Integra RDC-7.1 Input Setup, Audio Assign Sub-menu when input is other than NET Audio

Input Setup—Continued

Follow procedures below to change any setting:

1	Press the [Input] button, and then roll the
	scroll wheel to select the input source that
	you want to set.
2	Press the scroll wheel, and then press the
	[Setup] button.
	The Main Menu appears onscreen.
3	Use the [	]/[	] buttons to select “Input
	Setup,” and then press the [Enter] button.
	The sub-menu is displayed.
		2.Input Setup
		==Input:XXXXXX=======
		1.Audio Assign
		2.Video Assign
		3.Listening Mode Preset
		4.Character Edit
		5.IntelliVolume
		6.Delay
		7.Picture Setting
		8.12V Trigger Assign
4	Use the [	]/[	] buttons to select an item
	you want to set, and then use the [ ]/[ ]
	buttons to set the desired value.
	Other items should be selected in the same way.
5	Press the [Return] button.
	The display returns to the sub-menu.
6	Repeat procedures 4-5 to set desired
	items sequentially.
	When all of the items are set, go to procedure 7.
7	Press the [Setup] button.
	Settings are completed and the menu screen

disappears.

Hint:

When you perform the procedures on the RDC-7.1, after selecting the input source using the input source buttons, press the [Setup] button. Next, select the menu you want to configure by pressing the []/[ ] buttons and press the [Enter] button to confirm the selection. Then, after selecting the sub-menu you want to

configure by pressing the [	]/[ ] buttons, select your
value by pressing the [ ]/[	] buttons, and press the

[Enter] button to confirm the value. If you want to go back to the previous operation, press the [Exit] button.

Example 1

In assignment of a DVD recorder to input of VIDEO 1, when the analog audio input is connected to “VIDEO 1,” the digital audio to “COAXIAL 2,” and the video to “S VIDEO 2” and “COMPONENT 2.”

1.Press the [Input] button, and then roll the scroll wheel to select “VIDEO 1.”

2.Press the scroll wheel, and then press the [Setup] button to display the Main Menu.

3. Use the []/[ ] buttons to select “Input Setup,” and then press the [Enter] button.

98

4.	Use the [	]/[	] buttons to select “Audio Assign”
	from the sub-menu, and then press the [Enter] but-
	ton.
5.	Use the [	]/[	] buttons to select “Analog Audio,”
	and then use the [			]/[	] buttons to select “1.”
6.	Use the [	]/[	] buttons to select “Digital Audio,”
	and then use the [			]/[	] buttons to select “Coax 2.”
7.	Press the [Return] button to return to the sub-menu.
8.	Use the [	]/[	] buttons to select “Video Assign,”
	and then press the [Enter] button.
9.	Use the [	]/[	] buttons to select “S-Video,” and
	then use the [		]/[	] buttons to select “2.”
10.	Use the [	]/[	] buttons to select “Component
	Video,” and then use the [ ]/[ ] buttons to select
	“RCA 2.”

11.Press the [Setup] button.

Setting is completed and the menu screen disap- pears.

Audio Assign Sub-menu (when input is other than NET AUDIO)

The following are settings for audio. When input is “NET AUDIO,” see the following page.

Analog Audio

The following are settings for analog audio output: Phono: Select the device connected to “AUDIO IN PH.”

1-9:Select the device connected to the jack of “AUDIO IN 1-9.”

No: Select this when no device is connected.

Multichannel

This item appears when the multichannel terminal board

[E]is inserted. When the multichannel terminal board contains a single set of multichannel terminals, available options are “1” and “No.”

1: Select the device connected to the jack of “MULTI- CH IN 1.”

2: Select the device connected to the jack of “MULTI- CH IN 2.”

No (Default): Select this when no device is connected.

Surr Back Channel

This item appears when the multichannel terminal board [E] is inserted.

The following are settings for “Multichannel 1” or “Multichannel 2” described above, and cannot be specified separately for each input source. For example, when the input source is CD and “Surround Back Channel” is set to “Not Used (5.1 ch)” for “Multichannel 1,” switching the input source to DVD and “Surround Back Channel” to “SBL/SBR (7.1ch)” will also change “Surround Back Channel” associated with CD to “SBL/SBR (7.1ch).”

Not Used (5.1 ch): Select this when not using the surround back channel.