Nortec Industries GS Series Service interval, Remaining, Start Date, Security loop, Tank sensor

Page 55

SCREEN 4:

SERVICE INTERVAL

XXX HOURS

REMAINING XXX HOURS

START DATE: MM:DD:YY

Service interval:

This field displays the user (or factory default) setting for the humidifiers service reminder in steam hours.

Remaining:

This field displays the amount of time (steam hours) remaining before the next service is to be performed.

Start Date:

This field displays the date this service interval began.

SCREEN 5:

SECURITY LOOP [0/1]

SAFETY SENSORS [0/1]

TANK SENSORS [0/1]

Security loop:

This field displays the status of the security loop (terminals 1 and 2 on LV terminal strip). If it is open the display will indicate “O”, if it is closed the display will indicate “I”.

Safety sensors:

This field displays the status of the safety sensors* input. If it is open the display will indicate “0”, if it is closed the display will indicate “1”.

*There are two safety sensors on the GSTC. One for tank over temperature and one for stack over temperature. Both sensors are wired in series.

Tank sensor

This field displays the status of the tank sensor input. If it is open the display will indicate “0”, if it is

closed the display will indicate “1”. Closed indicates that the tank temperature is above 160ºF (70ºC).

This input is used for the “keep warm” feature and for activating the fill valve during blowdown cycles.

SCREEN 6:

3 DAY DRAIN

1

KEEP WARM

0

BLOWDOWN RATE

XX%

FT BLOWDOWN

1

3 day drain

This field indicates if the feature has been selected (0 = no, 1 = yes).

Keep warm

This field indicates if the feature has been selected (0 = no, 1 = yes).

Blowdown rate:

This field displays the selected blowdown rate.

Full tank blowdown

This field indicates if the feature has been selected (0 = no, 1 = yes).

- 51 -

Page 54 Page 56
Image 55
Page 54 Page 56
Contents Installation User & Maintenance Guide For Your Safety Table Of Contents Principle of Operation Model Designation General SpecificationsDelivery Receiving & Unpacking EquipmentModel Specification Figure #1 Typical Installation Indoor Side Clearance Locating and MountingGAS GAS PipingDirect Vent Guidelines Combustion AIR RequirementsGeneral Requirements Exhaust VentingFigure #7 Vertical Venting Application Using B or BH Venting Figure # Co-venting Application Using B Vent Only Recommended B-Venting Manufacturers Installation as a Category I ApplianceAdditional Requirements When Venting Through a Sidewall Installation as a Category III ApplianceBH Vent Manufacturers LOW Voltage Control Wiring Primary WiringElectrical 600V/3ph 5 6 7 8 9 10 11 12 13 14 15 16 17 Drain Line Control InstallationPlumbing Fill Water Supply LineMounting GS Outdoor InstallationAUX Drain Port Steam Lines and Condensate LineFigure # Gstc Outdoor Typical Installation Rooftop TOP Figure #17 Gas Piping GAS PipingExhaust Venting Outdoor Units Electrical InstallationAuxiliary Drain Figure #21 Fill Water ConnectionWater Management CombustionSteam Lines Filling the System Start UP ProcedureSTART-UP Checklist Testing the Ignition Safety SHUT-OFFTaking OUT of Operation Starting the HumidifierGS Inspection Check List Factory for more information Supply Water LineWater Quality Scale ManagementGstc Models Safety InstructionsFault Conditions Draining the TankMandatory Maintenance Schedule Figure #26 Cleaning Tank Access Cleaning the Steel TankServicing the Unit Service Checks Combustion BlowerBurner Hot Surface Igniter and Flame Sensor Replacement Consult Factory Prior to the Replacement of ANY ComponentBurner Removal and Installation Gas Valve Replacement Removal and Installation of the Combustion BlowerFloat Chamber Replacement Air Switch ReplacementTransformer Replacement Ignition Module ReplacementFill Valve Replacement Fill Box Replacement Drain Pump ReplacementRemoval of Heat Exchanger Figure #38 Heat Exchange AssemblyPage Analog Channel Maintenance GSPDAY Drain Keep WarmBlowdown GSP Maintenance ShutdownInput Channel Time ProportioningNortec TC Controller System Status 1 Main Menu System Status User Settings Status LockoutSystem Status 2 System Status Service IntervalMain Menu System Status Service Level User Settings Service Level 1Service Level 2 User Settings 1 Main Menu System Status Service Level User Settings User Settings 2Type User Settings 3Product name Service Level password protectedUser Settings password protected Diagnostics safety loop protectedScreen Start Date Service intervalSafety sensors RemainingService interval Service LevelService history Tank Drain Fault historyShort Cycle Delay Tank Pre-CleanBurners Date User SettingsDate / Time Units Time of dayWater Management Language ControlsFtbd Hours Blowdown Rate Ftbd HourFloat Check Control Input Fill Corrctn correctionDrain Corrctn correction Drain CoolCapacity Limit Transducer InputCalibrate Fault List Fault GIF-X See Fault List Page GS Series Internal Components Spare Parts Igniter / flame sensor gasket Page GS Series Indoor Cabinetry Spare Parts GS Series Outdoor Cabinetry Exploded View GS Outdoor Spare Parts List Page InstructionsAssembly GS Quick Reference Limited Warranty Walter Meier Climate USA Inc

GS Series specifications

Nortec Industries has established itself as a leader in the field of industrial automation, particularly with the introduction of its GS Series. This series is designed to cater to the needs of a diverse range of industries, providing advanced solutions for modern manufacturing challenges. The GS Series embodies a perfect blend of technology, precision, and versatility, designed to enhance productivity and efficiency.

One of the standout features of the GS Series is its modular design. This allows for easy customization and scalability, making it a suitable choice for businesses of any size. Users can configure their systems to meet specific operational requirements, ensuring that they get the most out of their investment. The modularity of the GS Series enables companies to start small and expand their operations as needed without extensive overhauls.

Another key characteristic of the GS Series is its incorporation of cutting-edge technologies. This series leverages artificial intelligence and machine learning algorithms to optimize production processes. These technologies enable the system to learn from real-time data, making adjustments that can significantly boost efficiency and reduce waste. Furthermore, the GS Series features advanced sensors and automation tools that allow for precise monitoring and control of manufacturing processes, ensuring that quality standards are consistently met.

The GS Series is also built with robust connectivity options, allowing for seamless integration with existing enterprise systems. This interoperability is crucial in today’s fast-paced business environment, where data-driven decision-making is key to maintaining a competitive edge. The ability to connect with Internet of Things (IoT) devices enhances the flexibility of the GS Series, enabling manufacturers to gather and analyze data from multiple sources for more informed operations.

Safety features are paramount in the design of the GS Series. Nortec Industries prioritizes the well-being of its operators by incorporating numerous safety protocols and fail-safes within the system. These features not only comply with industry standards but also ensure that operations can continue without interruptions caused by safety concerns.

In summary, Nortec Industries' GS Series represents a significant advancement in industrial automation. With its modular design, integration of AI and machine learning, robust connectivity, and inherent safety features, the GS Series is poised to drive efficiency and productivity across various sectors. Companies looking to enhance their manufacturing capabilities would find the GS Series an invaluable asset in navigating the complexities of modern production environments.
Top Page Image Contents