Hearth and Home Technologies 6000TRSI-AUC manual Heat & Glo Quality Systems

Page 2

PLEASE READ THIS MANUAL BEFORE INSTALLING AND

USING THIS APPLIANCE.

MODEL 6000TRSI-AUC

IS AUSTRALIAN GAS ASSOCIATION APPROVED FOR NATURAL GAS OR PROPANE AS A BALANCED FLUE HEATER.

Refer to the appliance data plates for gas consump- tions and pressures.

Installation of this appliance should only be carried out by an authorized person in accordance with the manufacturers instructions. All relevant codes and regulations laid down by the gas fitting authorities, municipal building regulations, electrical wiring regu- lations, and the requirements of the AGA Gas In- stallation Code must be observed.

This appliance and its components are tested and safe when installed in accordance with this Installa- tion Manual. Report to your dealer any parts dam- aged in shipment, specifically check glass condi- tion. The gas logs and flue system components are in separate packages. Read all instructions before

starting installation and follow these instructions carefully during installation to ensure maximum ben- efit and safety. Failure to follow them will void your warranty and may present a fire hazard.

The Heat & Glo warranty will be voided by, and Heat

&Glo disclaims any responsibility for the following actions:

•Installation of any damaged heater or flue sys- tem component

•Modification of the heater or balanced flue sys- tem installation other than as instructed by Heat & Glo.

•Improper positioning of the gas logs or the glass door

•Installation and/or use of any component part not manufactured or approved by Heat & Glo, not withstanding any independent testing labo- ratory or other party approval of such compo- nent part or accessory.

IMPORTANT: Read all instructions carefully before starting installation. Failure to follow these installation instructions may result in a possible fire hazard and will void the warranty. Save this manual for future reference.

Heat & Glo, a brand of Hearth & Home Technologies, Inc.

Heat & Glo Quality Systems

20802 Kensington Blvd., Lakeville, MN 55044, USA

registered by SGS ICS

Copyright 2006 • Printed in U.S.A.

 

2

Heat & Glo • 6000TRSI-AUC • 2078-900 Rev. G • 12/06

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Installation and Operation Instructions Model 6000TRSI-AUCHeat & Glo Quality Systems Table of Contents Installation Instructions 476 686 31-5/8 803 174 126.9Clearance Requirements Rear FlueTop Flue Framing the Heater Clearances n mm Flue System Approvals and Installations 10.97m13.1 331mm 24 610mm ElbowsFlueing with One 90 Elbow +H 1 FT + H 1 FT 13 Flueing with three 90 elbows Flueing with Three 3 90 Elbows + H 1 FTFlueing Out the Rear Flue Flueing Out the Top FlueAssembling Flue Components Install Support Brackets Flue Termination Connecting the GAS Supply Must be Positioned SO That the Arrow is Pointing UPIgnition System Wiring Shock RiskBlower Fan Mantel Clearances Clearance to a mantelpiece is 12 inches 305mm. See FigureLOG Placement Instructions TabsHeat & Glo 6000TRSI-AUC 2078-900 Rev. G 12/06 Installer Testing Operating InstructionsOperating Cautions For Your Safety Read Before Lighting Instructions Safety & Lighting InformationPower Outage FAN OperationServicing and Maintenance Adjustments and Replacement Parts Removal of Components for ServiceParts Replacement Removal of Covers for ServicingMaintenance Tasks Inspect Maintenance TasksTroubleshooting Electronic Ignition SystemAdjust the air shutter at the base of the burner Log set assembly 6000TRSI-AUC6000TRSI-AUC GLA-6TRXILimited 10 Year Warranty Heat & GLO, a brand of Hearth & Home Technologies IncMelbourne
Top Page Image Contents