Eclipse Combustion 5600, VeriFlame Single Burner Monitoring System Internal Fault

Page 40

 

 

Table 9.2 Remote Display Diagnostic Messages (continued)

 

 

MESSAGE

TYPE

 

EXPLANATION

 

 

 

 

 

 

 

 

 

 

 

 

UNSAFE FLAME ON

Hold

 

Flame signal—actual, induced, or runaway scanner—is detected be-

 

 

 

 

 

 

fore start-up or after shutdown. The fan is energized. If the cause is

 

 

 

 

 

 

corrected within 30 seconds, as in afterburn, the control will turn

 

 

 

 

 

 

off the fan and continue the sequence.

 

 

 

 

 

 

 

 

 

UNSAFE FLAME ON

Lockout

 

Same conditions as above, except the cause has not been corrected

 

 

XX:XX:XX LOCKOUT

 

 

 

within 30 seconds, resulting in a lockout and the alarm being energized.

 

 

 

 

 

 

 

 

 

UNSAFE–FLM–PURGE

Hold

 

For purge & modulation models: Flame signal—actual, induced,

 

 

 

 

 

 

or runaway scanner—is detected during the selected purge time

 

 

 

 

 

 

period. The fan is energized. If the cause is corrected within 30 sec-

 

 

 

 

 

 

onds, as in afterburn, the control will turn off the fan and continue

 

 

 

 

 

 

the sequence.

 

 

 

 

 

 

 

 

 

UNSAFE–FLM–PURGE

Lockout

 

For purge & modulation models: Same conditions as above,

 

 

XX:XX:XX LOCKOUT

 

 

 

except the cause has not been corrected within 30 seconds, resulting

 

 

 

 

 

 

in a lockout and the alarm being energized.

 

 

 

 

 

 

 

 

 

V–INTERNAL FAULT

Lockout

 

Internal control failure; replace controller.

 

 

XX:XX:XX LOCKOUT

 

 

 

 

 

 

 

 

 

 

 

 

 

WATCHDOG FAIL

Lockout

 

Internal control failure; replace controller.

 

 

XX:XX:XX LOCKOUT

 

 

 

 

 

 

 

 

 

 

 

 

 

XXXXXXX

Status

 

In combination with other messages, shows the control is in the

 

 

XXXXXTESTXX

 

 

 

minimum pilot test mode.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Eclipse Veri-Flame Instruction Manual 818 -2/02

40

Image 40
Contents VeriFlame Single Burner Monitoring System Copyright Disclaimer Notice Liability Warranty About this manual Audience Scope Document ConventionsHOW to GET Help Table of Contents Page LED Status & Conditions for No Purge Models Table Introduction Product DescriptionSpecifications SpecificationsIntroduction Veri-Flame Unit/All Models DimensionsVeri-Flame Bases/Purge & No Purge Models Remote Display Model Number 5602-DB Veri-Flame/Modulating Model with Base Model NumberRemote Display Model Number 5602-DBP DIP Switch Selection Modulation & Purge DIP Switch SettingsDIP Switch Location Interlocks and Limit Switch Input Terminal Combustion Air Introduction Standard FeaturesMain Fuel Valve Closed Switch Terminal Function SummaryTest Mode Run Mode Seconds Optional Features Status Lights PUSH-BUTTONSystem Installation Ignition Wiring Low Fire Input High Purge Input Remote Reset Remote Display & Power SupplyNo Purge and Purge Wiring Diagrams No Purge Models Typical Connections For All Models Purge and No Purge Bases Modulating BaseSequence Diagrams InputsSensor Installation Sensor Wiring Flame RodsScanners Scanner Sighting Considerations Flame Rod PositionTest Procedures Flame Signal Strength Minimum Pilot TestPilot Flame Failure Test Main Flame FailureTest Spark Sighting Test Limits & Interlock TestsMonthly Checklist Yearly Checklist Maintenance &TroubleshootingIntroduction Maintenance Troubleshooting Problem Possible Cause SolutionLED Status LED Status & Conditions forVeri-Flame Purge Models AIR FailureLED Status & Conditions forVeri-Flame Modulation Models Auto Interlocks ClosedRemote Display Messages Power on Veri-Flame Operating SequenceYES no YES Burner Shutdown AIR Failure Remote Display Diagnostic Messages Xxxxxx Lockout Pilot onInternal Fault Appendix Conversion FactorsMetric to English Metric to MetricIllustrated Parts List Pos Model Part Category Description Number

5600, VeriFlame Single Burner Monitoring System specifications

The Eclipse Combustion VeriFlame Single Burner Monitoring System, model 5600, represents a significant advancement in the field of combustion management technology. Designed to provide enhanced monitoring and control of burner operations, the VeriFlame system is equipped with state-of-the-art features that ensure optimal efficiency, safety, and performance in a variety of industrial applications.

One of the main features of the VeriFlame 5600 is its advanced flame detection technology, which employs efficient optical sensors to monitor flame presence and stability continuously. This feature enables the system to provide real-time feedback, ensuring that burners operate within specified parameters and respond swiftly to any fluctuations. The system’s intelligent analytics can easily discern between normal operational conditions and potential hazards, enhancing safety and reducing the risk of unsafe operation.

The VeriFlame system is also known for its versatile communication capabilities, featuring multiple connectivity options. The unit can integrate seamlessly with existing plant control systems using industry-standard protocols such as Modbus or Profibus. This interoperability allows for comprehensive data sharing and centralized control of multiple burner systems from a single interface, streamlining operations and improving operator efficiency.

Another notable characteristic of the Eclipse Combustion VeriFlame is its user-friendly interface. The system comes with an intuitive graphical display that provides operators with critical operational data, including flame quality, burner status, and diagnostic information. This straightforward interface facilitates quick decision-making and troubleshooting, minimizing downtime and enhancing the overall operational efficiency of the burner system.

The 5600 model also offers robust diagnostic capabilities, allowing for proactive maintenance and reduced unexpected failures. It features built-in self-check routines and historical data logging, which provide valuable insights into system performance over time. These diagnostic tools empower operators to identify and address potential issues before they escalate, thereby reducing maintenance costs and enhancing the longevity of the burner components.

Moreover, the VeriFlame system is designed with flexibility in mind, accommodating various burner types and fuel sources. This adaptability makes it suitable for use in a wide range of industries, including oil and gas, power generation, and manufacturing.

In conclusion, the Eclipse Combustion VeriFlame Single Burner Monitoring System 5600 stands out due to its advanced flame detection, versatile communication options, user-friendly interface, robust diagnostics, and flexibility. Together, these features make it an essential tool for optimizing combustion processes, enhancing safety, and improving overall operational efficiency in industrial environments.