Haier 3150 SF important safety instructions Model SA3AAA Shown, High Sanitation Pumps, 310622L

Page 1

Instructions/Parts List

High Sanitation Pumps

For use in sanitary applications.

310622L

Models 1590 & 3150 SA__ Sanitary Diaphragm Pump 44-03Models 1590 & 3150 SB__ Sanitary Ball Check Pump II 2 G c T6Model 3150 SF__ Sanitary Flapper Check Pump II 2 G c T6

120 psi (0.8 MPa, 8 bar) Maximum Fluid Working Pressure 120 psi (0.8 MPa, 8 bar) Maximum Air Input Pressure

Important Safety Instructions. Read all warnings and instructions in this manual. Save these instructions.

See page 2 for Table of Contents.

Model SA3AAA Shown	TI8760a

US and Foreign Patents Pending

US Patent No. 5,368,452

Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441

Image 1

Contents Instructions/Parts List Model SA3AAA ShownHigh Sanitation Pumps 310622LContents ContentsDimensional Drawing Technical DataWarnings WarningsFIRE AND EXPLOSION HAZARD PRESSURIZED EQUIPMENT HAZARDPERSONAL PROTECTIVE EQUIPMENT BURN HAZARDInstallation InstallationGeneral Information Leak Detection SystemMountings Ground Wire ConnectionAir Line Fluid Suction LineFIG. 3 Typical Floor-Mount Installation Typical InstallationFluid Outlet Line Air Exhaust Ventilation Changing the Orientation of the Fluid Inlet and Outlet PortsFIG. 4 Orientation of Fluid Ports E Master air valve for accessories F Air line filter P Muffler FIG. 5 Venting Exhaust AirA Air supply line B Bleed-type master air valve required for pump C Air regulator D Air line quick disconnectStarting and Adjusting the Pump Pressure Relief ProcedureOperation Sanitizing the Pump Before First UseRoutine Cleaning of Product Contact Section of Pump MaintenanceMaintenance LubricationMaintenance Person Preventive Maintenance ScheduleOperator Task310622L Troubleshooting TroubleshootingPROBLEM Follow Pressure Relief ProceLeak in inlet or outlet sanitary fit erly/cleanly due to imbalanceLoose sanitary clamp Tighten clampRepairing the Air Valve ServiceService DisassemblyReassembly 8. Install the valve carriage 105 so its tabs slip into the grooves on the narrow end of the actuator pis- tons 111. See FIG Check Valve Repair 3A Ball Check AssemblySanitary Ball Check Assembly Service For Sanitary Ball Check pumps remove ball gasketFlapper Check Assembly TI8769aTools Required Diaphragm Repair3A Pump Sanitary Pumpdiaphragm plate side high strength thread lock shaft sideBearing and Air Gasket Removal Reassembly 3150 Stainless Steel Sanitary Pumps Pump Matrix1590 Stainless Steel Sanitary Pumps Pump MatrixFlapper Check Valve Assembly Sanitary Ball Check Valve AssemblySanitary Diaphragm Assembly Parts DrawingPump Configuration Parts List Parts ListInlet and Outlet Parts List Parts ListIndicates replacement parts † Indicates a recommended spare part Diaphragm Material Parts ListPart 3150Indicates replacement parts † Indicates a recommended spare part Check Ball Material Parts ListApply medium strength adhesive to outside center housing boreApply a medium strength thread locker to screw threads and torque to 130-150 in-lbsAir Section Parts Leak Detector and Pump Stand Parts ListFluid Section Parts Accessories Accessories3150 Conversion Kits 15D990 Leak DetectorModel Dimensional DrawingModel TI8778aSantoprene is a registered trademark of the Monsanto Co Technical DataLoctite is a registered trademark of the Loctite Corporation 1590 3A Performance Chart Performance ChartTest Conditions Pump tested in water with inlet submerged To find Fluid Outlet PressureSanitary Ball Check Valve Pumps 3A Ball Check Valve PumpsFlapper Check Valve Pumps Model 3150 3A Performance Chart 310622L Extended Product Warranty Graco Standard Pump WarrantyGraco Warranties Graco Information