Nortec Industries GS Series manual Fill Corrctn correction, Drain Corrctn correction, Drain Cool

Page 62

Fill CORRCTN (correction)

Used for adjusting the fill rate. Adjustments to be made under factory direction only.

Drain CORRCTN (correction)

Used for adjusting the drain rate. Adjustments to be made under factory direction only.

Drain Cool

The customer can select the type of drain water tempering they require (depending on local plumbing codes)

The customer can select ON, OFF, or SMART.

ON – whenever the drain valve is activated through software, the fill valve will automatically activate. This is the factory default setting, but is the most wasteful of water since it will activate even if the drain water is cool.

OFF – The drain water is never tempered. This can be used where plumbing codes permit. Some process waters are very expensive, so the customer may choose to temper the drain water through other means.

SMART – The humidifier has a tank sensor that communicates the water temperature to the controller. If the water is hot during drain cycles the fill valve will be activated. This is the most “water smart” of the settings.

DATE/TIME/UNITS

LANGUAGE CONTROLS

WATER MANAGEMENT

CONTROL TYPE

CAPACITY LIMIT

CALIBRATE

CONTROL TYPE CONTROL INPUT TRANSDUCER INPUT

0335

CONTROL TYPE CONTROL INPUT TRANSDUCER INPUT

Control Input

This section is used for configuring the controller for a controller input or a transducer input.

To select control input, highlight the selection then enter the user code (0335). Press enter. Use the UP/DOWN arrows to select control input.

The controllers dip switches then determine the type (0-10 Vdc, 0-20 mA, etc.) of control signal to process.

- 58 -

Image 62
Contents Installation User & Maintenance Guide For Your Safety Table Of Contents Principle of Operation Receiving & Unpacking Equipment General SpecificationsDelivery Model DesignationModel Specification Figure #1 Typical Installation Indoor Locating and Mounting Side ClearanceGAS Piping GASCombustion AIR Requirements Direct Vent GuidelinesExhaust Venting General RequirementsFigure #7 Vertical Venting Application Using B or BH Venting Figure # Co-venting Application Using B Vent Only Installation as a Category I Appliance Recommended B-Venting ManufacturersBH Vent Manufacturers Installation as a Category III ApplianceAdditional Requirements When Venting Through a Sidewall Electrical Primary WiringLOW Voltage Control Wiring 600V/3ph 5 6 7 8 9 10 11 12 13 14 15 16 17 Fill Water Supply Line Control InstallationPlumbing Drain LineSteam Lines and Condensate Line GS Outdoor InstallationAUX Drain Port MountingFigure # Gstc Outdoor Typical Installation Rooftop TOP GAS Piping Figure #17 Gas PipingElectrical Installation Exhaust Venting Outdoor UnitsFigure #21 Fill Water Connection Auxiliary DrainSteam Lines CombustionWater Management Testing the Ignition Safety SHUT-OFF Start UP ProcedureSTART-UP Checklist Filling the SystemStarting the Humidifier Taking OUT of OperationGS Inspection Check List Supply Water Line Factory for more informationScale Management Water QualityDraining the Tank Safety InstructionsFault Conditions Gstc ModelsMandatory Maintenance Schedule Cleaning the Steel Tank Figure #26 Cleaning Tank AccessBurner Service Checks Combustion BlowerServicing the Unit Burner Removal and Installation Consult Factory Prior to the Replacement of ANY ComponentHot Surface Igniter and Flame Sensor Replacement Removal and Installation of the Combustion Blower Gas Valve ReplacementAir Switch Replacement Float Chamber ReplacementFill Valve Replacement Ignition Module ReplacementTransformer Replacement Drain Pump Replacement Fill Box ReplacementFigure #38 Heat Exchange Assembly Removal of Heat ExchangerPage Keep Warm Maintenance GSPDAY Drain Analog ChannelTime Proportioning Maintenance ShutdownInput Channel Blowdown GSPNortec TC Controller Main Menu System Status User Settings Status Lockout System Status 1System Status Service Interval System Status 2Service Level 1 Main Menu System Status Service Level User SettingsService Level 2 User Settings 1 User Settings 2 Main Menu System Status Service Level User SettingsUser Settings 3 TypeDiagnostics safety loop protected Service Level password protectedUser Settings password protected Product nameScreen Remaining Service intervalSafety sensors Start DateService history Service LevelService interval Fault history Tank DrainBurners Tank Pre-CleanShort Cycle Delay Time of day User SettingsDate / Time Units DateFtbd Hours Language ControlsWater Management Float Check Ftbd HourBlowdown Rate Drain Cool Fill Corrctn correctionDrain Corrctn correction Control InputCalibrate Transducer InputCapacity Limit Fault List Fault GIF-X See Fault List Page GS Series Internal Components Spare Parts Igniter / flame sensor gasket Page GS Series Indoor Cabinetry Spare Parts GS Series Outdoor Cabinetry Exploded View GS Outdoor Spare Parts List Page InstructionsAssembly GS Quick Reference Limited Warranty Walter Meier Climate USA Inc

GS Series specifications

Nortec Industries has established itself as a leader in the field of industrial automation, particularly with the introduction of its GS Series. This series is designed to cater to the needs of a diverse range of industries, providing advanced solutions for modern manufacturing challenges. The GS Series embodies a perfect blend of technology, precision, and versatility, designed to enhance productivity and efficiency.

One of the standout features of the GS Series is its modular design. This allows for easy customization and scalability, making it a suitable choice for businesses of any size. Users can configure their systems to meet specific operational requirements, ensuring that they get the most out of their investment. The modularity of the GS Series enables companies to start small and expand their operations as needed without extensive overhauls.

Another key characteristic of the GS Series is its incorporation of cutting-edge technologies. This series leverages artificial intelligence and machine learning algorithms to optimize production processes. These technologies enable the system to learn from real-time data, making adjustments that can significantly boost efficiency and reduce waste. Furthermore, the GS Series features advanced sensors and automation tools that allow for precise monitoring and control of manufacturing processes, ensuring that quality standards are consistently met.

The GS Series is also built with robust connectivity options, allowing for seamless integration with existing enterprise systems. This interoperability is crucial in today’s fast-paced business environment, where data-driven decision-making is key to maintaining a competitive edge. The ability to connect with Internet of Things (IoT) devices enhances the flexibility of the GS Series, enabling manufacturers to gather and analyze data from multiple sources for more informed operations.

Safety features are paramount in the design of the GS Series. Nortec Industries prioritizes the well-being of its operators by incorporating numerous safety protocols and fail-safes within the system. These features not only comply with industry standards but also ensure that operations can continue without interruptions caused by safety concerns.

In summary, Nortec Industries' GS Series represents a significant advancement in industrial automation. With its modular design, integration of AI and machine learning, robust connectivity, and inherent safety features, the GS Series is poised to drive efficiency and productivity across various sectors. Companies looking to enhance their manufacturing capabilities would find the GS Series an invaluable asset in navigating the complexities of modern production environments.