Hearth and Home Technologies 810-02901 (MBK) Base Plate Only Installation, Kit Includes See

Page 18

Castile Pellet Insert

 

R

 

 

D. Zero Clearance Trim Support (Cont’d)

T

Kit Includes: See Page 17

 

 

Tools Needed: Phillips head screwdriver

 

 

1.

Remove contents from box and lay on protective surface

 

 

to avoid scratching the paint.

 

 

2. Lay zero clearance front and sides face down. Bend the

 

 

tab down toward the inside.

 

Figure 18.4

3.

The side pieces are shipped flat. It is much easier to manually

 

 

flex the sides into a bowed position before installing.

 

4.

Lay 1 cast ring face up, which will become the bottom ring

 

 

when installed. Attach the 2 sides FIRST and then the front

 

 

piece. Figure 18.1.

 

L

5. Now turn the cast ring right side up and attach the top cast

 

 

ring . Figure 18.2.

 

 

6. Attach the zero clearance panel extensions. Figure 18.3

 

7. Attach cast footers. Figure 18.4.

 

 

8. Place the assembled zero clearance trim support under

 

 

the insert. Figure 18.5.

 

Figure 18.5

 

 

Sides

Base Plate Only Installation

 

InstallFirst

 

Parts Needed: (1) cast ring (2) base zero clearance panel

 

Install Front Last

OT

 

extensions. Discard balance of parts.

 

-

 

Bend top and bottom tabs toward inside

 

Tools Needed: Phillips head screwdriver

 

 

 

Figure 18.1

 

1. Attach base zero clearance panel extensions to cast

 

ring.

 

 

 

Turn right side up and attach top cast ring

Figure 18.2

Alignment

Hole

Zero Clearance Panel Extension

Figure 18.3

2. Place assembly under appliance.

Cast Trim Footer

Panel Leg

Zero Clearance

Panel Extension

Figure 18.6

Page 18

250-7251F

September 1, 2008

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Castile Pellet Insert 810-02901 MBK 810-03201 PMHCastile Pellet Insert Location Inside hopper on the topTable of Contents Mobile Home Approved Listing and Code ApprovalsAppliance Certification BTU & Efficiency Specifications Glass SpecificationsGetting Started Design, Installation & Location ConsiderationsFire Safety Appliance LocationCastile Pellet Insert Tools And Supplies Needed Inspect Appliance & Components and Pre-Use Check List3Dimensions and Clearances Appliance DimensionsShown Optional Outside Air Castile Pellet Insert Clearance To Combustibles, UL and ULC0mm Clearance To Exposed Section And Face Trim Inches MillimetersMinimum Opening for Masonry and Zero Clearance Fireplaces Castile Pellet Insert Masonry and Zero Clearance FireplacesFloor Protection Location Inches MillimetersStarter hole Mark area of floor to cut 4Vent Information Chimney and Exhaust ConnectionVenting Termination Requirements Pipe Selection Chart Castile Pellet Insert Equivalent Feet of PipeExample of 3 Elbow-Rear Vent Termination Calculation 5Venting Systems Castile Pellet Insert Full Reline With Outside Air Mobile Home Installation 6Mobile Home7Appliance Set-Up Top Vent InstallationRear Vent Installation Reversible Top or Rear Flue Adapter Leveling SystemAssembled View ItemDescriptionKit Includes See Base Plate Only InstallationCastile Pellet Insert Zero Clearance Trim Support Cont’d Piece. FigurePanel Set And Cast Trim Set Panel & Trim Set, EconoFour Piece Log Set Installation Top Log InstallationCastile Pellet Insert Thermostat Installation Operating Instructions Fuel Size And MaterialGeneral Operating Information Castile Pellet Insert Before Your First Fire Feed Rate AdjustmentFire Characteristics Starting Your First FireFrequently Asked Questions Castile Pellet Insert Iginition CyclesTroubleshooting SymptomPossible Cause Corrective Action Page Symptom Possible Cause Corrective Action 10Maintaining & Servicing Your Appliance Quick Reference Maintenance ChartCleaning or Inspection Frequency Daily Weekly Monthly YearlyAsh Removal from Firebox Remove Cast Sides for Cleaning & MaintenanceCleaning Firepot with Cleaning Rod & Firepot Scraper See Disposal of AshesCleaning Heat Exchanger Chambers & Drop Tube Cleaning Beneath Heat ExchangerCleaning the Exhaust Path Cleaning the Glass Cleaning the HopperCleaning Convection Blower Requires No Lubrication Cleaning Exhaust Blower Requires No LubricationHigh Ash Fuel Content Maintenance Door Gasket InspectionPreparing Firebox for Non-Burn Season Frequency Yearly Igniter Replacement Baffle & Brick Set Removal 35.1Re-installing Baffle & Brick Set Cont’d Component Function Snap Disc #1 Convection Blower 110F Vacuum SwitchWiring Harness See .1 below Snap Disc #2 Fuel Delivery Interrupt 250FCleaning Rods & Heat Exchanger Tubes Castile Pellet Insert Component LocationsCastile Pellet Insert Exploded Views Glass Size 11-5/8 wide x 17-1/4 highDescription Castile Pellet Insert Service Parts and Accessories Item # Part Description, Alphabetical Order Part NumberItem No Accessories, Alphabetical Order Item No ApplianceItem # Part Description, Alphabetical Order Castile Pellet Insert Service And Maintenance Log Date of Service Performed By Description of ServiceCastile Pellet Insert Service And Maintenance Log Cont’d Castile Pellet Insert Homeowner’s Notes Castile Pellet Insert Warranty Policy CONDITIONS, Exclusions & Limitation of LiabilityHearth & Home Technologies Limited Warranty Cont’d Castile Pellet Insert Telephone

CASTINS-CWL, CASTINS-CSB, 810-03201 (PMH), 810-02901 (MBK) specifications

Hearth and Home Technologies has made a significant mark in the hearth and home industry with a variety of innovative products, including models like the 810-02901 (MBK), 810-03201 (PMH), CASTINS-CSB, and CASTINS-CWL. These models reflect state-of-the-art design and engineering, ensuring comfort and efficiency in residential heating solutions.

The 810-02901 (MBK) model is designed primarily for modular design, allowing for easy installation and integration into various home architectures. This model features advanced combustion technology that maximizes fuel efficiency while minimizing emissions. It is equipped with an innovative air control system that provides users with precise control over flame height and heat output, enhancing the overall user experience. With features such as a large viewing area, the MBK model provides an attractive look while ensuring optimum safety.

The 810-03201 (PMH) model offers versatile heating options and an elegant design that fits seamlessly into modern interiors. This model is notable for its user-friendly interface, which enables users to control settings with ease. It also has a remarkable heat distribution system, allowing warmth to spread evenly throughout the space, reducing cold spots and enhancing comfort. Additionally, the PMH model is built with durable materials that withstand the test of time, making it a long-lasting investment for homeowners.

The CASTINS-CSB and CASTINS-CWL models represent the pinnacle of contemporary fireplace design with their cast iron construction, enhancing durability and offering superior heat retention. Both models feature intricate designs that not only elevate the aesthetic of any room but also provide effective heating solutions. With the CASTINS series, Hearth and Home Technologies emphasizes the importance of safety with features such as heat shields and advanced flue systems that ensure proper ventilation.

In summary, Hearth and Home Technologies' 810-02901 (MBK), 810-03201 (PMH), CASTINS-CSB, and CASTINS-CWL models are characterized by their innovative technology, elegant design, and efficient heating capabilities. These models cater to a variety of homeowner needs, providing comfort, efficiency, and safety while enhancing interior aesthetics. Whether you’re looking for a robust heating solution or an elegant focal point in your home, Hearth and Home Technologies offers durable and stylish options that stand out in any environment.
Top Page Image Contents