Janome MB-4 manual Installing the RCS Unit optional item

Page 15

z x

r

Installing the RCS Unit (optional item)

zLoosen the thumbscrew and open the mounting arm. q Thumbscrew

w Mounting arm

t

q

w

x Loosen the screw knob A and set the RCS unit on

the mounting arm by hooking the RCS unit on the

pins.

Tighten the screw knob A to secure the RCS unit.

Adjust the angle of the mounting arm as desired and

tighten the thumbscrew.

e Screw knob A

c

v

y e

r

y

i

r RCS unit

t Pin

cLoosen the screw knob B on the end of the mounting arm and tilt the RCS unit to adjust the angle of the LCD screen for easier viewing.

Tighten the screw knob B to secure the RCS unit. y Screw knob B

vInsert the connector into the connector socket on the back of the machine.

Fold the cable and put it under the spool stand. u Connector

i Connector socket

NOTE:

u

q

You can connect the RCS unit when the machine is turned on. However do not connect the RCS unit while the machine is running or the LCD screen of the sub control panel is displaying a message.

If you are using the RCS unit on the tabletop, simply insert the connector into the connector socket on the back of the machine.

Extend the two legs on the backside of the RCS unit so that it rests on an angle for easier viewing.

qLeg

12

Image 15

Contents Instruction Book Important Safety Instructions Grounding Instructions Table of Contents Installing the Machine Setting UP the MachineRemoving the Head Stoppers Adjusting the feetPage Names of Parts RCS unit optional item Sub control panelOptional RCS unit Standard AccessoriesStandard Accessories Assembling the Spool Stand Setting the Thread Cones or Spools of Thread Setting the thread coneSetting the spool of thread Installing the Hoop Supporter Installing the RCS Unit optional item Grounding Instructions Connecting the Power SupplyDirect PC-Link Bobbin Threads NeedlesStabilizers Winding the Bobbin Inserting the bobbin Removing the bobbin caseInserting the bobbin case Threading needle No.1 Threading the Needle⁄22 Threading the needle with the needle threader Setting the Fabric in the Embroidery Hoop Adjusting the Hoop Supporter for Optional Hoops Setting the Embroidery HoopStart/Stop button Mode buttonLCD brightness adjusting dial Machine operating buttonsLCD screen Y uNeedle bar number setting Machine SettingsStitch count setting Color section layer settingStarting to Embroider N1253 N2224HM1 ? M1 02010 02/13 Removing the Hoop Tension is too tight Adjusting the Thread TensionAdjusting the needle thread tension Adjusting the bobbin thread tensionReplacing the Needle Checking the needleReplacing the needle Basic Operation of the Optional RCS Unit SET key Function keysMenu key File open keyOn-screen Help Movie Disconnecting the RCS Unit Selecting the Embroidery Patterns Advanced Operation with the Optional RCS UnitSelecting the built-in designs Function keys circle keys Color list optionAutomatic color assignment Manual color assignment Monogramming Letter case Function keys Font selectionLettering orientation Letter sizeSaving the monogram Entering the charactersTo insert a character Correcting the text To delete a characterPlacement of monogramming Horizontal orientationVertical orientation Multi-color monogramming Editing Resizing the pattern Editing FunctionsSelecting the hoop Moving the patternRotating the pattern Deleting the patternSaving the file Flipping the pattern Duplicating the patternMonogramming in an arc To customize the colors of the pattern image Customizing the color settingCombining the Patterns and Lettering ⁄2 Edit Bright Blue Trac Outline M2126X110mm Machine ID number Customizing the Setting with the Sub Control PanelEco mode setting Buzzer sound controlThread selection Resetting all to defaultsFormatting the memory Maximum sewing speedIgnoring short stitches Setting the trim tail lengthSetting the thread detector sensitivity Reminder message ON/OFFJump thread trimming threshold Jump thread trimming ON/OFFCustomizing the Settings with the Optional RCS Unit LCD brightness adjustmentInch/mm option Touch screen calibration Screen saverMachine ID and name Yes ⁄1Grid size ⁄2Maximum sewing speed⁄3Hoop selection for monogramming ⁄5Screen color options ⁄4Selecting the thread brand⁄6Reminder message ON/OFF ⁄7Reserving the color for the needle bar⁄8Ignoring short stitches ¤1Jump thread trimming ON/OFF ⁄9Setting the trim tail length¤0Setting the thread detector sensitivity ¤2Setting the number of jumps for trimming¤3Language selection Saving the Pattern as a File File ManagementCreating a new folder Opening a file Deleting the file Deleting the folderOpening the embroidery pattern from the PC Design card PC Design CardsInserting the PC Design card Ejecting the PC Design cardOpening the embroidery pattern from the USB memory USB MemoryOpening the embroidery pattern from the CD-ROM CD-ROM DriveCleaning the Bobbin Case Cleaning the HookCleaning the Auto Thread Cutter Mechanism Oiling Error Messages Audible SignalsAudible signal Buzzer sounds when Problem Cause Reference TroubleshootingTroubleshooting