Nilfisk-ALTO 692003 manual Post Operation Checklist, To Drain Recovery Tank

Page 39

OPERATING INSTRUCTIONS

POST OPERATION CHECKLIST

Check Battery Condition and recharge, if necessary.

1.Check all flaps for wear, damage and adjustment.

2.Drain and clean recovery tank.

3.Clean recovery tank screen and float.

4.Check scrub brushes for wear or damage.

5.Check rear and side squeegee for wear, damage and adjustment.

6.Clean the debris in hopper

7.Check main and side broom for wear or damage.

DRAIN HOSE PLUG

DRAIN HOSE

DRAIN HOSE PLUG

DRAIN HOSE

Fig. 42

Fig. 43

 

TO DRAIN RECOVERY TANK

PLACE HOSE OVER DRAIN

Fig. 44

WHEN REPLACING DRAIN HOSE CLIP ON DRAIN HOSE PLUG

FACES OUT

Fig. 45

TO DRAIN RECOVERY TANK

The drain hose for the recovery tank is located on the back of the machine. To drain the tank, remove and lower the hose and place in a suitable floor drain as shown in figure 44. Open the drain hose plug as shown in figure 42 and 43.

IMPORTANT

Improper discharge of wastewater will damage the environment and is illegal. The U.S. Environmental Protection Agency has established certain regulations regarding discharge of wastewater. The local city and state regulations regarding wastewater discharge may be in effect in your area. Understand and follow the regulations in your area. Be aware of the environmental hazards associated with the substances you dispose of.

AMERICAN-LINCOLN

1-39

SMART

 

Image 39
Contents American-Lincoln AMERICAN-LINCOLN Index Disclaimer DisclaimerDecimal Metric Conversion Table Hardware Abreviations ABBREVIATIONS-SCREWSABREVIATIONS-SETSCREWS SAE Grade Standard Hardware & Torque ValuesHydraulic Torque Requirements Hydraulic Torque RequirementsSymbols Parts may be ordered from Alto distributors Ordering PartsSafety Precautions Personal Safety Machine SafetyHazard Seriousness Level Safety Precautions Specifications Squeegee WarrantyInstruments and Controls Scrubbing SystemLWA Unpacking and Assembling Machine Machine PreparationUnpacking Battery Battery Installation Controls Forward / Reverse Switch KEY SwitchHour Meter Battery Condition MeterHopper Open Light Warning HEADLIGHT/TAILIGHT Switch OptionalDust Control Switch Filter Shaker Switch Only models with dust controlSqueegee Switch Scrub Brush SwitchHigh Recovery Light LOW Solution LightSide Broom and Main Broom Switch Hopper Lift SwitchSpray and VAC Wand Switch Optional Main Broom Adjustment Side Broom AdjustmentHorn Button Solution Flow KnobParking Brake Foot ThrottleSafety Features Seat Position AdjustmentOperating Instructions PRE-START ChecklistTo Transport Machine To Start MachineScrubbing the Average Floor with Light to Medium Soilage To Begin the Cleaning OperationFloor Contact NON-RECYCLING or Standard Scrubbing ModeScrub Brush Squeegee Floor Contact ESP Operating ModeScrubbing Path To Stop the Cleaning OperationTo Drain Recovery Tank Post Operation ChecklistRecovery Tank Hose Disk Scrub Brushes Operating Instructions Hydraulic Reservoir Level Sight Gauge Dust Control KnobHour Maintenance Checklist MaintenanceService Chart Hour Weekly Maintenance Checklist11, 12 Maintenance Battery Charging Instructions Battery Removal Battery Removal with the Battery Rollout Option Replacing Pads on a PAD Driver Replacing Scrub BrushesReplacing Rear Squeegee Draining the Solution Tank Draining the Recovery TankAdjusting the Main Broom Height Replacing the Main Broom Main Broom Access DoorBroom Lift ARM Broom Idler Side Broom Adjustment Knob Checking the Dust Control Filter Cleaning the Dust Control FilterReplacing the Dust Control Filter When Damage is Evident Dust Control FilterChecking the Dust Flaps Adjusting the Dust FlapsCleaning the Hydraulic System Dust FlapsProblem Probable Cause TroubleshootingRemedy