Hearth and Home Technologies 810-02901 (MBK) Castile Pellet Insert Tools And Supplies Needed

Page 6

R

Castile Pellet Insert

C. Tools And Supplies Needed

Tools and building supplies normally required for installation, unless installing into an existing masonry fireplace:

Reciprocating Saw

Safety Glasses

Hammer

Framing Square

Phillips Screwdriver

Electric Drill & Bits (1/4”)

Tape Measure

1/4” Self-Tapping Screws

Plumb Line

May also need:

Level

Framing Material

Vent Support Straps

Hi-temp Caulking Material

Venting Paint

Gloves

 

WARNING

Inspect appliance and components for damage. Damaged parts may impair safe operation.

•Do NOT install damaged components.

•Do NOT install incomplete components.

•Do NOT install substitute components.

Report damaged parts to dealer.

WARNING

Fire Risk.

Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following actions:

•Installation and use of any damaged appliance.

•Modification of the appliance.

•Installation other than as instructed by Hearth & Home Technologies.

•Installation and/or use of any component part not approved by Hearth & Home Technologies.

•Operating appliance without fully assembling all components.

•Do NOT Overfire.

Or any such action that may cause a fire hazard.

D. Inspect Appliance & Components and Pre-Use Check List

1.

 

Place the appliance in a location near the

 

 

final installation area and follow the proce-

 

 

dures below:

2.

 

Open the appliance and remove all the parts

 

 

and articles packed inside the Component

 

 

Pack. Inspect all the parts and glass for ship-

 

 

ping damage. Contact your dealer if any irregu-

 

 

larities are noticed.

3.

 

All safety warnings have been read and fol-

 

 

lowed.

4.

 

This Owner’s Manual has been read.

5.

 

Floor protection requirements have been met.

6.

 

Venting is properly installed.

7.

 

The proper clearances from the appliance and

 

 

chimney to combustible materials have been

 

 

met.

8.

 

The masonry chimney is inspected by a profes-

 

 

sional and is clean, or the factory built metal

 

 

chimney is installed according to the manufac-

 

 

turer’s instructions and clearances.

9.

 

The chimney meets the required minimum

 

 

height.

10.

 

All labels have been removed from the glass

 

 

door.

11.

 

Plated surfaces have been wiped clean, if

 

 

applicable.

12.

 

Thermostat or remote has been installed.

13.

 

A power outlet is available nearby.

Page 6

250-7251F

September 1, 2008

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Castile Pellet Insert 810-02901 MBK 810-03201 PMHCastile Pellet Insert Location Inside hopper on the topTable of Contents Mobile Home Approved Listing and Code ApprovalsAppliance Certification BTU & Efficiency Specifications Glass SpecificationsGetting Started Design, Installation & Location ConsiderationsFire Safety Appliance LocationCastile Pellet Insert Tools And Supplies Needed Inspect Appliance & Components and Pre-Use Check List3Dimensions and Clearances Appliance DimensionsShown Optional Outside Air Castile Pellet Insert Clearance To Combustibles, UL and ULC0mm Clearance To Exposed Section And Face Trim Inches MillimetersMinimum Opening for Masonry and Zero Clearance Fireplaces Castile Pellet Insert Masonry and Zero Clearance FireplacesFloor Protection Location Inches MillimetersStarter hole Mark area of floor to cut 4Vent Information Chimney and Exhaust ConnectionVenting Termination Requirements Pipe Selection Chart Castile Pellet Insert Equivalent Feet of PipeExample of 3 Elbow-Rear Vent Termination Calculation 5Venting Systems Castile Pellet Insert Full Reline With Outside Air Mobile Home Installation 6Mobile Home7Appliance Set-Up Top Vent InstallationRear Vent Installation Reversible Top or Rear Flue Adapter Leveling SystemAssembled View ItemDescriptionKit Includes See Base Plate Only InstallationCastile Pellet Insert Zero Clearance Trim Support Cont’d Piece. FigurePanel Set And Cast Trim Set Panel & Trim Set, EconoFour Piece Log Set Installation Top Log InstallationCastile Pellet Insert Thermostat Installation Operating Instructions Fuel Size And MaterialGeneral Operating Information Castile Pellet Insert Before Your First Fire Feed Rate AdjustmentFire Characteristics Starting Your First FireFrequently Asked Questions Castile Pellet Insert Iginition CyclesTroubleshooting SymptomPossible Cause Corrective Action Page Symptom Possible Cause Corrective Action 10Maintaining & Servicing Your Appliance Quick Reference Maintenance ChartCleaning or Inspection Frequency Daily Weekly Monthly YearlyAsh Removal from Firebox Remove Cast Sides for Cleaning & MaintenanceCleaning Firepot with Cleaning Rod & Firepot Scraper See Disposal of AshesCleaning Heat Exchanger Chambers & Drop Tube Cleaning Beneath Heat ExchangerCleaning the Exhaust Path Cleaning the Glass Cleaning the HopperCleaning Convection Blower Requires No Lubrication Cleaning Exhaust Blower Requires No LubricationHigh Ash Fuel Content Maintenance Door Gasket InspectionPreparing Firebox for Non-Burn Season Frequency Yearly Igniter Replacement Baffle & Brick Set Removal 35.1Re-installing Baffle & Brick Set Cont’d Component Function Snap Disc #1 Convection Blower 110F Vacuum SwitchWiring Harness See .1 below Snap Disc #2 Fuel Delivery Interrupt 250FCleaning Rods & Heat Exchanger Tubes Castile Pellet Insert Component LocationsCastile Pellet Insert Exploded Views Glass Size 11-5/8 wide x 17-1/4 highDescription Castile Pellet Insert Service Parts and Accessories Item # Part Description, Alphabetical Order Part NumberItem No Accessories, Alphabetical Order Item No ApplianceItem # Part Description, Alphabetical Order Castile Pellet Insert Service And Maintenance Log Date of Service Performed By Description of ServiceCastile Pellet Insert Service And Maintenance Log Cont’d Castile Pellet Insert Homeowner’s Notes Castile Pellet Insert Warranty Policy CONDITIONS, Exclusions & Limitation of LiabilityHearth & Home Technologies Limited Warranty Cont’d Castile Pellet Insert Telephone

CASTINS-CWL, CASTINS-CSB, 810-03201 (PMH), 810-02901 (MBK) specifications

Hearth and Home Technologies has made a significant mark in the hearth and home industry with a variety of innovative products, including models like the 810-02901 (MBK), 810-03201 (PMH), CASTINS-CSB, and CASTINS-CWL. These models reflect state-of-the-art design and engineering, ensuring comfort and efficiency in residential heating solutions.

The 810-02901 (MBK) model is designed primarily for modular design, allowing for easy installation and integration into various home architectures. This model features advanced combustion technology that maximizes fuel efficiency while minimizing emissions. It is equipped with an innovative air control system that provides users with precise control over flame height and heat output, enhancing the overall user experience. With features such as a large viewing area, the MBK model provides an attractive look while ensuring optimum safety.

The 810-03201 (PMH) model offers versatile heating options and an elegant design that fits seamlessly into modern interiors. This model is notable for its user-friendly interface, which enables users to control settings with ease. It also has a remarkable heat distribution system, allowing warmth to spread evenly throughout the space, reducing cold spots and enhancing comfort. Additionally, the PMH model is built with durable materials that withstand the test of time, making it a long-lasting investment for homeowners.

The CASTINS-CSB and CASTINS-CWL models represent the pinnacle of contemporary fireplace design with their cast iron construction, enhancing durability and offering superior heat retention. Both models feature intricate designs that not only elevate the aesthetic of any room but also provide effective heating solutions. With the CASTINS series, Hearth and Home Technologies emphasizes the importance of safety with features such as heat shields and advanced flue systems that ensure proper ventilation.

In summary, Hearth and Home Technologies' 810-02901 (MBK), 810-03201 (PMH), CASTINS-CSB, and CASTINS-CWL models are characterized by their innovative technology, elegant design, and efficient heating capabilities. These models cater to a variety of homeowner needs, providing comfort, efficiency, and safety while enhancing interior aesthetics. Whether you’re looking for a robust heating solution or an elegant focal point in your home, Hearth and Home Technologies offers durable and stylish options that stand out in any environment.
Top Page Image Contents