Shindaiwa 82052, SV212 manual Air filter, Fuel filter

Page 17

Air filter

Level 1.

Tools required: 25-50 mm (1-2 in.) cleaning brush.

NOTE

Clean daily.

1. Close choke (Cold Start Position [ ]). This prevents dirt from

entering the carburetor throat when the air filter is removed. Brush accumulated dirt from air cleaner area.

2.Remove air filter cover. Brush dirt from inside cover.

3.Remove air filter and lightly brush debris from filter. Replace filter if it is damaged, fuel soaked, very dirty, or the rubber sealing edges are deformed.

4.If filter can be reused, be certain it:

•Fits tightly in the air filter cavity.

•Is installed with the original side out.

5.Install air filter cover.

Fuel filter

Level 1.

Tools required: 200-250 mm (8-10 in.) length of wire with one end bent into a hook. clean rag, funnel, and an approved fuel container.

danger

Fuel is VERY flammable. Use extreme care when mixing, storing, or handling.

1.Use a clean rag to remove loose dirt from around fuel cap and empty fuel tank.

2.Use the “fuel line hook” to pull the fuel line and filter from the tank.

3.Remove the filter from the line and install the new filter.

ENGLISH

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents SV212 Shredder VAC Operator’s manual Table of ContentsIntroduction Personal condition and safety equipment Safety Manual safety symbols and important informationInternational symbols Eye Protection Physical ConditionHand Protection Breathing ProtectionRead the Manuals Repetitive Stress InjuriesClear the Work Area Keep a Firm GripEquipment check EPA Phase 2 / C.A.R.B. TierEmission Control Product Emission DurabilityDescription Located on blower housingContents Install Vacuum Tube and Bag Assembly Install Blower PipesAssembly Blower applicationFuel OperationHandling Fuel Fuel RequirementsMixing Instructions MetricStarting cold engine Throttle Trigger/Throttle Position Lever Starting warm engineStopping engine Blower operation Shredder Vac operation Problem Cause RemedyShredder Vac troubleshooting Skill level MaintenanceMaintenance intervals Fuel filter Air filterCooling system Cleaning GrillSpark plug Exhaust system Cleaning Cylinder FinsSpark Arrestor Screen Shredder blade Cylinder Exhaust PortDebris bag Parts Required NoneCarburetor adjustment High Altitude AdjustmentTroubleshooting Chart TroubleshootingStorage Long Term Storage Over 30 DaysModel SV212 Hand Held SpecificationsOwners Warranty Responsibilities Manufacturers Warranty CoverageWhat does this Warranty COVER? HOW will a Covered Part be CORRECTED?English English Shindaiwa Inc Shindaiwa Corporation 11975 S.W. Herman Rd Aspirador Triturador SV212 Tabla de materias IntroducciónEl manual del operador Condición personal y equipos de seguridad Símbolos internacionalesProtección de los ojos Condición físicaProtección de las manos Protección respiratoriaPeligro Lesiones debidas a esfuerzos repetitivosControl de emisiones Fase 2 de EPA / Nivel III de C.A.R.BEquipos Descripción Cubierta del sopladorContenido Instale el conjunto de tubo de vacío y bolsa Instale los tubos del sopladorMontaje Aplicación del sopladorCombustible OperaciónImportante Requisitos del combustibleManipulación del combustible Arranque del motor en frío Gatillo del acelerador Arranque con el motor calienteParada del motor Operación del soplador Operación del aspirador triturador Problema del aspirador trituradorNivel de habilidad MantenimientoIntervalos de mantenimiento ¡IMPORTANTEFiltro de combustible Filtro de aireSistemas de enfriamiento Limpieza de la parrillaBujía Sistema de escape Limpieza de las aletas del cilindroRejilla del apagachispas Hoja desmenuzadora Orificio de escape del cilindroBolsa de residuos Piezas necesarias NingunaAjuste del carburador Rodaje del motorAjuste de altitud elevada Localización y reparación de fallas Almacenamiento Almacenamiento a largo plazo más de 30 díasEspecificaciones California Tier III Emissions Defect Warranty EN Relacionados CON LAS Emisiones EPA PhaseRelacionados CON Emisiones EPA Phase 2 / California Pequeños Motores DE ExterioresNotas SP27 Shindaiwa Inc Shindaiwa Corporation Aspirateur Broyeur SV212 Table des matières Le manuel d’utilisationAvertissement Sécurité Symboles de sécurité et informations importantesProtection des yeux Condition physiqueProtection des mains Protection des voies respiratoiresLisez les manuels Microtraumatismes répétésDégagez la zone de travail Garder une bonne priseEquipment EPA Phase 2/ C.A.R.B. TierContrôle des émissions Durabilité DU Contrôle DES ÉmissionsCorps de la soufflante Contenu Installation du tube d’aspiration et du sac Installation des tubes de soufflanteAssemblage SoufflanteCarburant UtilisationManipulation du carburant Spécifications pour le carburantDémarrage dun moteur froid Gâchette des gaz Démarrage dun moteur chaudArret du moteur Utilisation de la soufflante Dépannage de la aspirateur broyeur Utilisation de la aspirateur broyeurIntervalles dentretien EntretienNiveaux de difficulte Filtre a carburant Fitlre à airPièces nécessaires BougieSystème de refroidissement Système déchappement Pare-étincellesLame de déchiquetage Lumière d’échappement du cylindreSac à débris Pièces nécessaires AucuneRéglage du carburateur Rodage du moteurRéglage pour haute altitude Dépannage Remisage Remisage à long terme plus de 30 joursModele SV212 à main CaractéristiquesResponsabilités DU Propriétaire À L’ÉGARD DE LA Garantie Couverture DE LA Garantie DES FabricantsCE QUE Couvre Cette Garantie EN CAS DE Pièce DéfectueuseRemarques FR27

82052, SV212 specifications

The Shindaiwa SV212,82052 is a powerful and versatile piece of equipment designed to meet the demands of landscaping professionals and enthusiasts alike. This advanced model combines cutting-edge technology and robust construction to deliver outstanding performance and reliability.

One of the notable features of the SV212,82052 is its high-performance engine. Engineered for efficient fuel consumption and lower emissions, the engine provides ample power to tackle a variety of tasks, from trimming and edging to landscaping and brush clearing. Its two-stroke engine design allows for a lightweight construction, making it easy to maneuver and operate for extended periods without causing undue fatigue.

The unit is equipped with an advanced vibration-dampening system that significantly reduces operator fatigue. This technology absorbs vibration during operation, enhancing comfort and improving control when working on extended jobs. This feature is particularly useful for professionals who require precision and endurance while completing landscaping projects.

In terms of functionality, the SV212,82052 features an adjustable cutting height that allows users to customize their work according to specific needs. This versatility means it can handle different types of vegetation effortlessly, from fine grass to thicker brush. The precision-engineered cutting blades ensure a clean and efficient cut every time, promoting a healthier lawn and garden.

Durability is another key characteristic of the Shindaiwa SV212,82052. Constructed from high-quality materials, this equipment is built to withstand the rigors of daily use in various environments. Its robust design resists wear and tear, ensuring that it will last through countless landscaping projects without compromising performance.

User-friendly controls enhance the overall experience as well. The easy-start mechanism minimizes the effort required to start the engine, allowing for quick and efficient operation. Additionally, the unit’s lightweight design means that even less-experienced users can handle it with confidence.

Overall, the Shindaiwa SV212,82052 combines performance, comfort, and durability to serve as an invaluable tool for anyone involved in landscaping. Whether for professional or personal use, this advanced machine is designed to make yard work more efficient and manageable while ensuring exceptional results. With its innovative technologies and thoughtful design, the SV212,82052 stands out as a top choice in its category.
Top Page Image Contents