Haier 1590 SB, 3150 SB, 3150 SF, 3150 SA Burn Hazard, Personal Protective Equipment, 310622L

Page 4

Warning

BURN HAZARD

Equipment surfaces and fluids that are heated can become very hot during operation. To avoid severe burns, do not touch hot fluid or equipment. Wait until equipment/fluid has cooled completely.

PERSONAL PROTECTIVE EQUIPMENT

You must wear appropriate protective equipment when operating, servicing, or when in the operating area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic fumes, burns, and hearing loss. This equipment includes but is not limited to:

•Protective eyewear

•Clothing and respirator as recommended by the fluid and solvent manufacturer

•Gloves

•Hearing protection

310622L

Image 4

Contents Model SA3AAA Shown Instructions/Parts ListHigh Sanitation Pumps 310622LContents ContentsDimensional Drawing Technical DataWarnings WarningsFIRE AND EXPLOSION HAZARD PRESSURIZED EQUIPMENT HAZARDBURN HAZARD PERSONAL PROTECTIVE EQUIPMENTInstallation InstallationGeneral Information Leak Detection SystemGround Wire Connection MountingsAir Line Fluid Suction LineFIG. 3 Typical Floor-Mount Installation Typical InstallationFluid Outlet Line Air Exhaust Ventilation Changing the Orientation of the Fluid Inlet and Outlet PortsFIG. 4 Orientation of Fluid Ports FIG. 5 Venting Exhaust Air E Master air valve for accessories F Air line filter P MufflerA Air supply line B Bleed-type master air valve required for pump C Air regulator D Air line quick disconnectPressure Relief Procedure Starting and Adjusting the PumpOperation Sanitizing the Pump Before First UseMaintenance Routine Cleaning of Product Contact Section of PumpMaintenance LubricationPreventive Maintenance Schedule Maintenance PersonOperator TaskMaintenance Troubleshooting TroubleshootingPROBLEM Follow Pressure Relief Proceerly/cleanly due to imbalance Leak in inlet or outlet sanitary fitLoose sanitary clamp Tighten clampService Repairing the Air ValveService DisassemblyReassembly 8. Install the valve carriage 105 so its tabs slip into the grooves on the narrow end of the actuator pis- tons 111. See FIG 3A Ball Check Assembly Check Valve RepairService For Sanitary Ball Check pumps remove ball gasket Sanitary Ball Check AssemblyFlapper Check Assembly TI8769aDiaphragm Repair Tools RequiredSanitary Pump 3A Pumpdiaphragm plate side high strength thread lock shaft sideBearing and Air Gasket Removal Reassembly Pump Matrix 3150 Stainless Steel Sanitary Pumps1590 Stainless Steel Sanitary Pumps Pump MatrixSanitary Ball Check Valve Assembly Flapper Check Valve AssemblySanitary Diaphragm Assembly Parts DrawingParts List Pump Configuration Parts ListInlet and Outlet Parts List Parts ListDiaphragm Material Parts List Indicates replacement parts † Indicates a recommended spare partPart 3150Check Ball Material Parts List Indicates replacement parts † Indicates a recommended spare partcenter housing bore Apply medium strength adhesive to outsideApply a medium strength thread locker to screw threads and torque to 130-150 in-lbsAir Section Parts Leak Detector and Pump Stand Parts ListFluid Section Parts Accessories Accessories3150 Conversion Kits 15D990 Leak DetectorDimensional Drawing ModelModel TI8778aSantoprene is a registered trademark of the Monsanto Co Technical DataLoctite is a registered trademark of the Loctite Corporation Performance Chart 1590 3A Performance ChartTest Conditions Pump tested in water with inlet submerged To find Fluid Outlet PressureSanitary Ball Check Valve Pumps 3A Ball Check Valve PumpsFlapper Check Valve Pumps Technical Data 3150 3A Performance Chart Model Graco Standard Pump Warranty Extended Product WarrantyGraco Warranties Graco Information