Haier 3150 SF, 3150 SB Parts Drawing, 3A Pump Shown, Sanitary Ball Check Valve Assembly, 310622L

Page 26

Parts Drawing

3A Pump Shown

128

132

3 *240

2XA

3132

3*240

541

2XB

3*240

132

234

132

3*240 2XA

3132

3*240

541

2XB

3*240

132

129* 3

130

339*

Sanitary Ball Check

Valve Assembly

*242

*541

233

*240

TI7644a

3135

446*

Flapper Check Valve

Assembly

3*240

252

3232

2003 *250

*253

251

248

3 *240

TI4683a

Sanitary Diaphragm Assembly

135

444

143

446*

447*

445

TI4729c

445

1	Apply a high strength thread locker to
	diaphragm plate side of screw threads.
2	Apply a medium strength thread locker to

128

3 *129	130 3		*331

shaft side of screw threads.

3 Apply a waterproof sanitary lubricant to

clamps, clamping surfaces, and gaskets.

TI7645c

310622L

Image 26

Contents High Sanitation Pumps Model SA3AAA ShownInstructions/Parts List 310622LDimensional Drawing ContentsContents Technical DataFIRE AND EXPLOSION HAZARD WarningsWarnings PRESSURIZED EQUIPMENT HAZARDBURN HAZARD PERSONAL PROTECTIVE EQUIPMENTGeneral Information InstallationInstallation Leak Detection SystemAir Line Ground Wire ConnectionMountings Fluid Suction LineFluid Outlet Line Typical InstallationFIG. 3 Typical Floor-Mount Installation FIG. 4 Orientation of Fluid Ports Changing the Orientation of the Fluid Inlet and Outlet PortsAir Exhaust Ventilation A Air supply line B Bleed-type master air valve required for pump FIG. 5 Venting Exhaust AirE Master air valve for accessories F Air line filter P Muffler C Air regulator D Air line quick disconnectOperation Pressure Relief ProcedureStarting and Adjusting the Pump Sanitizing the Pump Before First UseMaintenance MaintenanceRoutine Cleaning of Product Contact Section of Pump LubricationOperator Preventive Maintenance ScheduleMaintenance Person TaskMaintenance PROBLEM TroubleshootingTroubleshooting Follow Pressure Relief ProceLoose sanitary clamp erly/cleanly due to imbalanceLeak in inlet or outlet sanitary fit Tighten clampService ServiceRepairing the Air Valve DisassemblyReassembly 8. Install the valve carriage 105 so its tabs slip into the grooves on the narrow end of the actuator pis- tons 111. See FIG 3A Ball Check Assembly Check Valve RepairFlapper Check Assembly Service For Sanitary Ball Check pumps remove ball gasketSanitary Ball Check Assembly TI8769aDiaphragm Repair Tools Requireddiaphragm plate side high strength thread lock Sanitary Pump3A Pump shaft sideBearing and Air Gasket Removal 310622L 1590 Stainless Steel Sanitary Pumps Pump Matrix3150 Stainless Steel Sanitary Pumps Pump MatrixSanitary Diaphragm Assembly Sanitary Ball Check Valve AssemblyFlapper Check Valve Assembly Parts DrawingInlet and Outlet Parts List Parts ListPump Configuration Parts List Parts ListPart Diaphragm Material Parts ListIndicates replacement parts † Indicates a recommended spare part 3150Check Ball Material Parts List Indicates replacement parts † Indicates a recommended spare partApply a medium strength thread locker to center housing boreApply medium strength adhesive to outside screw threads and torque to 130-150 in-lbsFluid Section Parts Leak Detector and Pump Stand Parts ListAir Section Parts 3150 Conversion Kits AccessoriesAccessories 15D990 Leak DetectorModel Dimensional DrawingModel TI8778aLoctite is a registered trademark of the Loctite Corporation Technical DataSantoprene is a registered trademark of the Monsanto Co Test Conditions Pump tested in water with inlet submerged Performance Chart1590 3A Performance Chart To find Fluid Outlet PressureFlapper Check Valve Pumps 3A Ball Check Valve PumpsSanitary Ball Check Valve Pumps Model 3150 3A Performance Chart Model Graco Warranties Graco Standard Pump WarrantyExtended Product Warranty Graco Information