Hearth and Home Technologies 810-03201 (PMH) 4Vent Information, Chimney and Exhaust Connection

Page 11

R

Castile Pellet Insert

4Vent Information

A. Chimney and Exhaust Connection

1.Chimney & Connector: Use 3 or 4 inch (76-102mm) diameter type "L" or "PL" venting system. It can be vented vertically or horizontally.

2.Mobile Home: Approved for all Listed pellet vent. Use Listed double wall flue connector. A Quadra-Fire outside air kit must be used with manufactured home installa- tions.

3.Residential: Use 24 gauge single wall flue connector or a Listed double wall flue connector to Class A Listed metal chimneys, or masonry chimneys meeting national and/or local codes for solid fuel appliances.

4.INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER.

5.Secure exhaust venting system to the appliance with at least 3 screws. Also secure all connector pipe joints with at least 3 screws through each joint.

NOTE: All pipe must be welded seam pipe whenever pos- sible. Seal pipe joints with high temperature silicone (500°F [260°C] minimum rated only).

NOTE: If burning shelled field corn, you must use approved venting specifically designed for corn. Follow the instruc- tions from the venting manufacturer.

WARNING

Fire Risk.

•Only LISTED venting components may be used.

•NO OTHER vent components may be used. Substitute or damaged vent components may impair safe operation.

B. Venting Termination Requirements

CAUTION

Do not terminate vent in any enclosed or semi-enclosed area such as a carport, garage, attic, crawl space, under a sun deck or porch, narrow walkway or closely fenced area, or any location that can build up a concentration of fumes such as a stairwell, covered breezeway, etc.

1. Termination must exhaust above air inlet elevation. It is recommended that at least 60 inches (1524mm) of verti- cal pipe be installed when appliance is vented directly through a wall. This will create a natural draft, which will help prevent the possibility of smoke or odor venting into the home during a power outage. It will also keep exhaust from causing a nuisance or hazard by exposing people or shrubs to high temperatures. The safest and preferred venting method is to extend the vent vertically through the roof.

2. Distance from doors and opening windows, or gravity or ventilation air inlets into building:

a.Not less than 48 inches (1219mm) below;

b.Not less than 48 inches (1219mm) horizontally from;

c.Not less than 12 inches (305mm) above.

3.Distance from permanently closed windows:

a.Not less than 12 inches (305mm) below, horizontally from or above.

4. Distance between bottom of termination and grade should be 12 inches (305mm) minimum. This is con- ditional upon plants in the area, and nature of grade surface. The grade surface must be a non-combustible material (i.e., rock, dirt). The grade surface must not be lawn. Distance between bottom of termination and public walkway should be 84 inches (2134mm) minimum.

WARNING

Vent surfaces get HOT, can cause burns if touched. Non-combustible shielding or guards may be required.

5. Distance to combustible materials must be 24 inches (610mm) minimum. This includes adjacent buildings, fences, protruding parts of the structure, roof overhang, plants and shrubs, etc.

6.Termination Cap Location (Home Electrical Service)

•Side-to-side clearance is to be the same as minimum clearance to vinyl inside corners.

•Clearance of a termination cap below electrical service shall be the same as minimum clearance to vinyl soffits.

•Clearance of a termination cap above electrical service will be 12 inches (305mm) minimum.

•Location of the vent termination must not obstruct or interfere with access to the electrical service.

September 1, 2008

250-7251F

Page 11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents 810-02901 MBK 810-03201 PMH Castile Pellet InsertLocation Inside hopper on the top Castile Pellet InsertTable of Contents Glass Specifications Listing and Code ApprovalsAppliance Certification BTU & Efficiency Specifications Mobile Home ApprovedAppliance Location Design, Installation & Location ConsiderationsFire Safety Getting StartedInspect Appliance & Components and Pre-Use Check List Castile Pellet Insert Tools And Supplies NeededAppliance Dimensions 3Dimensions and ClearancesInches Millimeters Castile Pellet Insert Clearance To Combustibles, UL and ULC0mm Clearance To Exposed Section And Face Trim Shown Optional Outside AirLocation Inches Millimeters Castile Pellet Insert Masonry and Zero Clearance FireplacesFloor Protection Minimum Opening for Masonry and Zero Clearance FireplacesStarter hole Mark area of floor to cut Venting Termination Requirements 4Vent InformationChimney and Exhaust Connection Example of 3 Elbow-Rear Vent Termination Calculation Pipe Selection ChartCastile Pellet Insert Equivalent Feet of Pipe 5Venting Systems Castile Pellet Insert Full Reline With Outside Air 6Mobile Home Mobile Home InstallationReversible Top or Rear Flue Adapter Leveling System Top Vent InstallationRear Vent Installation 7Appliance Set-UpItemDescription Assembled ViewPiece. Figure Base Plate Only InstallationCastile Pellet Insert Zero Clearance Trim Support Cont’d Kit Includes SeePanel & Trim Set, Econo Panel Set And Cast Trim SetTop Log Installation Four Piece Log Set InstallationCastile Pellet Insert Thermostat Installation General Operating Information Operating InstructionsFuel Size And Material Starting Your First Fire Feed Rate AdjustmentFire Characteristics Castile Pellet Insert Before Your First FireCastile Pellet Insert Iginition Cycles Frequently Asked QuestionsPossible Cause Corrective Action TroubleshootingSymptom Page Symptom Possible Cause Corrective Action Frequency Daily Weekly Monthly Yearly Quick Reference Maintenance ChartCleaning or Inspection 10Maintaining & Servicing Your ApplianceSee Disposal of Ashes Remove Cast Sides for Cleaning & MaintenanceCleaning Firepot with Cleaning Rod & Firepot Scraper Ash Removal from FireboxCleaning the Exhaust Path Cleaning Heat Exchanger Chambers & Drop TubeCleaning Beneath Heat Exchanger Cleaning Exhaust Blower Requires No Lubrication Cleaning the HopperCleaning Convection Blower Requires No Lubrication Cleaning the GlassPreparing Firebox for Non-Burn Season Frequency Yearly High Ash Fuel Content MaintenanceDoor Gasket Inspection Igniter Replacement 35.1 Baffle & Brick Set RemovalRe-installing Baffle & Brick Set Cont’d Component Function Snap Disc #2 Fuel Delivery Interrupt 250F Vacuum SwitchWiring Harness See .1 below Snap Disc #1 Convection Blower 110FCastile Pellet Insert Component Locations Cleaning Rods & Heat Exchanger TubesGlass Size 11-5/8 wide x 17-1/4 high Castile Pellet Insert Exploded ViewsDescription Item # Part Description, Alphabetical Order Part Number Castile Pellet Insert Service Parts and AccessoriesItem # Part Description, Alphabetical Order Item No Accessories, Alphabetical OrderItem No Appliance Date of Service Performed By Description of Service Castile Pellet Insert Service And Maintenance LogCastile Pellet Insert Service And Maintenance Log Cont’d Castile Pellet Insert Homeowner’s Notes CONDITIONS, Exclusions & Limitation of Liability Castile Pellet Insert Warranty PolicyHearth & Home Technologies Limited Warranty Cont’d Telephone Castile Pellet Insert

CASTINS-CWL, CASTINS-CSB, 810-03201 (PMH), 810-02901 (MBK) specifications

Hearth and Home Technologies has made a significant mark in the hearth and home industry with a variety of innovative products, including models like the 810-02901 (MBK), 810-03201 (PMH), CASTINS-CSB, and CASTINS-CWL. These models reflect state-of-the-art design and engineering, ensuring comfort and efficiency in residential heating solutions.

The 810-02901 (MBK) model is designed primarily for modular design, allowing for easy installation and integration into various home architectures. This model features advanced combustion technology that maximizes fuel efficiency while minimizing emissions. It is equipped with an innovative air control system that provides users with precise control over flame height and heat output, enhancing the overall user experience. With features such as a large viewing area, the MBK model provides an attractive look while ensuring optimum safety.

The 810-03201 (PMH) model offers versatile heating options and an elegant design that fits seamlessly into modern interiors. This model is notable for its user-friendly interface, which enables users to control settings with ease. It also has a remarkable heat distribution system, allowing warmth to spread evenly throughout the space, reducing cold spots and enhancing comfort. Additionally, the PMH model is built with durable materials that withstand the test of time, making it a long-lasting investment for homeowners.

The CASTINS-CSB and CASTINS-CWL models represent the pinnacle of contemporary fireplace design with their cast iron construction, enhancing durability and offering superior heat retention. Both models feature intricate designs that not only elevate the aesthetic of any room but also provide effective heating solutions. With the CASTINS series, Hearth and Home Technologies emphasizes the importance of safety with features such as heat shields and advanced flue systems that ensure proper ventilation.

In summary, Hearth and Home Technologies' 810-02901 (MBK), 810-03201 (PMH), CASTINS-CSB, and CASTINS-CWL models are characterized by their innovative technology, elegant design, and efficient heating capabilities. These models cater to a variety of homeowner needs, providing comfort, efficiency, and safety while enhancing interior aesthetics. Whether you’re looking for a robust heating solution or an elegant focal point in your home, Hearth and Home Technologies offers durable and stylish options that stand out in any environment.
Top Page Image Contents