Haier 3150 SA Model, Technical Data, Santoprene is a registered trademark of the Monsanto Co

Page 37
316 SST, 3A Approved EPDM
316 SST, Santoprene®, Buna-N (Nitrile), fluoroelastomer,
3A Approved EPDM, PTFE

Model 3150

Model 3150

Technical Data

Maximum fluid working pressure . . . . . . . . . . . . . . . . . . .

Air pressure operating range . . . . . . . . . . . . . . . . . . . . . .

Maximum air consumption . . . . . . . . . . . . . . . . . . . . . . . .

Air consumption at 70 psi air inlet pressure/60 gpm. . . . .

Maximum free-flow delivery . . . . . . . . . . . . . . . . . . . . . . .

Maximum pump speed . . . . . . . . . . . . . . . . . . . . . . . . . . .

* Gallons (Liters) per cycle . . . . . . . . . . . . . . . . . . . . . . . .

Maximum suction lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maximum size pumpable solids . . . . . . . . . . . . . . . . . . . .

120 psi (0.8 MPa, 8 bar)

20-120 psi (0.14-0.8 MPa, 1.4-8 bar) 175 scfm

50 scfm (see chart)

150 gpm ( 570 l/min)

145cpm

1.03(3.90)

Flapper 10 ft (3.5 m) wet, 5 ft (1.75 m) dry Ball 18 ft (5.5 m) wet, 9 ft (2.75 m) dry

Flapper 2.5 in. (63.5 mm)

Ball 1.0 in. (25.4 mm)

** Maximum Noise Level at 100 psi, full flow . . . . . . . . . . 90 dBa ** Sound Power Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 dBa ** Noise Level at 70 psi and 50 cpm . . . . . . . . . . . . . . . . . 85 dBa

Maximum fluid operating temperature is based on the

PTFE 220°F (104.4°C)

following maximum diaphragm, ball, and seat temperature Santoprene® 180°F (82.2°C)

ratings

Buna-N 180°F (82.2°C)

 

fluoroelastomer 250°F (121.1°C)

 

3A Approved EPDM 275°F (135°C)

Air inlet size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 in. npt(f)

Wetted parts

***All fluid contact materials are FDA-compliant and meet the United States Code of Federal Regulations (CFR) Title 21, Section 177.

Wetted materials on all models. . . . . . . . . . . . . . . . . . . . .

Wetted material depending on model . . . . . . . . . . . . . . . .

CAUTION:

Santoprene® may be used only with non-fatty, non-oily foods or alcohols up to 15%.

Non-wetted external parts. . . . . . . . . . . . . . . . . . . . . . . . .

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

300 series stainless steel, polyester (labels), LDPE foam (gasket)

145 lb (66 kg)

Santoprene® is a registered trademark of the Monsanto Co.

Loctite® is a registered trademark of the Loctite Corporation.

*Displacement per cycle may vary based on suction condition, discharge head, air pressure, and fluid type.

**Noise levels measured with the pump mounted on the stand. Sound power measured per ISO Standard 9614-1.

***The pump user must verify that the construction materials meet their specific application requirements.

310622L

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Instructions/Parts List Model SA3AAA ShownHigh Sanitation Pumps 310622LContents ContentsDimensional Drawing Technical DataWarnings WarningsFIRE AND EXPLOSION HAZARD PRESSURIZED EQUIPMENT HAZARDPERSONAL PROTECTIVE EQUIPMENT BURN HAZARDInstallation InstallationGeneral Information Leak Detection SystemMountings Ground Wire ConnectionAir Line Fluid Suction LineFIG. 3 Typical Floor-Mount Installation Typical InstallationFluid Outlet Line Air Exhaust Ventilation Changing the Orientation of the Fluid Inlet and Outlet PortsFIG. 4 Orientation of Fluid Ports E Master air valve for accessories F Air line filter P Muffler FIG. 5 Venting Exhaust AirA Air supply line B Bleed-type master air valve required for pump C Air regulator D Air line quick disconnectStarting and Adjusting the Pump Pressure Relief ProcedureOperation Sanitizing the Pump Before First UseRoutine Cleaning of Product Contact Section of Pump MaintenanceMaintenance LubricationMaintenance Person Preventive Maintenance ScheduleOperator Task310622L Troubleshooting TroubleshootingPROBLEM Follow Pressure Relief ProceLeak in inlet or outlet sanitary fit erly/cleanly due to imbalanceLoose sanitary clamp Tighten clampRepairing the Air Valve ServiceService DisassemblyReassembly 8. Install the valve carriage 105 so its tabs slip into the grooves on the narrow end of the actuator pis- tons 111. See FIG Check Valve Repair 3A Ball Check AssemblySanitary Ball Check Assembly Service For Sanitary Ball Check pumps remove ball gasketFlapper Check Assembly TI8769aTools Required Diaphragm Repair3A Pump Sanitary Pumpdiaphragm plate side high strength thread lock shaft sideBearing and Air Gasket Removal Reassembly 3150 Stainless Steel Sanitary Pumps Pump Matrix1590 Stainless Steel Sanitary Pumps Pump MatrixFlapper Check Valve Assembly Sanitary Ball Check Valve AssemblySanitary Diaphragm Assembly Parts DrawingPump Configuration Parts List Parts ListInlet and Outlet Parts List Parts ListIndicates replacement parts † Indicates a recommended spare part Diaphragm Material Parts ListPart 3150Indicates replacement parts † Indicates a recommended spare part Check Ball Material Parts ListApply medium strength adhesive to outside center housing boreApply a medium strength thread locker to screw threads and torque to 130-150 in-lbsAir Section Parts Leak Detector and Pump Stand Parts ListFluid Section Parts Accessories Accessories3150 Conversion Kits 15D990 Leak DetectorModel Dimensional DrawingModel TI8778aSantoprene is a registered trademark of the Monsanto Co Technical DataLoctite is a registered trademark of the Loctite Corporation 1590 3A Performance Chart Performance ChartTest Conditions Pump tested in water with inlet submerged To find Fluid Outlet PressureSanitary Ball Check Valve Pumps 3A Ball Check Valve PumpsFlapper Check Valve Pumps Model 3150 3A Performance Chart 310622L Extended Product Warranty Graco Standard Pump WarrantyGraco Warranties Graco Information
Top Page Image Contents