Integra RDC-7.1 instruction manual Connecting a DBS Tuner, DBS TV, or BS/CS Tuner

Connecting AV Components—Continued

Connecting a DBS Tuner, DBS TV, or BS/CS Tuner

For USA and Canadian models, this type of connection is only possible if an option board that has an appropriate terminal is installed.

•When connecting a DBS tuner, DBS TV, or BS/CS tuner to the RDC-7.1, make connections for video and audio sig- nals using digital and analog terminals. Before making connections, refer to pages 30, 31 for correct connections.

•This section shows the connection example when you use the VIDEO 4 or VIDEO 5 as an input. In this case, you do not need additional configurations. When connecting to other terminals within the same terminal section on the RDC-7.1, remember to configure the audio input assignment in the Audio Assign sub-menu (See page 98) and the video input assignment in the Video Assign sub-menu (See page 99). When you use the S VIDEO terminal for con- nection, you should configure the Video Assign sub-menu.

•You can change the display name for the input source to represent the actual connected device (See page 101).

•For a model without a slot for the HDMI terminal, when you connect a BS/CS tuner or LD player to the COMPO-

NENT terminals, be sure to use the COMPONENT terminals to connect a TV or projector.

*For more information on the HDMI interface, see page 43.

*For more information on the i.LINK (AUDIO) interface, see page 40.

Example for connecting with the VIDEO 4 as input

When connecting to other audio termi-	AUDIO OUT	AUDIO OUT		When connecting to other video termi-
nals within the same terminal section,				nals within the same terminal section,
	DIGITAL	ANALOG	VIDEO
configure the audio input settings	OPTICAL	R L	OUT	configure the video input settings
accordingly using the Audio Assign				accordingly using the Video Assign
sub-menu (See page 98).				sub-menu (See page 99).

Installation and Connections

A	B	C DIGITAL IN	D DIGITAL IN
		OPTICAL	COAXIAL
		1	1
		2	2
	“Net-Tune”	3	3
	is a trademark of
	Onkyo Corporation.
		4	4
	ETHERNET	5	5
	(Net -Tune)
		6	6
		1	1

E		- CH	F	AUDIO IN	G
		MULTI	R	L	R	L
FR	FL	IN 1
			PH		4
SUB		C
					5
				GND
SR		SL	R	L
			1		6

SBR SBL

27

38

19

24

DIGITAL IN

( BALANCED )

AES/EBU

H S VIDEO VIDEO

IN IN

1

2

3

4

5

6

1

I	COMPONENT	J		K
	VIDEO
IN 1	IN 2	COMPONENT VIDEO		ANTENNA
		((HDHD/BNC/BNC))	IN
	Y		Y
	PB
			PB
	PR			FM
OUT 1	IN 3			75

PR
Y
OUT
PB
Y	AM

PR

PB

3

PR

L

HDMI		RS232
IN 1
HDMI, the HDMI logo	REMOTE	12V
	CONTROL
is a trademark		TRIGGER
or registered		OUT
trademarks of HDMI		A
Licensing LLC.
		200mA MAX.
IN 2	B 100mA MAX.
		C
		100mA MAX.

D100mA MAX.

E

100mA MAX.

MAIN

ZONE 2

2	2
	OUT

3		5
R	L	OUT R	L

2		4
	OUT	OUT
S VIDEO	VIDEO	VIDEO	S VIDEO

ZONE 3	UPP
OUT
IN	OUT
	IR
AC INLET

(ASSIGNABLE)(ASSIGNABLE)

(SINGLE)

	R	L
AUDIO OUT	AUDIO OUT
DIGITAL		VIDEO
COAXIAL		OUT

When connecting to other audio terminals within the same terminal section, con- figure the audio input settings accordingly using the Audio Assign sub-menu (See page 98).

When connecting to other video terminals within the same terminal section, con- figure the video input set- tings accordingly using the Video Assign sub-menu (See page 99).

Example for connecting with the VIDEO 5 as input

37