RIDGID SP-330, SP500A Flood Alarm Models see figure, Testing, Water Level Sensor, Test Button

Page 7
use an adapter.
! WARNING Support pump and piping when assembling and after installation. Failure to do so could cause piping to break or pump to fail, which could result in property damage and/or personal injury.
5. Set pump into sump. Locate the pump on a solid level surface.
NOTICE Do not place directly on clay, gravel, or any loose or sandy surfaces. These surfaces con- tain small stones or sand that may clog or damage the pump, which could result in pump failure causing flooding and property damage.
6. This pump has a 1-1/2” NPT discharge. If existing piping is 1-1/4” NPT, an adapter bushing (not included) may be used. Do not use piping that is less than 1-1/4” NPT. Piping that is too small will result in reduced output.
7. A check valve is required in the discharge line to prevent backflow when the pump shuts off. It is best to install the check-valve directly to the pump discharge. Thread a check valve into pump dis- charge.
Never cut off grounding prong or
! WARNING

SP-330, SP-330D, SP-500, SP-500A Submersible Sump Pumps

 

NOTICE

Be careful not to strip or cross-

 

 

thread. Do not use pipe joint sealant.

 

 

 

 

NOTICE

Flexible discharge hose is intended

 

 

for temporary use only. Rigid PVC or metal pipe is required for a permanent installation. If flexible dis- charge hose is temporarily used, make sure pump is secured in sump pit to prevent movement. Failure to secure pump could allow pump movement and cause switch interference and prevent pump from starting or stopping. This could result in flooding and property damage.

IMPORTANT! Make sure there is adequate room for float switch to move freely during operation. A 1” minimum is required.

8.Connect 1-1/4” diameter rigid pipe to rubber boot on check valve (not included). Reverse boot for 1- 1/2” diameter pipe. Tighten clamps.

9.Insert the pump cord plug directly into 115 volt grounded electrical outlet that is protected by Ground Fault Circuit Interrupter (GFCI) (Figure 1).

!WARNING When routing electrical cord protect cord from sharp objects, hot surfaces, oils, and chemi- cals. Do not kink cord, replace any damaged cord immediately.

Flood Alarm Models (see figure 3)

Water

Level

Sensor

Figure 3- Water Sensor

Test Button

TEST RESET

RESET TEST

Figure 4 – Alarm models

Unit should be plugged into outlet as shown in figure 4. Do not plug alarm box in upside down. Doing so may cause the pump to unplug. If the outlet is upside down, have a qualified electrician reposition the outlet before installing the unit.

Testing

1.Fill sump pit with water.

2.While the pump is draining the pit, verify that the discharge piping is carrying the water to a point at least 15 feet away from the foundation.

Ridge Tool Company

5

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Submersible Sump Pumps Table of Contents 351403-005 4/04 SP-330, SP-330D, and SP-500, SP-500A Submersible Sump PumpsPersonal Safety General Safety InformationSafety Signal Words Electrical SafetySubmersible Pump Safety Specific Safety InformationDescription and Specifications ServiceInstallation Performance ChartPump Installation SpecificationsTest Button Flood Alarm Models see figureTesting Water Level SensorService And Repair Maintenance InstructionsFlood Alarm Models Suggested Part Replacement ScheduleSymptom Possible Causes Corrective Action TroubleshootingDescription Ridgid cat. # SP330 SP330D SP500 SP500A Ridge Tool Company 351403-005 4/04 Information de sécurité spécifique Installation de la pompeTable des matières Informations générales de sécuritéSécurité électrique Aire de travailSécurité personnelle Cette pompe n’est pas Description et SpécificationsInformation de sécurité spécifique Sécurité de la pompe submersibleSpécifications Installation de la pompeCourbe de performance Tableau de performanceLa tuyauterie extérieure doit Ne placez pas directementBouton de test Le flexible de décharge doitInstructions d’entretien Modèles à alarme d’inondationSuggestions d’horaire de remplacement des pièces Service et réparationLe haut et le bas Dépannage351403-005 4/04 Descripción y especificaciones ÍndiceInformación general sobre seguridad Información específica sobre seguridadSeguridad eléctrica Información general de seguridadPalabras de señales de seguridad Área de trabajoAspectos de seguridad de la bomba sumergible Descripción y especificacionesInformación específica de seguridad Mantenimiento y reparaciónEspecificaciones Curva de rendimientoTabla de rendimiento Instalación de la bombaLa finalidad del uso de la Modelos de alarmas contra inundaciones vea la figuraPruebas No use la bomba directaPrograma recomendado de recambio de piezas Modelos de alarmas contra inunda- cionesServicio y reparación Instrucciones de mantenimientoSíntoma Causas posibles Medida correctiva Corrección de fallasRidge Tool Company Ridge Tool Subsidiary Emerson Electric Co Ridge Tool Company351402-005 10/00

SP-330D, SP-330, SP500A, SP-500 specifications

RIDGID is renowned for its innovative and high-performance plumbing and mechanical tools. Among its impressive lineup, the RIDGID SP-500, SP-330D, SP-330, and SP500A stand out as exceptional options for professionals in the field. These models cater to various needs with features and technologies designed for efficiency, reliability, and ease of use.

The RIDGID SP-500 is a powerful and versatile pipe cutter that features a robust design, allowing it to handle pipes up to 5 inches in diameter. Its durable construction ensures long-lasting performance, even in demanding environments. The SP-500 utilizes a patented anti-friction roller system, which enables smooth and precise cutting, minimizing the effort required. This model also incorporates an adjustable feed mechanism, allowing for quick adaptation to different pipe sizes while maintaining consistent cutting depth.

The SP-330D is designed specifically for handling drainage and vent piping. One of its standout characteristics is its compact design, which allows for easy maneuverability in tight spaces. The dual-cutting blade technology enhances cutting efficiency, which is essential for maintaining productivity on the job. This cutter can efficiently tackle various materials, from PVC to cast iron, making it a versatile addition to any toolkit.

In contrast, the RIDGID SP-330 offers similar performance but is aimed at a more extensive range of applications. It features a user-friendly design designed for maximum comfort and control. The ergonomic handle reduces hand fatigue during prolonged use. Like the SP-500, it includes the anti-friction roller system that provides superior cutting capabilities, helping professionals achieve precise results every time.

The SP500A is an advanced model equipped with the latest technologies to ensure optimal performance. The built-in LED indicator lights illuminate the work area, making it easier to see what you’re working on, even in low light conditions. Its lightweight construction is complemented by robust materials, ensuring that it remains durable while being easy to handle. The SP500A also features quick-release jaws for fast and efficient blade changes, which is a significant time-saver during work.

Overall, the RIDGID SP-500, SP-330D, SP-330, and SP500A offer a broad spectrum of essential features and technological advancements tailored for plumbing professionals. With their impressive cutting efficiencies, user-centric designs, and robust constructions, these tools exemplify the excellence that RIDGID is known for in the industry. Whether you need a precise cutter for PVC, cast iron, or other materials, these models provide reliability and functionality that can enhance productivity on every job site.
Top Page Image Contents