cover shield and through the rectangular hole in the

 

front of shield (see Figure 16).

8.

Reconnect red wire to switch position 3. Reconnect blue wire

 

to switch position 1. Reconnect green and white wires.

 

 

Off

2

 

 

 

3

 

 

 

On

110/115

Red

 

V.A.C.

 

 

 

Black

 

 

 

 

 

 

White

 

 

 

Green

 

Blue Thermostat

Switch

(N.O.)

Blue

Blower

Motor

Red

White

Green

Blower Bracket

Wire

Wiring Routing

Harness

Hole in Baffle

Assembly

 

 

 

Screw

 

Baffle

Blower

 

 

 

Mounting

Holes

Switch

Power Cord Snap

 

 

Bushing

3

 

2

 

1

 

Switch

Plate Blue

Black Red

Wire

Harness Valve

Cover

Shield

Lower Louver Door

Figure 16 - Installing Blower Bracket Assembly

Figure 17 - Wiring Diagram For Blower Accessory Standard Installation

Valve Cover

Shield

Switch

Plate

Screw

Figure 18 - Installing Switch Plate to Valve Cover Shield

For Built-In Installation

WARNING: A licensed electrician must connect the wiring harness to electrical supply following all local codes. Electrician must provide a clamp on the box cover to secure the wiring. Wiring should be routed through the bushing in the hole on the outer casing of fireplace.

1.Install a snap bushing found in hardware kit into one of the holes on rear of valve cover shield. The other hole is for a strain relief clamp (not supplied) to secure incoming electrical supply.

2.Follow steps 2 through 6 in Installing Blower Accessory, pages 12 and 13.

For morevisit www..com

107032-01E

Page 12 Page 14
Image 13
Page 12 Page 14
Contents What to do if YOU Smell GAS OWNER’S Operation and Installation ManualSafety Information Table of ContentsVent-Free Compact Classic Hearth Fireplace Product IdentificationProduct Features Optional Remote Control AccessoriesLocal Codes UnpackingAssembling Fireplace AssemblyProviding Adequate Ventilation AIR for Combustion and VentilationDetermining FRESH-AIR Flow for Fireplace Location Ventilation Air From Inside Building Ventilation AIRVentilation Air From Outdoors InstallationCheck GAS Type Installation ItemsFireplace Clearances Minimum Clearance to Combustible MaterialsRough Opening for Installing in Wall BUILT-IN Fireplace InstallationMantel Clearances for Built-In Installation Optional Mantel InstallationInstalling Blower Accessory Removing Upper Louver Assembly and Branch SupportAssembling Brass Trim Brass trim shipped with mantel Valve cover shield. see Figure For Built-In InstallationExtension Cord Removing Upper Louver AssemblyRemoving Valve Cover Shield Installing Blower AssemblyValve Cover Shield Switch PlateScrew Attaching Wood Base to Solid Floor Connecting to GAS SupplyInstallation Items Needed Connecting Equipment Shutoff Valve to Heater ControlChecking GAS Connections Pressure Testing gas Supply Piping systemPressure Testing Fireplace Gas Connections Optional Wireless HAND-HELD Remote Control AccessoriesInstalling Receiver Optional Wall Mounted Thermostat GWMT1 Installing 9-Volt Battery in Hand-Held Remote Control UnitBack View of Thermostat Base Installing LOG SET and ScreenLighting Instructions Operating FireplaceREMOTE-READY Models For Your Safety Read Before Lighting Manual Lighting ProcedureTo Turn OFF GAS to Appliance Thermostat Control OperationPropane/LPGasPilot Natural Gas Pilot GWMT1 Wall Mounted Thermostat Optional Optional Remote OperationThermostat Control Operation Ghrcta Series OperationInspecting Burners GWMS2 Wall Mounted Switch OptionalBurner Flame Pattern Pilot Flame PatternCleaning Burner Injector Holder and Pilot AIR Inlet Hole Cleaning MaintenanceLOG SET CabinetObserved Problem Possible Cause Remedy TroubleshootingRemedy Observed Problem Possible CauseGas leak. See Warning statement Service Hints SpecificationsTechnical Service When Gas Pressure Is Too LowParts Under Warranty Replacement Parts Wiring DiagramParts not Under Warranty Remote-Ready Models OnlyTHERMOSTAT-CONTROLLED Models VMH10TPB, VMH10TNB Illustrated Parts BreakdownTHERMOSTAT-CONTROLLED Models Parts ListEFS26PR, EFS26NR REMOTE-READY ModelsParts List Accessories WALL-MOUNT Thermostat Switch GWMT1 Cleaning KIT GCKWALL-MOUNT ON/OFF Switch GWMS2 Receiver and HAND-HELD Remote Control KIT GhrcFor . .com Owners Registration Form Postage Required 107032-01E Limited Warranty VENT-FREE Compact Classic Hearth Fireplace Warranty Information
Top Page Image Contents