Shindaiwa SV212, 82052 manual EPA Phase 2 / C.A.R.B. Tier, Equipment check, Emission Control

Page 6

ENGLISH

Equipment check

WARNING

Use only Shindaiwa approved attachments. Serious injury may result from the use of a non-approved attachment combination. Shindaiwa, Inc. will not be responsible for the failure of cutting devices, attachments or accessories which have not been tested and approved by Shindaiwa. Read and comply with all safety instructions listed in this manual and safety manual.

•Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed.

•Inspect fuel lines, tank and area around carburetor for fuel leaks. DO NOT operate unit if leaks are found.

•Do not use blower if any part is missing or damaged.

•Have repairs done only by an authorized Shindaiwa Service dealer.

•Do not use any attachment, accessory or replacement part unless it is recommended in this Operator's Manual.

WARNING

Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings.

•ALWAYS stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit.

•DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit.

•NEVER reach into any opening while the engine is running. Moving parts may not be visible through openings.

Emission Control

EPA Phase 2 / C.A.R.B. TIER III

The emission control system for the engine is EM/TWC (Engine Modification and 3-way Catalyst) and for the fuel tank the Control System is EVAP (Evaporative Emissions). Evaporative emission may be applicable to California models only.

IMPORTANT ENGINE INFORMATION

ENGINE FAMILY: 7EHXS.0214EKG DISPLACEMENT: 21.2 cc

EMISSION COMPLIANCE PERIOD : 300 HRS.

THIS ENGINE MEETS U.S. EPA PH2 EXH AND 2007 AND

LATER CALIFORNIA EXH AND EVAP EMISSION REGULA-

TIONS FOR S.O.R.E.. REFER TO OWNER'S MANUAL FOR

MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS.

An Emission Control Label is located on the engine. (This is an EXAMPLE ONLY; information on label varies by engine FAMILY).

PRODUCT EMISSION DURABILITY

The 300 hour emission durability period is the time span selected by the manufacturer certifying the engine emis- sions output meets applicable emissions regulations, provided that approved maintenance procedures are followed as listed in the Maintenance Section of this manual.

Page 5 Page 7
Image 6
Page 5 Page 7
Contents SV212 Shredder VAC Table of Contents IntroductionOperator’s manual Safety Manual safety symbols and important information International symbolsPersonal condition and safety equipment Hand Protection Physical ConditionEye Protection Breathing ProtectionClear the Work Area Repetitive Stress InjuriesRead the Manuals Keep a Firm GripEmission Control EPA Phase 2 / C.A.R.B. TierEquipment check Product Emission DurabilityLocated on blower housing DescriptionContents Assembly Install Blower PipesInstall Vacuum Tube and Bag Assembly Blower applicationOperation FuelMixing Instructions Fuel RequirementsHandling Fuel MetricStarting cold engine Starting warm engine Stopping engineThrottle Trigger/Throttle Position Lever Blower operation Problem Cause Remedy Shredder Vac troubleshootingShredder Vac operation Maintenance Maintenance intervalsSkill level Air filter Fuel filterCleaning Grill Spark plugCooling system Cleaning Cylinder Fins Spark Arrestor ScreenExhaust system Debris bag Cylinder Exhaust PortShredder blade Parts Required NoneHigh Altitude Adjustment Carburetor adjustmentTroubleshooting Troubleshooting ChartLong Term Storage Over 30 Days StorageSpecifications Model SV212 Hand HeldWhat does this Warranty COVER? Manufacturers Warranty CoverageOwners Warranty Responsibilities HOW will a Covered Part be CORRECTED?English English Shindaiwa Inc Shindaiwa Corporation 11975 S.W. Herman Rd Aspirador Triturador SV212 Introducción El manual del operadorTabla de materias Símbolos internacionales Condición personal y equipos de seguridadProtección de las manos Condición físicaProtección de los ojos Protección respiratoriaLesiones debidas a esfuerzos repetitivos PeligroFase 2 de EPA / Nivel III de C.A.R.B EquiposControl de emisiones Cubierta del soplador DescripciónContenido Montaje Instale los tubos del sopladorInstale el conjunto de tubo de vacío y bolsa Aplicación del sopladorOperación CombustibleRequisitos del combustible Manipulación del combustibleImportante Arranque del motor en frío Arranque con el motor caliente Parada del motorGatillo del acelerador Operación del soplador Problema del aspirador triturador Operación del aspirador trituradorIntervalos de mantenimiento MantenimientoNivel de habilidad ¡IMPORTANTEFiltro de aire Filtro de combustibleLimpieza de la parrilla BujíaSistemas de enfriamiento Limpieza de las aletas del cilindro Rejilla del apagachispasSistema de escape Bolsa de residuos Orificio de escape del cilindroHoja desmenuzadora Piezas necesarias NingunaRodaje del motor Ajuste de altitud elevadaAjuste del carburador Localización y reparación de fallas Almacenamiento a largo plazo más de 30 días AlmacenamientoEspecificaciones Relacionados CON Emisiones EPA Phase 2 / California Relacionados CON LAS Emisiones EPA PhaseCalifornia Tier III Emissions Defect Warranty EN Pequeños Motores DE ExterioresNotas SP27 Shindaiwa Inc Shindaiwa Corporation Aspirateur Broyeur SV212 Le manuel d’utilisation Table des matièresSécurité Symboles de sécurité et informations importantes AvertissementProtection des mains Condition physiqueProtection des yeux Protection des voies respiratoiresDégagez la zone de travail Microtraumatismes répétésLisez les manuels Garder une bonne priseContrôle des émissions EPA Phase 2/ C.A.R.B. TierEquipment Durabilité DU Contrôle DES ÉmissionsCorps de la soufflante Contenu Assemblage Installation des tubes de soufflanteInstallation du tube d’aspiration et du sac SoufflanteUtilisation CarburantSpécifications pour le carburant Manipulation du carburantDémarrage dun moteur froid Démarrage dun moteur chaud Arret du moteurGâchette des gaz Utilisation de la soufflante Utilisation de la aspirateur broyeur Dépannage de la aspirateur broyeurEntretien Niveaux de difficulteIntervalles dentretien Fitlre à air Filtre a carburantBougie Système de refroidissementPièces nécessaires Pare-étincelles Système déchappementSac à débris Lumière d’échappement du cylindreLame de déchiquetage Pièces nécessaires AucuneRodage du moteur Réglage pour haute altitudeRéglage du carburateur Dépannage Remisage à long terme plus de 30 jours RemisageCaractéristiques Modele SV212 à mainCE QUE Couvre Cette Garantie Couverture DE LA Garantie DES FabricantsResponsabilités DU Propriétaire À L’ÉGARD DE LA Garantie EN CAS DE Pièce DéfectueuseRemarques FR27

82052, SV212 specifications

The Shindaiwa SV212,82052 is a powerful and versatile piece of equipment designed to meet the demands of landscaping professionals and enthusiasts alike. This advanced model combines cutting-edge technology and robust construction to deliver outstanding performance and reliability.

One of the notable features of the SV212,82052 is its high-performance engine. Engineered for efficient fuel consumption and lower emissions, the engine provides ample power to tackle a variety of tasks, from trimming and edging to landscaping and brush clearing. Its two-stroke engine design allows for a lightweight construction, making it easy to maneuver and operate for extended periods without causing undue fatigue.

The unit is equipped with an advanced vibration-dampening system that significantly reduces operator fatigue. This technology absorbs vibration during operation, enhancing comfort and improving control when working on extended jobs. This feature is particularly useful for professionals who require precision and endurance while completing landscaping projects.

In terms of functionality, the SV212,82052 features an adjustable cutting height that allows users to customize their work according to specific needs. This versatility means it can handle different types of vegetation effortlessly, from fine grass to thicker brush. The precision-engineered cutting blades ensure a clean and efficient cut every time, promoting a healthier lawn and garden.

Durability is another key characteristic of the Shindaiwa SV212,82052. Constructed from high-quality materials, this equipment is built to withstand the rigors of daily use in various environments. Its robust design resists wear and tear, ensuring that it will last through countless landscaping projects without compromising performance.

User-friendly controls enhance the overall experience as well. The easy-start mechanism minimizes the effort required to start the engine, allowing for quick and efficient operation. Additionally, the unit’s lightweight design means that even less-experienced users can handle it with confidence.

Overall, the Shindaiwa SV212,82052 combines performance, comfort, and durability to serve as an invaluable tool for anyone involved in landscaping. Whether for professional or personal use, this advanced machine is designed to make yard work more efficient and manageable while ensuring exceptional results. With its innovative technologies and thoughtful design, the SV212,82052 stands out as a top choice in its category.
Top Page Image Contents