Greenheck Fan 470654 manual Assembly, Figure C

Page 9
Figure B

Assembly

1.Position platform base as shown below in Figure A with the grate side up.

2.Attach the left and right handrails to the platform base with (3/8 in. x 3/4 in.) hex head bolts and (3/8 in.) hex nuts as shown in Figure A. Use six bolts and nuts on each rail.

3.Raise the platform base, grate side up, with a crane or forklift.

4.Attach legs to the slots on sides of platform base with two (3/8 in. x 3/4 in.) hex head bolts and (3/8 in.) hex nuts.

6.Facing the control panel side of the unit, find the center of the housing and drill a (7/16 in.) hole through the housing and support stand (3/8 in.) above the form line as shown in Figure C.

3/8 inch

Form Line

12 inches 12 inches

Figure C

Next, drill two more (7/16 in.) holes through the housing and support stand (12 in.) on either side of the center hole, (3/8 in.) above the form line. These holes are used to attach the platform base to the unit.

7.Attach the service platform to the control panel side of the housing by inserting the three (3/8 in. x

1-1/2 in.) bolts of platform base into the three holes of the housing. Securely fasten with three (3/8 in.) hex nuts.

8.Level service platform if necessary by adjusting legs and then attach leg cross member with two (3/8 in. x 3/4 in.) hex head bolts and 3/8 in. hex head nuts.

9.Securely fasten all nuts and bolts. Make sure all nuts and bolts are tight.

10.Attach arm rails of service platform to the housing by first drilling a 5/16 in. hole through the housing at the attachment point as shown in Figure D. Secure arm rails to the housing with (3/8 in. x 1 in.) thread cutting screws. Be sure not to over-tighten screws.

11.Attach safety chains to the right hand rail, across the entryway. Assembly is complete.

Figure A

5.Fasten three (3/8 in. x 1-1/2 in.) hex head bolts into the side of the platform

base. Secure each bolt with two (3/8 in.) hex

head nuts placed back to back on each bolt as shown in Figure B. These bolts will be used to attach the platform base to the unit.

Attachment Points

for Step 11

Figure D

Model VSU Make-Up Air 9

®

Image 9
Contents Model VSU General Safety Information Installation, Operation and Maintenance ManualReceiving Inspection and Maintenance during StorageUnpacking HandlingTable of Contents Subassemblies Product OverviewOpen View Burner, Blower and Control Center SectionBurner Subassembly Control CenterDampers Installation Complete Installation Installation of Optional Service PlatformService Platform Material List Figure C AssemblyInstallation of Electrical Wiring Installation of Direct Gas Piping Install Additional Regulator if RequiredDetermine the Supply Gas Requirements Installation of Building Pressure Control optional Start-Up Checklist Unit Model NumberCheck blower rotation Check for vibration Supply fan RPM Start-Up Blower Start-Up Direct Gas Check the Optional High and Low Gas Pressure SwitchesSet-Up Optional Components Check the Supply Gas PressureSet the Burner Air Pressure Differential Maximum firing rate adjustmentSet the Maximum Firing Rate Measuring the Pressure DropSet the Minimum Firing Rate Regulators and Modulating ValvesSet the Unit’s Operating Temperature Flame Signal Check Pilot IgnitionMaxitrol Series 44 9 Terminals The Maxitrol Operation VAV Units optional Variable Volume OperationSpeed ModulatingOperation Electrical Operation Recirculating Units optionalRecirculation Operation Electrical Sequence Exhaust Fan Contact S1 Closed optional3a. Heat Contact S4 Closed Pilot Ignition Flame Safeguard FSG Sequence3b. Heat Contact S4 Closed Direct Spark Heat Contact ClosedBlower Does Not Operate TroubleshootingMotor Overamps Too Much Airflow Insufficient AirflowExcessive Noise or Vibration Does not attempt to light No visible spark Heater Does Not Operate Pilot IgnitionAttempts to light, but no pilot visible spark Between 0.625 and 0.675 in. WC? Visible pilotHeater Does Not Operate Direct Spark Attempts to light, but no flame Visible spark Belt Drives Maintenance RoutineMotors WheelsMaintenance Fall Reference Typical Gas Train Layout with Direct Spark Ignition Fan Relay allows power to pass to energize motor starter Dirty Filter SwitchHeat Relay allows power to pass to heating controls Control Center LayoutMaintenance Log WarrantyDateTime AM/PM

470654 specifications

Greenheck Fan 470654 is a cutting-edge ventilation solution designed to meet the demanding requirements of commercial and industrial applications. Renowned for its reliability and efficiency, this fan model integrates advanced technologies and engineering to provide optimal air movement and control.

One of the standout features of the Greenheck Fan 470654 is its robust construction. Designed with high-quality materials, the fan promotes longevity and durability, making it suitable for use in tough environments. This fan features a heavy-gauge steel housing that minimizes vibration and enhances noise reduction, contributing to a quieter operation, a critical factor in maintaining a serene working environment.

The fan is equipped with a powerful motor that ensures efficient airflow, achieving high performance while consuming minimal energy. This energy efficiency is emphasized through the use of advanced motor technology, including variable frequency drive (VFD) compatibility. VFDs allow for precise control of the fan speed, enabling adjustments based on system demand, thus significantly reducing energy consumption and operating costs.

In terms of airflow performance, the Greenheck Fan 470654 is engineered to provide a high volume of air movement while maintaining static pressure. Its aerodynamic design minimizes resistance, enhancing overall efficiency. The fan is designed to operate across a range of static pressures, making it versatile for different applications, from commercial kitchens to large manufacturing facilities.

Additionally, the fan's installation is straightforward, thanks to its user-centric design. The model incorporates mounting brackets and options for various duct configurations, ensuring seamless integration into existing systems. Maintenance is also made easier with accessible components, allowing technicians to perform regular checks and upkeep without extensive downtime.

Safety features are a priority in the design of the Greenheck Fan 470654. It includes protective features such as thermal overload protection to prevent motor damage and extend operational life. The fan's design also adheres to industry standards and regulations, providing peace of mind for users.

In summary, the Greenheck Fan 470654 is a well-engineered solution that combines durability, efficiency, and advanced technology to deliver superior performance in ventilation applications. With its powerful motor, energy-saving capabilities, and ease of installation and maintenance, it stands out as a reliable choice for professionals seeking optimal airflow management.