RIDGID SP500A Maintenance Instructions, Flood Alarm Models, Suggested Part Replacement Schedule

Page 8

SP-330, SP-330D, SP-500, SP-500A Submersible Sump Pumps

NOTICE The outside piping must be tilted downward to drain. This helps prevent debris from entering the discharge pipe, and also prevents trapped water from freezing which can damage the pump.

3.Install sump pit cover (not included) to prevent debris from clogging or damaging the pump.

Flood Alarm Models

Testing Alarm-(see figure 4)

NOTE! Disassembly of the motor will void the warran- ty.

Suggested Part Replacement Schedule

Replace pump switch every 2 years. See page 7 for Ridgid cat. #.

Replace float every 2 years. See page 7 for Ridgid cat. #.

Service And Repair

Press and hold test button until alarm sounds. If alarm does not activate after 3 seconds check and/or replace battery then repeat test.

Testing water level sensor–(see figure 3)

Alarm activates when water level raises the small white float. Test water level sensor operation by lifting it until alarm activates. A 3 to 5 second delay is normal.

Maintenance Instructions

!WARNING

•Always disconnect the electrical supply or unplug the pump before attempting to install, service, relocate, or perform any maintenance. If the power source is out of sight, lock and tag in the open (OFF) position to prevent unex- pected power application. Failure to do so could result in fatal electrical shock. Only a qualified technician should repair this unit. Improper repair could result in fatal electrical shock.

•The motor is oil filled and sealed for cooler running. Allow 2 hours for motor to cool before servicing. Hot oil under pressure could result in severe burns.

1.Check the operation of the Ground Fault Circuit Interrupter (GFCI) on a monthly basis.

2.Keep pump inlet clean and free of all foreign objects. Inspect at least once a year and clean sump as needed.

3.Check pump for proper operation monthly by filling sump with water until pump turns on.

4.Inspect all plumbing connections for any leaks or looseness monthly.

!WARNING

•Service and repair work on this pump must be per- formed by qualified repair personnel. Pump should be taken to a RIDGID Independent Authorized Service Center or returned to the factory. All repairs made by Ridge service facilities are war- ranted against defects in material and workman- ship.

•When servicing this pump, only identical replace- ment parts should be used. Failure to follow these steps may create a risk of flooding, property dam- age, fatal electrical shock, or other serious injury and may also void your warranty.

If you have any questions regarding the service or repair of this machine, call or write to:

Ridge Tool Company

Technical Service Department

400 Clark Street

Elyria, Ohio 44036-2023

Tel: (800) 519-3456

E-Mail: TechService@ridgid.com

For name and address of your nearest Independent Authorized Service Center, contact the Ridge Tool Company at (800) 519-3456 or http://www.ridgid.com

6

Ridge Tool Company

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Submersible Sump Pumps Table of Contents SP-330, SP-330D, and SP-500, SP-500A Submersible Sump Pumps 351403-005 4/04General Safety Information Safety Signal WordsElectrical Safety Personal SafetySpecific Safety Information Description and SpecificationsService Submersible Pump SafetyPerformance Chart Pump InstallationSpecifications InstallationFlood Alarm Models see figure TestingWater Level Sensor Test ButtonMaintenance Instructions Flood Alarm ModelsSuggested Part Replacement Schedule Service And RepairDescription Ridgid cat. # SP330 SP330D SP500 SP500A TroubleshootingSymptom Possible Causes Corrective Action Ridge Tool Company 351403-005 4/04 Installation de la pompe Table des matièresInformations générales de sécurité Information de sécurité spécifiqueSécurité personnelle Aire de travailSécurité électrique Description et Spécifications Information de sécurité spécifiqueSécurité de la pompe submersible Cette pompe n’est pasInstallation de la pompe Courbe de performanceTableau de performance SpécificationsNe placez pas directement Bouton de testLe flexible de décharge doit La tuyauterie extérieure doitModèles à alarme d’inondation Suggestions d’horaire de remplacement des piècesService et réparation Instructions d’entretienDépannage Le haut et le bas351403-005 4/04 Índice Información general sobre seguridadInformación específica sobre seguridad Descripción y especificacionesInformación general de seguridad Palabras de señales de seguridadÁrea de trabajo Seguridad eléctricaDescripción y especificaciones Información específica de seguridadMantenimiento y reparación Aspectos de seguridad de la bomba sumergibleCurva de rendimiento Tabla de rendimientoInstalación de la bomba EspecificacionesModelos de alarmas contra inundaciones vea la figura PruebasNo use la bomba directa La finalidad del uso de laModelos de alarmas contra inunda- ciones Servicio y reparaciónInstrucciones de mantenimiento Programa recomendado de recambio de piezasCorrección de fallas Síntoma Causas posibles Medida correctivaRidge Tool Company 351402-005 10/00 Ridge Tool CompanyRidge Tool Subsidiary Emerson Electric Co

SP-330D, SP-330, SP500A, SP-500 specifications

RIDGID is renowned for its innovative and high-performance plumbing and mechanical tools. Among its impressive lineup, the RIDGID SP-500, SP-330D, SP-330, and SP500A stand out as exceptional options for professionals in the field. These models cater to various needs with features and technologies designed for efficiency, reliability, and ease of use.

The RIDGID SP-500 is a powerful and versatile pipe cutter that features a robust design, allowing it to handle pipes up to 5 inches in diameter. Its durable construction ensures long-lasting performance, even in demanding environments. The SP-500 utilizes a patented anti-friction roller system, which enables smooth and precise cutting, minimizing the effort required. This model also incorporates an adjustable feed mechanism, allowing for quick adaptation to different pipe sizes while maintaining consistent cutting depth.

The SP-330D is designed specifically for handling drainage and vent piping. One of its standout characteristics is its compact design, which allows for easy maneuverability in tight spaces. The dual-cutting blade technology enhances cutting efficiency, which is essential for maintaining productivity on the job. This cutter can efficiently tackle various materials, from PVC to cast iron, making it a versatile addition to any toolkit.

In contrast, the RIDGID SP-330 offers similar performance but is aimed at a more extensive range of applications. It features a user-friendly design designed for maximum comfort and control. The ergonomic handle reduces hand fatigue during prolonged use. Like the SP-500, it includes the anti-friction roller system that provides superior cutting capabilities, helping professionals achieve precise results every time.

The SP500A is an advanced model equipped with the latest technologies to ensure optimal performance. The built-in LED indicator lights illuminate the work area, making it easier to see what you’re working on, even in low light conditions. Its lightweight construction is complemented by robust materials, ensuring that it remains durable while being easy to handle. The SP500A also features quick-release jaws for fast and efficient blade changes, which is a significant time-saver during work.

Overall, the RIDGID SP-500, SP-330D, SP-330, and SP500A offer a broad spectrum of essential features and technological advancements tailored for plumbing professionals. With their impressive cutting efficiencies, user-centric designs, and robust constructions, these tools exemplify the excellence that RIDGID is known for in the industry. Whether you need a precise cutter for PVC, cast iron, or other materials, these models provide reliability and functionality that can enhance productivity on every job site.
Top Page Image Contents