Nortec Industries GS Series manual Figure #7 Vertical Venting Application Using B or BH Venting

Page 12

Figure #7

Vertical Venting Application Using B or BH Venting

UL Listed Cap

Required

Flashing

B or BH type vent using double wall vent with double wall connectors is required. Reference local and/or national codes before installation of the vent.

Horizontal run

 

4" minimum air

1/4"rise per ft

 

space required

Exhaust venting

Condensate tee

outlet

required

 

 

 

 

 

B type double wall vent with

Steam Outlet

Trap

double wall connectors required

2 FT Min

for category I appliances.

 

 

3” Min.

Limitations on horizontal

 

 

distance when venting with B

 

 

vent

 

Condensate tee and

BH type double wall vent with

 

double wall connectors required

 

trap must be installed.

 

and all joints are to be air and

 

Take the condensate to

 

water tight. BH vent is a category

 

a floor drain or a

 

III appliances

 

condensate pump.

 

 

Figure # 8

Side Wall Venting Application Using BH Type Only

Wall

BH type vent using double wall vent with all joints being air and water tight. Reference local and/ or national codes before installing vent

Exhaust venting outlet

Hangers Straps

Nortec vent terminal

Condensate

Tee

Trap

2 ft Min.

Steam Outlet

3” Min.

Condensate tee and trap must be installed. Take the condensate to a floor drain or a condensate pump.

BH type double wall vent with double wall connectors is required for category III appliances

Note: These are guidelines only, follow the local and/or national codes in your respective area.

- 8 -

Image 12
Contents Installation User & Maintenance Guide For Your Safety Table Of Contents Principle of Operation General Specifications DeliveryReceiving & Unpacking Equipment Model DesignationModel Specification Figure #1 Typical Installation Indoor Locating and Mounting Side ClearanceGAS Piping GASCombustion AIR Requirements Direct Vent GuidelinesExhaust Venting General RequirementsFigure #7 Vertical Venting Application Using B or BH Venting Figure # Co-venting Application Using B Vent Only Installation as a Category I Appliance Recommended B-Venting ManufacturersInstallation as a Category III Appliance Additional Requirements When Venting Through a SidewallBH Vent Manufacturers Primary Wiring LOW Voltage Control WiringElectrical 600V/3ph 5 6 7 8 9 10 11 12 13 14 15 16 17 Control Installation PlumbingFill Water Supply Line Drain LineGS Outdoor Installation AUX Drain PortSteam Lines and Condensate Line MountingFigure # Gstc Outdoor Typical Installation Rooftop TOP GAS Piping Figure #17 Gas PipingElectrical Installation Exhaust Venting Outdoor UnitsFigure #21 Fill Water Connection Auxiliary DrainCombustion Water ManagementSteam Lines Start UP Procedure START-UP ChecklistTesting the Ignition Safety SHUT-OFF Filling the SystemStarting the Humidifier Taking OUT of OperationGS Inspection Check List Supply Water Line Factory for more informationScale Management Water QualitySafety Instructions Fault ConditionsDraining the Tank Gstc ModelsMandatory Maintenance Schedule Cleaning the Steel Tank Figure #26 Cleaning Tank AccessService Checks Combustion Blower Servicing the UnitBurner Consult Factory Prior to the Replacement of ANY Component Hot Surface Igniter and Flame Sensor ReplacementBurner Removal and Installation Removal and Installation of the Combustion Blower Gas Valve ReplacementAir Switch Replacement Float Chamber ReplacementIgnition Module Replacement Transformer ReplacementFill Valve Replacement Drain Pump Replacement Fill Box ReplacementFigure #38 Heat Exchange Assembly Removal of Heat ExchangerPage Maintenance GSP DAY DrainKeep Warm Analog ChannelMaintenance Shutdown Input ChannelTime Proportioning Blowdown GSPNortec TC Controller Main Menu System Status User Settings Status Lockout System Status 1System Status Service Interval System Status 2Service Level 1 Main Menu System Status Service Level User SettingsService Level 2 User Settings 1 User Settings 2 Main Menu System Status Service Level User SettingsUser Settings 3 TypeService Level password protected User Settings password protectedDiagnostics safety loop protected Product nameScreen Service interval Safety sensorsRemaining Start DateService Level Service intervalService history Fault history Tank DrainTank Pre-Clean Short Cycle DelayBurners User Settings Date / Time UnitsTime of day DateLanguage Controls Water ManagementFtbd Hours Ftbd Hour Blowdown RateFloat Check Fill Corrctn correction Drain Corrctn correctionDrain Cool Control InputTransducer Input Capacity LimitCalibrate Fault List Fault GIF-X See Fault List Page GS Series Internal Components Spare Parts Igniter / flame sensor gasket Page GS Series Indoor Cabinetry Spare Parts GS Series Outdoor Cabinetry Exploded View GS Outdoor Spare Parts List Page InstructionsAssembly GS Quick Reference Limited Warranty Walter Meier Climate USA Inc

GS Series specifications

Nortec Industries has established itself as a leader in the field of industrial automation, particularly with the introduction of its GS Series. This series is designed to cater to the needs of a diverse range of industries, providing advanced solutions for modern manufacturing challenges. The GS Series embodies a perfect blend of technology, precision, and versatility, designed to enhance productivity and efficiency.

One of the standout features of the GS Series is its modular design. This allows for easy customization and scalability, making it a suitable choice for businesses of any size. Users can configure their systems to meet specific operational requirements, ensuring that they get the most out of their investment. The modularity of the GS Series enables companies to start small and expand their operations as needed without extensive overhauls.

Another key characteristic of the GS Series is its incorporation of cutting-edge technologies. This series leverages artificial intelligence and machine learning algorithms to optimize production processes. These technologies enable the system to learn from real-time data, making adjustments that can significantly boost efficiency and reduce waste. Furthermore, the GS Series features advanced sensors and automation tools that allow for precise monitoring and control of manufacturing processes, ensuring that quality standards are consistently met.

The GS Series is also built with robust connectivity options, allowing for seamless integration with existing enterprise systems. This interoperability is crucial in today’s fast-paced business environment, where data-driven decision-making is key to maintaining a competitive edge. The ability to connect with Internet of Things (IoT) devices enhances the flexibility of the GS Series, enabling manufacturers to gather and analyze data from multiple sources for more informed operations.

Safety features are paramount in the design of the GS Series. Nortec Industries prioritizes the well-being of its operators by incorporating numerous safety protocols and fail-safes within the system. These features not only comply with industry standards but also ensure that operations can continue without interruptions caused by safety concerns.

In summary, Nortec Industries' GS Series represents a significant advancement in industrial automation. With its modular design, integration of AI and machine learning, robust connectivity, and inherent safety features, the GS Series is poised to drive efficiency and productivity across various sectors. Companies looking to enhance their manufacturing capabilities would find the GS Series an invaluable asset in navigating the complexities of modern production environments.