Haier 1590 SA Changing the Orientation of the Fluid Inlet and Outlet Ports, Installation, 310622L

Page 8

Changing the Orientation of the Fluid Inlet and Outlet Ports

Installation

Changing the Orientation of the Fluid Inlet and Outlet Ports

The pump is shipped with the ports facing the same direction. To re-orientate the ports into any position:

1.Remove the clamps (130) holding the inlet and/or outlet tee to the elbows.

2.Rotate the manifold tee (339) and reattach. Install the clamps (130) and tighten handtight.

130

339

P

TI5133e

FIG. 4 Orientation of Fluid Ports

Air Exhaust Ventilation

Be sure the system is properly ventilated for your type of installation. You must vent the exhaust to a safe place, away from people, animals, food handling areas, and all sources of ignition when pumping flam- mable or hazardous fluids.

Diaphragm failure can cause the fluid being pumped to exhaust with the air. Place an appropriate con- tainer at the end of the air exhaust line to catch the fluid. See FIG. 5.

The air exhaust port is 3/4 npt(f). Do not restrict the air exhaust port. Excessive exhaust restriction can cause erratic pump operation.

To provide a remote exhaust:

1.Remove the muffler (P) from the pump air exhaust port. See FIG. 5.

2.Install a grounded air exhaust hose (T) and connect the muffler (P) to the other end of the hose. The minimum size for the air exhaust hose is 3/4 in. (19 mm) ID. If a hose longer than 15 ft (4.57 m) is required, use a larger diameter hose. Avoid sharp bends or kinks in the hose.

3.Place a grounded container (U) at the end of the air exhaust line to catch fluid in case of a diaphragm rupture. See FIG. 5.

8

310622L

Image 8

Contents Model SA3AAA Shown Instructions/Parts ListHigh Sanitation Pumps 310622LContents ContentsDimensional Drawing Technical DataWarnings WarningsFIRE AND EXPLOSION HAZARD PRESSURIZED EQUIPMENT HAZARDBURN HAZARD PERSONAL PROTECTIVE EQUIPMENTInstallation InstallationGeneral Information Leak Detection SystemGround Wire Connection MountingsAir Line Fluid Suction LineFluid Outlet Line Typical InstallationFIG. 3 Typical Floor-Mount Installation FIG. 4 Orientation of Fluid Ports Changing the Orientation of the Fluid Inlet and Outlet PortsAir Exhaust Ventilation FIG. 5 Venting Exhaust Air E Master air valve for accessories F Air line filter P MufflerA Air supply line B Bleed-type master air valve required for pump C Air regulator D Air line quick disconnectPressure Relief Procedure Starting and Adjusting the PumpOperation Sanitizing the Pump Before First UseMaintenance Routine Cleaning of Product Contact Section of PumpMaintenance LubricationPreventive Maintenance Schedule Maintenance PersonOperator TaskMaintenance Troubleshooting TroubleshootingPROBLEM Follow Pressure Relief Proceerly/cleanly due to imbalance Leak in inlet or outlet sanitary fitLoose sanitary clamp Tighten clampService Repairing the Air ValveService DisassemblyReassembly 8. Install the valve carriage 105 so its tabs slip into the grooves on the narrow end of the actuator pis- tons 111. See FIG 3A Ball Check Assembly Check Valve RepairService For Sanitary Ball Check pumps remove ball gasket Sanitary Ball Check AssemblyFlapper Check Assembly TI8769aDiaphragm Repair Tools RequiredSanitary Pump 3A Pumpdiaphragm plate side high strength thread lock shaft sideBearing and Air Gasket Removal 310622L Pump Matrix 3150 Stainless Steel Sanitary Pumps1590 Stainless Steel Sanitary Pumps Pump MatrixSanitary Ball Check Valve Assembly Flapper Check Valve AssemblySanitary Diaphragm Assembly Parts DrawingParts List Pump Configuration Parts ListInlet and Outlet Parts List Parts ListDiaphragm Material Parts List Indicates replacement parts † Indicates a recommended spare partPart 3150Check Ball Material Parts List Indicates replacement parts † Indicates a recommended spare partcenter housing bore Apply medium strength adhesive to outsideApply a medium strength thread locker to screw threads and torque to 130-150 in-lbsFluid Section Parts Leak Detector and Pump Stand Parts ListAir Section Parts Accessories Accessories3150 Conversion Kits 15D990 Leak DetectorDimensional Drawing ModelModel TI8778aLoctite is a registered trademark of the Loctite Corporation Technical DataSantoprene is a registered trademark of the Monsanto Co Performance Chart 1590 3A Performance ChartTest Conditions Pump tested in water with inlet submerged To find Fluid Outlet PressureFlapper Check Valve Pumps 3A Ball Check Valve PumpsSanitary Ball Check Valve Pumps Technical Data 3150 3A Performance Chart Model Graco Standard Pump Warranty Extended Product WarrantyGraco Warranties Graco Information