Hearth and Home Technologies CASTINS-CWL Getting Started, Fire Safety, Appliance Location

Page 5

R

Castile Pellet Insert

2 Getting Started

A.Design, Installation & Location Considerations

1. Appliance Location

Consideration must be given to safety, convenience, traffic flow, and the fact that the appliance will need a chimney and chimney connector. It is a good idea to plan your installation on paper, using exact measurements for clearances and floor protection, before actually beginning the installation.

If you are not using an existing chimney, place the appliance in a location to maintain a clear passage for the installation of any listed and approved pellet venting system. This appli- ance may be vented vertically or horizontally.

Maintain specified vent clearance to comubstible require- ments listed by the pellet manufactures venting instructions and all clearance to combustivles listed in this manual.

Check with your local building code agency before you begin your installation. Be sure local building codes do not super- sede UL specifications and always obtain a building permit so that insurance protection benefits cannot be unexpectedly cancelled. If any assistance is required during installation, please contact your local dealer.

We recommend that a qualified building inspector and your insurance company representative review your plans before and after installation.

2. Thermostat Location

The thermostat’s location will have some effect on the appliance’s operation. When the thermostat is located close to the appliance, it may require a slightly higher temperature setting to keep the rest of the house comfortable. If the thermostat location is in an adjacent room or on a different floor level, you will notice higher temperatures near the appliance.

CAUTION

•Do NOT connect this unit to a chimney flue servicing another appliance.

•Do NOT connect to any air distribution duct or system.

B. Fire Safety

Maintain the designated clearances to combustibles. Insu- lation must not touch the chimney. You must maintain the designated air space clearance around the chimney. This space around a chimney is necessary to allow natural heat removal from the area. Insulation in this space will cause a heat buildup, which may ignite wood framing. NOTE:

Clearances may only be reduced by means approved by the regulatory authority having jurisdiction.

To provide reasonable fire safety, the following should be given serious consideration:

1.Install at least one smoke detector on each floor of your home to ensure your safety. They should be located away from the heating appliance and close to the sleeping areas. Follow the smoke detector manufacturer’s placement and installation instructions, and be sure to maintain regularly.

2.A conveniently located Class A fire extinguisher to contend with small fires resulting from burning embers.

3.A practiced evacuation plan, consisting of at least 2 escape routes.

4.A plan to deal with a hopper fire as follows: In the event of a hopper fire:

a.Evacuate the house immediately.

b.Notify fire department.

WARNING

Fire Risk.

•Do not operate appliance before reading and understanding operating instructions.

•Failure to operate appliance properly may cause a house fire.

September 1, 2008

250-7251F

Page 5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents 810-02901 MBK 810-03201 PMH Castile Pellet InsertLocation Inside hopper on the top Castile Pellet InsertTable of Contents Appliance Certification BTU & Efficiency Specifications Listing and Code ApprovalsMobile Home Approved Glass SpecificationsFire Safety Design, Installation & Location ConsiderationsGetting Started Appliance LocationInspect Appliance & Components and Pre-Use Check List Castile Pellet Insert Tools And Supplies NeededAppliance Dimensions 3Dimensions and Clearances0mm Clearance To Exposed Section And Face Trim Castile Pellet Insert Clearance To Combustibles, UL and ULCShown Optional Outside Air Inches MillimetersFloor Protection Castile Pellet Insert Masonry and Zero Clearance FireplacesMinimum Opening for Masonry and Zero Clearance Fireplaces Location Inches MillimetersStarter hole Mark area of floor to cut Venting Termination Requirements 4Vent InformationChimney and Exhaust Connection Example of 3 Elbow-Rear Vent Termination Calculation Pipe Selection ChartCastile Pellet Insert Equivalent Feet of Pipe 5Venting Systems Castile Pellet Insert Full Reline With Outside Air 6Mobile Home Mobile Home InstallationRear Vent Installation Top Vent Installation7Appliance Set-Up Reversible Top or Rear Flue Adapter Leveling SystemItemDescription Assembled ViewCastile Pellet Insert Zero Clearance Trim Support Cont’d Base Plate Only InstallationKit Includes See Piece. FigurePanel & Trim Set, Econo Panel Set And Cast Trim SetTop Log Installation Four Piece Log Set InstallationCastile Pellet Insert Thermostat Installation General Operating Information Operating InstructionsFuel Size And Material Fire Characteristics Feed Rate AdjustmentCastile Pellet Insert Before Your First Fire Starting Your First FireCastile Pellet Insert Iginition Cycles Frequently Asked QuestionsPossible Cause Corrective Action TroubleshootingSymptom Page Symptom Possible Cause Corrective Action Cleaning or Inspection Quick Reference Maintenance Chart10Maintaining & Servicing Your Appliance Frequency Daily Weekly Monthly YearlyCleaning Firepot with Cleaning Rod & Firepot Scraper Remove Cast Sides for Cleaning & MaintenanceAsh Removal from Firebox See Disposal of AshesCleaning the Exhaust Path Cleaning Heat Exchanger Chambers & Drop TubeCleaning Beneath Heat Exchanger Cleaning Convection Blower Requires No Lubrication Cleaning the HopperCleaning the Glass Cleaning Exhaust Blower Requires No LubricationPreparing Firebox for Non-Burn Season Frequency Yearly High Ash Fuel Content MaintenanceDoor Gasket Inspection Igniter Replacement 35.1 Baffle & Brick Set RemovalRe-installing Baffle & Brick Set Cont’d Component Function Wiring Harness See .1 below Vacuum SwitchSnap Disc #1 Convection Blower 110F Snap Disc #2 Fuel Delivery Interrupt 250FCastile Pellet Insert Component Locations Cleaning Rods & Heat Exchanger TubesGlass Size 11-5/8 wide x 17-1/4 high Castile Pellet Insert Exploded ViewsDescription Item # Part Description, Alphabetical Order Part Number Castile Pellet Insert Service Parts and AccessoriesItem # Part Description, Alphabetical Order Item No Accessories, Alphabetical OrderItem No Appliance Date of Service Performed By Description of Service Castile Pellet Insert Service And Maintenance LogCastile Pellet Insert Service And Maintenance Log Cont’d Castile Pellet Insert Homeowner’s Notes CONDITIONS, Exclusions & Limitation of Liability Castile Pellet Insert Warranty PolicyHearth & Home Technologies Limited Warranty Cont’d Telephone Castile Pellet Insert

CASTINS-CWL, CASTINS-CSB, 810-03201 (PMH), 810-02901 (MBK) specifications

Hearth and Home Technologies has made a significant mark in the hearth and home industry with a variety of innovative products, including models like the 810-02901 (MBK), 810-03201 (PMH), CASTINS-CSB, and CASTINS-CWL. These models reflect state-of-the-art design and engineering, ensuring comfort and efficiency in residential heating solutions.

The 810-02901 (MBK) model is designed primarily for modular design, allowing for easy installation and integration into various home architectures. This model features advanced combustion technology that maximizes fuel efficiency while minimizing emissions. It is equipped with an innovative air control system that provides users with precise control over flame height and heat output, enhancing the overall user experience. With features such as a large viewing area, the MBK model provides an attractive look while ensuring optimum safety.

The 810-03201 (PMH) model offers versatile heating options and an elegant design that fits seamlessly into modern interiors. This model is notable for its user-friendly interface, which enables users to control settings with ease. It also has a remarkable heat distribution system, allowing warmth to spread evenly throughout the space, reducing cold spots and enhancing comfort. Additionally, the PMH model is built with durable materials that withstand the test of time, making it a long-lasting investment for homeowners.

The CASTINS-CSB and CASTINS-CWL models represent the pinnacle of contemporary fireplace design with their cast iron construction, enhancing durability and offering superior heat retention. Both models feature intricate designs that not only elevate the aesthetic of any room but also provide effective heating solutions. With the CASTINS series, Hearth and Home Technologies emphasizes the importance of safety with features such as heat shields and advanced flue systems that ensure proper ventilation.

In summary, Hearth and Home Technologies' 810-02901 (MBK), 810-03201 (PMH), CASTINS-CSB, and CASTINS-CWL models are characterized by their innovative technology, elegant design, and efficient heating capabilities. These models cater to a variety of homeowner needs, providing comfort, efficiency, and safety while enhancing interior aesthetics. Whether you’re looking for a robust heating solution or an elegant focal point in your home, Hearth and Home Technologies offers durable and stylish options that stand out in any environment.
Top Page Image Contents