Hearth and Home Technologies 810-02901 (MBK) Castile Pellet Insert Full Reline With Outside Air

Page 14

R

Castile Pellet Insert

C. Full Reline With Outside Air

12” (305mm) min. above

12” (305mm) min. below

NOTE: Check clearances carefully for this type of installation to ensure adequate room for outside air venting.

CAUTION

Check building codes prior to installation.

•Installation MUST comply with local, regional, state and national codes and regulations.

•Consult local building, fire officials or authori- ties having jurisdiction about restrictions, installation inspection, and permits.

NOTE: In Canada, only a full reline is allowed per ULC S-628, ORD ULC C1482.

NOTE; Use metal plate around exhaust vent pipe and seal all edges with non-flammable insulation such as fiberglass, mineral wool or ceramic.

Do not use high temperature caulk- ing materials to seal any edge to prevent furture serviceability.

Outside Air

Termination

at Chimney Top

Exit through the Ash Clean-Out of Masonry Chimney

Outside Air

through

Rear Wall

Figure 14.2

Page 14

250-7251F

September 1, 2008

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Castile Pellet Insert 810-02901 MBK 810-03201 PMHCastile Pellet Insert Location Inside hopper on the topTable of Contents Mobile Home Approved Listing and Code ApprovalsAppliance Certification BTU & Efficiency Specifications Glass SpecificationsGetting Started Design, Installation & Location ConsiderationsFire Safety Appliance LocationCastile Pellet Insert Tools And Supplies Needed Inspect Appliance & Components and Pre-Use Check List3Dimensions and Clearances Appliance DimensionsShown Optional Outside Air Castile Pellet Insert Clearance To Combustibles, UL and ULC0mm Clearance To Exposed Section And Face Trim Inches MillimetersMinimum Opening for Masonry and Zero Clearance Fireplaces Castile Pellet Insert Masonry and Zero Clearance FireplacesFloor Protection Location Inches MillimetersStarter hole Mark area of floor to cut Venting Termination Requirements 4Vent InformationChimney and Exhaust Connection Example of 3 Elbow-Rear Vent Termination Calculation Pipe Selection ChartCastile Pellet Insert Equivalent Feet of Pipe 5Venting Systems Castile Pellet Insert Full Reline With Outside Air Mobile Home Installation 6Mobile Home7Appliance Set-Up Top Vent InstallationRear Vent Installation Reversible Top or Rear Flue Adapter Leveling SystemAssembled View ItemDescriptionKit Includes See Base Plate Only InstallationCastile Pellet Insert Zero Clearance Trim Support Cont’d Piece. FigurePanel Set And Cast Trim Set Panel & Trim Set, EconoFour Piece Log Set Installation Top Log InstallationCastile Pellet Insert Thermostat Installation General Operating Information Operating InstructionsFuel Size And Material Castile Pellet Insert Before Your First Fire Feed Rate AdjustmentFire Characteristics Starting Your First FireFrequently Asked Questions Castile Pellet Insert Iginition CyclesPossible Cause Corrective Action TroubleshootingSymptom Page Symptom Possible Cause Corrective Action 10Maintaining & Servicing Your Appliance Quick Reference Maintenance ChartCleaning or Inspection Frequency Daily Weekly Monthly YearlyAsh Removal from Firebox Remove Cast Sides for Cleaning & MaintenanceCleaning Firepot with Cleaning Rod & Firepot Scraper See Disposal of AshesCleaning the Exhaust Path Cleaning Heat Exchanger Chambers & Drop TubeCleaning Beneath Heat Exchanger Cleaning the Glass Cleaning the HopperCleaning Convection Blower Requires No Lubrication Cleaning Exhaust Blower Requires No LubricationPreparing Firebox for Non-Burn Season Frequency Yearly High Ash Fuel Content MaintenanceDoor Gasket Inspection Igniter Replacement Baffle & Brick Set Removal 35.1Re-installing Baffle & Brick Set Cont’d Component Function Snap Disc #1 Convection Blower 110F Vacuum SwitchWiring Harness See .1 below Snap Disc #2 Fuel Delivery Interrupt 250FCleaning Rods & Heat Exchanger Tubes Castile Pellet Insert Component LocationsCastile Pellet Insert Exploded Views Glass Size 11-5/8 wide x 17-1/4 highDescription Castile Pellet Insert Service Parts and Accessories Item # Part Description, Alphabetical Order Part NumberItem # Part Description, Alphabetical Order Item No Accessories, Alphabetical OrderItem No Appliance Castile Pellet Insert Service And Maintenance Log Date of Service Performed By Description of ServiceCastile Pellet Insert Service And Maintenance Log Cont’d Castile Pellet Insert Homeowner’s Notes Castile Pellet Insert Warranty Policy CONDITIONS, Exclusions & Limitation of LiabilityHearth & Home Technologies Limited Warranty Cont’d Castile Pellet Insert Telephone

CASTINS-CWL, CASTINS-CSB, 810-03201 (PMH), 810-02901 (MBK) specifications

Hearth and Home Technologies has made a significant mark in the hearth and home industry with a variety of innovative products, including models like the 810-02901 (MBK), 810-03201 (PMH), CASTINS-CSB, and CASTINS-CWL. These models reflect state-of-the-art design and engineering, ensuring comfort and efficiency in residential heating solutions.

The 810-02901 (MBK) model is designed primarily for modular design, allowing for easy installation and integration into various home architectures. This model features advanced combustion technology that maximizes fuel efficiency while minimizing emissions. It is equipped with an innovative air control system that provides users with precise control over flame height and heat output, enhancing the overall user experience. With features such as a large viewing area, the MBK model provides an attractive look while ensuring optimum safety.

The 810-03201 (PMH) model offers versatile heating options and an elegant design that fits seamlessly into modern interiors. This model is notable for its user-friendly interface, which enables users to control settings with ease. It also has a remarkable heat distribution system, allowing warmth to spread evenly throughout the space, reducing cold spots and enhancing comfort. Additionally, the PMH model is built with durable materials that withstand the test of time, making it a long-lasting investment for homeowners.

The CASTINS-CSB and CASTINS-CWL models represent the pinnacle of contemporary fireplace design with their cast iron construction, enhancing durability and offering superior heat retention. Both models feature intricate designs that not only elevate the aesthetic of any room but also provide effective heating solutions. With the CASTINS series, Hearth and Home Technologies emphasizes the importance of safety with features such as heat shields and advanced flue systems that ensure proper ventilation.

In summary, Hearth and Home Technologies' 810-02901 (MBK), 810-03201 (PMH), CASTINS-CSB, and CASTINS-CWL models are characterized by their innovative technology, elegant design, and efficient heating capabilities. These models cater to a variety of homeowner needs, providing comfort, efficiency, and safety while enhancing interior aesthetics. Whether you’re looking for a robust heating solution or an elegant focal point in your home, Hearth and Home Technologies offers durable and stylish options that stand out in any environment.
Top Page Image Contents