Integra DTR-4.5 instruction manual Using Zone

Zone 2—Continued

Using Zone 2

Here you can turn on Zone 2, select an input source, and adjust the volume.

1	On	Standby		T V	4
			I
				Input
	V1	V 2	V 3
	1	2	3	+
		Multi CH	DVD	TV CH
	4	5	6	-
2	CD	Tape	Tuner
	7	8	9
				TV VOL
	+10	0	Clear
	--/---	Input Selector
		Macro			1–4
	1	2	3	Zone 2
		Remote Mode
	Receiver	DVD	CD	MD/CDR
	Tape
	TV	VCR	Cable	SAT
	Audio	Subtitle	Angle	Last Memory
	Surround	All ST		Stereo
	Repeat	A-B	Search	Memory

To set Zone 2 to the same source as the main room, press the [ZONE 2] button, and then use the Controller []/[ ] buttons to select “Zone 2 Sel: Source.”

3	To adjust the Zone 2 volume with
Zone 2	the remote controller, press the
	[ZONE 2] button, and then use
	the [Level–] and [Level+] buttons.
Level- Level+	To do this on the AV receiver,
	press the Zone 2 [Level] button,
	and then use the Controller [ ]/
	[ ] buttons.
	If the Zone 2 receiver/integrated amp is
	connected to the AV receiver’s ZONE 2
	OUT L/R jacks, use the volume control
	on the receiver/integrated amp.

	Direct	DSP	DSP
Test Tone	CH SEL	Level-	Level+	3
Open/Close	Video Off
		L Night	Cine Fltr
	RC-587M

Note:

To control Zone 2 with the remote controller, you must press the [ZONE 2] button first.

4

Zone 2

Standby

To turn off Zone 2 with the remote controller, press the [ZONE 2] button followed by the [Standby] button.

To do this from the AV receiver, press the [ZONE 2] button, and then use the Controller []/[ ] buttons to select OFF.

1	Point the remote controller at the
	Zone 2

AV receiver and press the [ZONE 2] button followed by the [On] button.

On

Notes:

• If the Sleep function has been set, the Zone 2 compo-

nent will turn off along with the AV receiver when the

specified sleep time expires. To use the Sleep function

with Zone 2 only, set the Sleep function and then set

the AV receiver to Standby.

• Only analog input sources are output by the ZONE 2

OUT and ZONE 2 SPEAKERS terminals. Digital

input sources are not output. If no sound is heard when

2

Zone 2

V1 V 2 V 3

Multi CH DVD

CD Tape Tuner

To select the Zone 2 input source with the remote controller, press the [ZONE 2] button followed by an input selector button.

If you select AM or FM, you can use the remote controller’s [TUNER] but- ton to select the band.

To perform steps 1 and 2 on the AV receiver, press the [ZONE 2] button, and then use the Control- ler []/[ ] buttons within five seconds.

The name of the selected Zone 2 source appears on the display.

	an input source is selected, check if it’s connected to
	an analog input.
•	Since the Zone 2 function and the REC OUT outputs
	use the same circuitry, if the [Rec Out] function is
	used, Zone 2 will be turned off.
• While Zone 2 is being used, listening modes that need
	surround speakers are unavailable.
•	While Zone 2 is on,	functions will not work.
• You can’t select different radio stations for Zone 2 and
	the main room. For example, if you an FM station for
	the main room, that station will also be used in Zone 2.

66