Janome MB-4 manual Important Safety Instructions

Page 2

IMPORTANT SAFETY INSTRUCTIONS

The machine is not intended for use by children or mentally infirm persons without proper supervision.

This machine is designed and manufactured for household use.

When using an electrical appliance, basic safety precautions should always be followed, including the followings: Read all instructions before using this machine.

DANGER To reduce the risk of electric shock:

1.The machine should never be left unattended when plugged in. Always unplug this machine from the electric outlet immediately after using and before cleaning.

WARNING To reduce the risk of burns, fire, electric shock, or injury to persons:

1.Do not allow the machine to be used as a toy. Close attention is necessary when this machine is used by or children.

2.Use this machine only for its intended use as described in this instruction book.

3.Never operate this machine if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water.

Return this machine to the nearest authorized dealer or service center for examination, repair, electrical or mechanical adjustment.

4.Never operate this machine with any air openings blocked. Keep ventilation openings of this machine free from accumulation of lint, dust and loose cloth.

5.Never drop or insert any object into any opening.

6.Do not use outdoors.

7.Do not operate where aerosol (spray) products are being used or where oxygen is being administered.

8.Connect this machine to a properly grounded outlet only. See Grounding Instructions.

9.To disconnect, turn all controls to the off (“O”) position, then remove plug from outlet.

10.Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

11.Keep fingers away from all moving parts. Special care is required around the machine needle.

12.Do not use bent needles.

13.Do not hold the embroidery hoop while stitching. It may deflect the needle causing it to break.

14.Switch the machine off (“o”) when making any adjustment in the needle area, such as threading the needle with your hand, changing the needle, inserting the bobbin, and the like.

15.Always unplug this machine from the electrical outlet when making any adjustments mentioned in this instruction book.

SAVE THESE INSTRUCTIONS

The design and specifications are subject to change without a prior notice.

Please note that on disposal, this product must be safely recycled in accordance with relevant National legislation relating to electrical/electronic products. If in doubt please contact your retailer

for guidance. (European Union only)

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Instruction Book Important Safety Instructions Grounding Instructions Table of Contents Setting UP the Machine Installing the MachineAdjusting the feet Removing the Head StoppersPage Names of Parts Sub control panel RCS unit optional itemStandard Accessories Optional RCS unitStandard Accessories Assembling the Spool Stand Setting the spool of thread Setting the Thread Cones or Spools of ThreadSetting the thread cone Installing the Hoop Supporter Installing the RCS Unit optional item Connecting the Power Supply Grounding InstructionsDirect PC-Link Stabilizers Bobbin ThreadsNeedles Winding the Bobbin Removing the bobbin case Inserting the bobbinInserting the bobbin case Threading the Needle Threading needle No.1⁄22 Threading the needle with the needle threader Setting the Fabric in the Embroidery Hoop Setting the Embroidery Hoop Adjusting the Hoop Supporter for Optional HoopsMachine operating buttons Mode buttonLCD brightness adjusting dial Start/Stop buttonY u LCD screenColor section layer setting Machine SettingsStitch count setting Needle bar number settingN1253 N2224 Starting to EmbroiderHM1 ? M1 02010 02/13 Removing the Hoop Adjusting the bobbin thread tension Adjusting the Thread TensionAdjusting the needle thread tension Tension is too tightReplacing the needle Replacing the NeedleChecking the needle Basic Operation of the Optional RCS Unit File open key Function keysMenu key SET keyOn-screen Help Movie Disconnecting the RCS Unit Advanced Operation with the Optional RCS Unit Selecting the Embroidery PatternsSelecting the built-in designs Automatic color assignment Function keys circle keysColor list option Manual color assignment Monogramming Letter size Function keys Font selectionLettering orientation Letter caseEntering the characters Saving the monogramCorrecting the text To delete a character To insert a characterVertical orientation Placement of monogrammingHorizontal orientation Multi-color monogramming Editing Moving the pattern Editing FunctionsSelecting the hoop Resizing the patternSaving the file Rotating the patternDeleting the pattern Duplicating the pattern Flipping the patternMonogramming in an arc Customizing the color setting To customize the colors of the pattern imageCombining the Patterns and Lettering ⁄2 Edit Bright Blue Trac Outline M2126X110mm Buzzer sound control Customizing the Setting with the Sub Control PanelEco mode setting Machine ID numberMaximum sewing speed Resetting all to defaultsFormatting the memory Thread selectionReminder message ON/OFF Setting the trim tail lengthSetting the thread detector sensitivity Ignoring short stitchesJump thread trimming ON/OFF Jump thread trimming thresholdInch/mm option Customizing the Settings with the Optional RCS UnitLCD brightness adjustment Screen saver Touch screen calibrationMachine ID and name Yes ⁄3Hoop selection for monogramming ⁄1Grid size⁄2Maximum sewing speed ⁄4Selecting the thread brand ⁄5Screen color options⁄8Ignoring short stitches ⁄6Reminder message ON/OFF⁄7Reserving the color for the needle bar ¤2Setting the number of jumps for trimming ⁄9Setting the trim tail length¤0Setting the thread detector sensitivity ¤1Jump thread trimming ON/OFF¤3Language selection File Management Saving the Pattern as a FileCreating a new folder Opening a file Deleting the folder Deleting the fileEjecting the PC Design card PC Design CardsInserting the PC Design card Opening the embroidery pattern from the PC Design cardUSB Memory Opening the embroidery pattern from the USB memoryCD-ROM Drive Opening the embroidery pattern from the CD-ROMCleaning the Hook Cleaning the Bobbin CaseCleaning the Auto Thread Cutter Mechanism Oiling Audible signal Buzzer sounds when Error MessagesAudible Signals Troubleshooting Problem Cause ReferenceTroubleshooting
Top Page Image Contents