Hearth and Home Technologies CASTINS-CSB Four Piece Log Set Installation, Top Log Installation

Page 20

R

Castile Pellet Insert

G. Optional Log Set Placement Instructions

CAUTION

Logs are FRAGILE. Use extreme care when handling or cleaning logs.

Four Piece Log Set Installation

1.Open the hinged cast face and open the glass door assembly.

2.Positioning the logs.

Place the right rear log as shown. There is a notch in the bottom of the log for clearance for the thermocou- ple and thermocouple cover (ceramic protection tube).

Figure 20.1

Continue placing the last 3 logs around the firepot as show in Figures 20.2, 20.3 and 20.4. Be careful not to block the drop tube in the back of the firebox where pel- lets feed into the firepot.

Notch

Thermocouple

Cover

Figure 20.1

Drop Tube

Figure 20.2

NOTE:

Due to the abrasive nature of a pellet appliance fire, the logs are not covered under warranty. Any placement varia- tion other than shown here can cause excessive heat and shall void the appliance warranty.

Figure 20.3

Figure 20.4

Top Log Installation

Place the log over the firepot. The charred area on the log is turned toward the back, not the front.

The log will be about 2-1/2 inches (64mm) above the firepot when in place. It must rest on the 3 logs in a stable position to prevent it from falling into the firepot. Figure 20.5.

Figure 20.5

Page 20

250-7251F

September 1, 2008

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Castile Pellet Insert 810-02901 MBK 810-03201 PMHCastile Pellet Insert Location Inside hopper on the topTable of Contents Listing and Code Approvals Appliance Certification BTU & Efficiency SpecificationsMobile Home Approved Glass SpecificationsDesign, Installation & Location Considerations Fire SafetyGetting Started Appliance LocationCastile Pellet Insert Tools And Supplies Needed Inspect Appliance & Components and Pre-Use Check List3Dimensions and Clearances Appliance DimensionsCastile Pellet Insert Clearance To Combustibles, UL and ULC 0mm Clearance To Exposed Section And Face TrimShown Optional Outside Air Inches MillimetersCastile Pellet Insert Masonry and Zero Clearance Fireplaces Floor ProtectionMinimum Opening for Masonry and Zero Clearance Fireplaces Location Inches MillimetersStarter hole Mark area of floor to cut Venting Termination Requirements 4Vent InformationChimney and Exhaust Connection Example of 3 Elbow-Rear Vent Termination Calculation Pipe Selection ChartCastile Pellet Insert Equivalent Feet of Pipe 5Venting Systems Castile Pellet Insert Full Reline With Outside Air Mobile Home Installation 6Mobile HomeTop Vent Installation Rear Vent Installation7Appliance Set-Up Reversible Top or Rear Flue Adapter Leveling SystemAssembled View ItemDescriptionBase Plate Only Installation Castile Pellet Insert Zero Clearance Trim Support Cont’dKit Includes See Piece. FigurePanel Set And Cast Trim Set Panel & Trim Set, EconoFour Piece Log Set Installation Top Log InstallationCastile Pellet Insert Thermostat Installation General Operating Information Operating InstructionsFuel Size And Material Feed Rate Adjustment Fire CharacteristicsCastile Pellet Insert Before Your First Fire Starting Your First FireFrequently Asked Questions Castile Pellet Insert Iginition CyclesPossible Cause Corrective Action TroubleshootingSymptom Page Symptom Possible Cause Corrective Action Quick Reference Maintenance Chart Cleaning or Inspection10Maintaining & Servicing Your Appliance Frequency Daily Weekly Monthly YearlyRemove Cast Sides for Cleaning & Maintenance Cleaning Firepot with Cleaning Rod & Firepot ScraperAsh Removal from Firebox See Disposal of AshesCleaning the Exhaust Path Cleaning Heat Exchanger Chambers & Drop TubeCleaning Beneath Heat Exchanger Cleaning the Hopper Cleaning Convection Blower Requires No LubricationCleaning the Glass Cleaning Exhaust Blower Requires No LubricationPreparing Firebox for Non-Burn Season Frequency Yearly High Ash Fuel Content MaintenanceDoor Gasket Inspection Igniter Replacement Baffle & Brick Set Removal 35.1Re-installing Baffle & Brick Set Cont’d Component Function Vacuum Switch Wiring Harness See .1 belowSnap Disc #1 Convection Blower 110F Snap Disc #2 Fuel Delivery Interrupt 250FCleaning Rods & Heat Exchanger Tubes Castile Pellet Insert Component LocationsCastile Pellet Insert Exploded Views Glass Size 11-5/8 wide x 17-1/4 highDescription Castile Pellet Insert Service Parts and Accessories Item # Part Description, Alphabetical Order Part NumberItem # Part Description, Alphabetical Order Item No Accessories, Alphabetical OrderItem No Appliance Castile Pellet Insert Service And Maintenance Log Date of Service Performed By Description of ServiceCastile Pellet Insert Service And Maintenance Log Cont’d Castile Pellet Insert Homeowner’s Notes Castile Pellet Insert Warranty Policy CONDITIONS, Exclusions & Limitation of LiabilityHearth & Home Technologies Limited Warranty Cont’d Castile Pellet Insert Telephone

CASTINS-CWL, CASTINS-CSB, 810-03201 (PMH), 810-02901 (MBK) specifications

Hearth and Home Technologies has made a significant mark in the hearth and home industry with a variety of innovative products, including models like the 810-02901 (MBK), 810-03201 (PMH), CASTINS-CSB, and CASTINS-CWL. These models reflect state-of-the-art design and engineering, ensuring comfort and efficiency in residential heating solutions.

The 810-02901 (MBK) model is designed primarily for modular design, allowing for easy installation and integration into various home architectures. This model features advanced combustion technology that maximizes fuel efficiency while minimizing emissions. It is equipped with an innovative air control system that provides users with precise control over flame height and heat output, enhancing the overall user experience. With features such as a large viewing area, the MBK model provides an attractive look while ensuring optimum safety.

The 810-03201 (PMH) model offers versatile heating options and an elegant design that fits seamlessly into modern interiors. This model is notable for its user-friendly interface, which enables users to control settings with ease. It also has a remarkable heat distribution system, allowing warmth to spread evenly throughout the space, reducing cold spots and enhancing comfort. Additionally, the PMH model is built with durable materials that withstand the test of time, making it a long-lasting investment for homeowners.

The CASTINS-CSB and CASTINS-CWL models represent the pinnacle of contemporary fireplace design with their cast iron construction, enhancing durability and offering superior heat retention. Both models feature intricate designs that not only elevate the aesthetic of any room but also provide effective heating solutions. With the CASTINS series, Hearth and Home Technologies emphasizes the importance of safety with features such as heat shields and advanced flue systems that ensure proper ventilation.

In summary, Hearth and Home Technologies' 810-02901 (MBK), 810-03201 (PMH), CASTINS-CSB, and CASTINS-CWL models are characterized by their innovative technology, elegant design, and efficient heating capabilities. These models cater to a variety of homeowner needs, providing comfort, efficiency, and safety while enhancing interior aesthetics. Whether you’re looking for a robust heating solution or an elegant focal point in your home, Hearth and Home Technologies offers durable and stylish options that stand out in any environment.
Top Page Image Contents