RIDGID SP-500, SP500A, SP-330 Specific Safety Information, Description and Specifications, Service

Page 5

SP-330, SP-330D, SP-500, SP-500A Submersible Sump Pumps

Service

!WARNING

•The motor is oil filled and sealed for cooler run- ning. Allow 2 hours for the motor to cool before servicing. Hot oil is under pressure and could result in severe burns.

•Pump service must be performed only by qual- ified repair personnel. Service or maintenance performed by unqualified repair personnel could result in injury and may void the warranty.

•When servicing a pump, use only identical replacement parts. Follow instructions in the Maintenance Section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electrical shock or injury.

NOTE! Disassembly of the motor will void warranty.

Specific Safety Information

!WARNING Risk of electric shock. This pump is supplied with a grounding-type plug. To reduce risk of electric shock be certain that it is connect- ed only to a properly grounded, grounding-type receptacle that is protected by a GFCI.

For your own safety, before assembling and operating this unit, read this operators manual carefully and com- pletely. Learn the operation, application, and potential hazards peculiar to this unit.

Call the Ridge Tool Company, Technical Services Department at (800) 519-3456 if you have any ques- tions.

Submersible Pump Safety

!DANGER

•Do not use to pump flammable or explosive flu- ids such as gasoline, fuel oil, kerosene, sol- vents, thinners etc. Do not use in a flammable and/or explosive atmosphere. Pump should only be used to pump clear water. Improper use could result in personal injury and/or death.

!WARNING

•If there is water or moisture on the floor or

ground near the pump, do not walk on wet area until all power is turned off. If the shut-off box is in the basement, call an electrician. Failure to follow this warning could result in fatal electrical shock.

•Always disconnect the power source before attempting to install, service, relocate, or main- tain the pump. Never handle a pump or pump motor with wet hands or when standing on wet or damp surface or in water. Failure to follow this warning could result in personal injury and/or death.

•Pump motor is equipped with automatic reset- ting thermal protector that could restart unex- pectedly. Disconnect power source when servic- ing pump.

•Do not modify float or position float switch so that pump will operate continuously. Pump is not designed for continuous operation, this will reduce performance and life of the pump.

•Do not hang pump by handle for permanent installation. This minimizes twisting which can lead to damage during pump operations.

Description and Specifications

Description

The submersible pump is designed for home sump operations only. The unit is equipped with an 8 foot, 3- prong grounding type power cord. The motor has an automatic reset thermal protector to prevent burnouts due to overloading or clogging. A float activated switch provides automatic operation to maintain water level between factory preset points.

NOTICE This pump is not designed to handle salt water, brine, laundry discharge, or any other appli- cation which may contain caustic chemicals and/or for- eign materials. This pump is not suitable for use with aquatic life. Pump damage or failure could occur if used in these applications and will void the warranty.

NOTICE It is strongly recommended that a battery back-up system be used. Power outages, excessive water flow, G.F.C.I. tripping and primary pump wear can cause flooding. A battery back-up sys- tem reduces this risk. Contact your Ridge Tool distrib- utor.

Ridge Tool Company

3

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Submersible Sump Pumps Table of Contents 351403-005 4/04 SP-330, SP-330D, and SP-500, SP-500A Submersible Sump PumpsSafety Signal Words General Safety InformationElectrical Safety Personal SafetyDescription and Specifications Specific Safety InformationService Submersible Pump SafetyPump Installation Performance ChartSpecifications InstallationTesting Flood Alarm Models see figureWater Level Sensor Test ButtonFlood Alarm Models Maintenance InstructionsSuggested Part Replacement Schedule Service And RepairDescription Ridgid cat. # SP330 SP330D SP500 SP500A TroubleshootingSymptom Possible Causes Corrective Action Ridge Tool Company 351403-005 4/04 Table des matières Installation de la pompeInformations générales de sécurité Information de sécurité spécifiqueSécurité personnelle Aire de travailSécurité électrique Information de sécurité spécifique Description et SpécificationsSécurité de la pompe submersible Cette pompe n’est pasCourbe de performance Installation de la pompeTableau de performance SpécificationsBouton de test Ne placez pas directementLe flexible de décharge doit La tuyauterie extérieure doitSuggestions d’horaire de remplacement des pièces Modèles à alarme d’inondationService et réparation Instructions d’entretienLe haut et le bas Dépannage351403-005 4/04 Información general sobre seguridad ÍndiceInformación específica sobre seguridad Descripción y especificacionesPalabras de señales de seguridad Información general de seguridadÁrea de trabajo Seguridad eléctricaInformación específica de seguridad Descripción y especificacionesMantenimiento y reparación Aspectos de seguridad de la bomba sumergibleTabla de rendimiento Curva de rendimientoInstalación de la bomba EspecificacionesPruebas Modelos de alarmas contra inundaciones vea la figuraNo use la bomba directa La finalidad del uso de laServicio y reparación Modelos de alarmas contra inunda- cionesInstrucciones de mantenimiento Programa recomendado de recambio de piezasSíntoma Causas posibles Medida correctiva Corrección de fallasRidge Tool Company 351402-005 10/00 Ridge Tool CompanyRidge Tool Subsidiary Emerson Electric Co

SP-330D, SP-330, SP500A, SP-500 specifications

RIDGID is renowned for its innovative and high-performance plumbing and mechanical tools. Among its impressive lineup, the RIDGID SP-500, SP-330D, SP-330, and SP500A stand out as exceptional options for professionals in the field. These models cater to various needs with features and technologies designed for efficiency, reliability, and ease of use.

The RIDGID SP-500 is a powerful and versatile pipe cutter that features a robust design, allowing it to handle pipes up to 5 inches in diameter. Its durable construction ensures long-lasting performance, even in demanding environments. The SP-500 utilizes a patented anti-friction roller system, which enables smooth and precise cutting, minimizing the effort required. This model also incorporates an adjustable feed mechanism, allowing for quick adaptation to different pipe sizes while maintaining consistent cutting depth.

The SP-330D is designed specifically for handling drainage and vent piping. One of its standout characteristics is its compact design, which allows for easy maneuverability in tight spaces. The dual-cutting blade technology enhances cutting efficiency, which is essential for maintaining productivity on the job. This cutter can efficiently tackle various materials, from PVC to cast iron, making it a versatile addition to any toolkit.

In contrast, the RIDGID SP-330 offers similar performance but is aimed at a more extensive range of applications. It features a user-friendly design designed for maximum comfort and control. The ergonomic handle reduces hand fatigue during prolonged use. Like the SP-500, it includes the anti-friction roller system that provides superior cutting capabilities, helping professionals achieve precise results every time.

The SP500A is an advanced model equipped with the latest technologies to ensure optimal performance. The built-in LED indicator lights illuminate the work area, making it easier to see what you’re working on, even in low light conditions. Its lightweight construction is complemented by robust materials, ensuring that it remains durable while being easy to handle. The SP500A also features quick-release jaws for fast and efficient blade changes, which is a significant time-saver during work.

Overall, the RIDGID SP-500, SP-330D, SP-330, and SP500A offer a broad spectrum of essential features and technological advancements tailored for plumbing professionals. With their impressive cutting efficiencies, user-centric designs, and robust constructions, these tools exemplify the excellence that RIDGID is known for in the industry. Whether you need a precise cutter for PVC, cast iron, or other materials, these models provide reliability and functionality that can enhance productivity on every job site.
Top Page Image Contents