Haier 3150 SF, 3150 SB 3A Ball Check Valve Pumps, Sanitary Ball Check Valve Pumps, Model, 310622L

Page 36

Model 3150

Dimensional Drawing

3A Ball Check Valve Pumps

22.0in

(558.8 mm)

28.4in.

(721.4 mm)

6.5 in.

(165.1 mm)

		23.5 in.
TI4929d		(596.9 mm)

37.6in.

(955.0 mm)

TI7610c

Sanitary Ball Check Valve Pumps		Flapper Check Valve Pumps

28.3 in.		37.5 in.	29.5 in.		38.1 in.
(718.8 mm)		37.5 in.	(749.3 mm)		(967.7 mm)
		(952.5 mm)
6.5 in.			5.9 in.
(165.1 mm)			(149.9 mm)
	19.3 in.			19.3 in.	TI4928d
	19.3 in.			(490.2 mm)
	(490.2 mm)	TI4685d
		TI4685d

36					310622L

Image 36

Contents Model SA3AAA Shown Instructions/Parts ListHigh Sanitation Pumps 310622LContents ContentsDimensional Drawing Technical DataWarnings WarningsFIRE AND EXPLOSION HAZARD PRESSURIZED EQUIPMENT HAZARDBURN HAZARD PERSONAL PROTECTIVE EQUIPMENTInstallation InstallationGeneral Information Leak Detection SystemGround Wire Connection MountingsAir Line Fluid Suction LineTypical Installation FIG. 3 Typical Floor-Mount InstallationFluid Outlet Line Changing the Orientation of the Fluid Inlet and Outlet Ports Air Exhaust VentilationFIG. 4 Orientation of Fluid Ports FIG. 5 Venting Exhaust Air E Master air valve for accessories F Air line filter P MufflerA Air supply line B Bleed-type master air valve required for pump C Air regulator D Air line quick disconnectPressure Relief Procedure Starting and Adjusting the PumpOperation Sanitizing the Pump Before First UseMaintenance Routine Cleaning of Product Contact Section of PumpMaintenance LubricationPreventive Maintenance Schedule Maintenance PersonOperator TaskMaintenance Troubleshooting TroubleshootingPROBLEM Follow Pressure Relief Proceerly/cleanly due to imbalance Leak in inlet or outlet sanitary fitLoose sanitary clamp Tighten clampService Repairing the Air ValveService DisassemblyReassembly 8. Install the valve carriage 105 so its tabs slip into the grooves on the narrow end of the actuator pis- tons 111. See FIG 3A Ball Check Assembly Check Valve RepairService For Sanitary Ball Check pumps remove ball gasket Sanitary Ball Check AssemblyFlapper Check Assembly TI8769aDiaphragm Repair Tools RequiredSanitary Pump 3A Pumpdiaphragm plate side high strength thread lock shaft sideBearing and Air Gasket Removal Service Pump Matrix 3150 Stainless Steel Sanitary Pumps1590 Stainless Steel Sanitary Pumps Pump MatrixSanitary Ball Check Valve Assembly Flapper Check Valve AssemblySanitary Diaphragm Assembly Parts DrawingParts List Pump Configuration Parts ListInlet and Outlet Parts List Parts ListDiaphragm Material Parts List Indicates replacement parts † Indicates a recommended spare partPart 3150Check Ball Material Parts List Indicates replacement parts † Indicates a recommended spare partcenter housing bore Apply medium strength adhesive to outsideApply a medium strength thread locker to screw threads and torque to 130-150 in-lbsLeak Detector and Pump Stand Parts List Air Section PartsFluid Section Parts Accessories Accessories3150 Conversion Kits 15D990 Leak DetectorDimensional Drawing ModelModel TI8778aTechnical Data Santoprene is a registered trademark of the Monsanto CoLoctite is a registered trademark of the Loctite Corporation Performance Chart 1590 3A Performance ChartTest Conditions Pump tested in water with inlet submerged To find Fluid Outlet Pressure3A Ball Check Valve Pumps Sanitary Ball Check Valve PumpsFlapper Check Valve Pumps Technical Data 3150 3A Performance Chart Model Graco Standard Pump Warranty Extended Product WarrantyGraco Warranties Graco Information