Nilfisk-ALTO 4800, 5400 16 / English, Detergent System Preparation and USE AXP/EDS Models only

Page 16

A-16 / ENGLISH

DETERGENT SYSTEM PREPARATION AND USE (AXP/EDS MODELS ONLY)

Fill the detergent cartridge with a maximum of 2.2 gallons (8.32 Liters) of detergent. SERVICE NOTE: Remove the detergent cartridge from the detergent box prior to lling to avoid spilling detergent on the machine.

It is recommended that a separate cartridge be used for each detergent you plan to use. The detergent cartridges have a white decal on them so you can write the detergent name on each cartridge to avoid mixing them up. The detergent cartridge has a Magnetic Slider (A) on one end that should be set to the proper dilution ratio according to the dilution instructions on the manufacturer’s bottle. Slide the Magnet Slider (A) to the appropriate location on Detergent Dilution Ratio Decal (B). When installing a new cartridge, remove the Cap (C) and place the cartridge in the detergent box. Install the Dry Break Cap (D) as shown.

The system should be purged of previous detergent when switching to a different detergent. SERVICE NOTE: Move machine over oor drain before purging because a small amount of detergent will be dispensed in the process.

To Purge When Changing Chemicals:

1Disconnect and remove the detergent cartridge.

2Turn the Key Switch (MM) ON and press the Detergent ON/OFF Switch (RR) for at least 2 seconds. NOTE: Once activated the purge process takes about 10 seconds. See illustration on next page for Detergent System indicators. Normally one purge cycle is adequate to purge the system.

To Purge Weekly:

1Disconnect and remove the detergent cartridge. Install and connect a Cartridge lled with clean water

2Turn the Key Switch (MM) ON and press the Detergent ON/OFF Switch (RR) for at least 2 seconds. NOTE: Once activated the purge process takes about 10 seconds. See illustration on next page for Detergent System indicators. Normally one purge cycle is adequate to purge the system.

The Detergent Box (E) has a Detergent Level Viewing Slot (F) for keeping track of how much detergent is remaining in the cartridge. When the detergent level is nearing the bottom of this slot it is time to rell or replace the cartridge.

General Use:

The detergent (AXP/EDS) system is enabled when the Key Switch (MM) is turned on and reverts to the last state (Chem On or Chem Off) it was in prior to the last power down. The current Solution Flow Rate (VV) and the last used Detergent Ratio (WW) (if in “Chem On” state) are displayed. The Status LED (YY) indicates the status of the system as follows:

GREEN: Solution not low and chemical pump ON (pumping solution and chemical)

BLINKING GREEN: Purge has been activated

LED OFF: Solution ow position = 0 or solution solenoid is OFF

ORANGE: Solution ON and Chemical OFF (pumping solution only)

BLINKING RED: Solution low and chemical pump ON (pumping solution only)

No detergent is dispensed until the scrub system is activated and the Drive Pedal (OO) pushed forward. The detergent ratio can be varied by subsequently pressing the Detergent Increment and Decrement Switches (SS & TT). The detergent ow rate increases or decreases with the solution ow rate but the detergent ratio remains the same unless changed. During scrubbing, the detergent system can be turned off at any time by pressing the Detergent ON/OFF Switch (RR) to allow scrubbing with water only. On AXP/EDS models the solution ow rate (40%-100%) is electronically controlled and is displayed (VV) on the AXP/EDS display panel as shown below.

SERVICE NOTE: Follow the “To Purge Weekly” instructions above if the machine is going to be stored for an extended period of time or if you plan to discontinue use of the detergent (AXP/EDS) system. The Display Panel (UU) will display an Error Code “E1” (XX) in the lower left corner if the magnetic slider circuit board (ZZ) becomes disconnected or malfunctions.

A-16- FORM NO. 56041580 - Captor4300, 4800, 5400 / CR 1100, 1200, 1400

revised 3/08

Image 16
Contents Captor 4300, 4800 CR 1100, 1200 Page Table of Contents English / A-3Parts and Service EnglishIntroduction NameplateSymbols English / A-5Consignes DE Prudence ET DE Securite Symboles English / A-7 Know Your Machine English / A-9 10 / English OPERATOR’S CompartmentEnglish / A-11 PRE-OPERATIONAL Checklist 12 / EnglishMain Broom Scrub BrushesEnglish / A-13 14 / English English / A-15 16 / English Detergent System Preparation and USE AXP/EDS Models onlyEnglish / A-17 18 / English Sweeping English / A-19Emptying the Hopper 20 / English ScrubbingEnglish / A-21 Maintenance Schedule 22 / EnglishRight Side View of Broom Housing Main Broom MaintenanceEnglish / A-23 24 / English Side Broom MaintenanceTOP View of Hopper Squeegee Maintenance English / A-2526 / English Hopper Dust Control FilterEngine OIL Gasoline Petrol & LPG Engine OIL DieselEnglish / A-27 Engine CoolantEngine AIR Filter Circuit Breaker Location28 / English TroubleshootingTripping the Circuit Breakers English / A-29 30 / English Captor 4300 LPGEnglish / A-31 Captor 4300 LPG-AXPEspañol ÍndiceEspañol / B-3 IntroducciónComponentes Y Servicio Placa DE IdentificaciónPrecauciones Y Advertencias Símbolos Español / B-5 Conozca SU Máquina Español / B-7 Conozca SU Máquina ContinuaciónCompartimiento DEL Operario Español / B-9 Compartimiento DEL Operario Continuación10 / Español Comprobaciones Previas a LA UtilizaciónCepillo Principal Cepillos DE FregadoEspañol / B-11 12 / Español Español / B-13 14 / Español Purgar al cambiar productos químicosEspañol / B-15 16 / Español Barrido Español / B-17Vaciado DE LA Tolva 18 / Español FregadoEspañol / B-19 20 / Español Programa DE MantenimientoMantenimiento DEL Cepillo Principal Español / B-21Vista Lateral Derecha DEL Alojamiento DEL Cepillo Mantenimiento DEL Cepillo Lateral 22 / EspañolVista Desde Arriba DE LA Tolva Español / B-23 Mantenimiento DE LA Boquilla24 / Español Filtro DE Control DE Polvo DE LA TolvaAceite DEL Motor Gasolina Y Propano Líquido Aceite DEL Motor DieselEspañol / B-25 Líquido DE Refrigeración DEL MotorFiltro DEL Aire DEL Motor Ubicación DE LOS DisyuntoresLocalización DE Averías 26 / EspañolDesconexión DE LOS Disyuntores Español / B-27 28 / Español Captor 4300 LPGEspañol / B-29 Captor 4300 LPG-AXPPage Page Page Nilfisk-Advance Inc., F00018, 1/99 2008

4800, 4300, 5400 specifications

Nilfisk-ALTO, a recognized leader in cleaning equipment, has developed a range of high-performance industrial vacuums to meet the demanding needs of various industries. Among these models are the Nilfisk-ALTO 5400, 4800, and 4300, each offering distinctive advantages while sharing a robust foundation built on efficiency, durability, and cutting-edge technology.

Starting with the Nilfisk-ALTO 5400, this model is engineered for heavy-duty applications and provides exceptional suction power thanks to its advanced turbine system. With a large capacity for collecting waste materials, the 5400 is particularly adept at handling fine dust and debris in environments such as construction sites and manufacturing facilities. The integrated filtration system not only ensures efficient dust containment but also extends the lifespan of the vacuum by minimizing clogging.

Moving to the Nilfisk-ALTO 4800, this model strikes a balance between performance and versatility. It features a compact design making it easy to transport, while still delivering powerful suction for a wide range of applications. The 4800 is equipped with an effective HEPA filter that captures 99.997% of particles larger than 0.3 microns, ensuring compliance with strict air quality standards. Additionally, its user-friendly controls and ergonomic features enhance operator comfort during prolonged use.

The Nilfisk-ALTO 4300 is designed with smaller spaces in mind, yet offers a surprising level of performance. This model is perfect for light to medium-duty tasks, with an efficient motor that provides solid suction power without excessive noise. It is particularly suitable for cleaning in offices, schools, and retail spaces where disruption needs to be minimized. The 4300’s compact size allows for easy maneuverability and storage, making it an ideal choice for team environments and smaller cleaning crews.

All three models integrate advanced technologies such as the innovative DustGuard filtration system and an easy-to-clean design, which significantly reduces maintenance time and enhances overall operational efficiency. Their construction with durable materials ensures longevity, making them reliable investment choices for businesses focused on maximizing productivity while maintaining a clean and safe working environment.

In conclusion, the Nilfisk-ALTO 5400, 4800, and 4300 are exemplary industrial vacuums that cater to diverse cleaning needs, confirming Nilfisk-ALTO's commitment to quality, innovation, and customer satisfaction.