Janome MB-4 manual HM1 ? M1 02010 02/13

Page 31

b

u

n

o

y

H:M1 ?

M1 02010 02/13 2

i

!0

bPress the START/STOP button, the LCD screen will show the reminder asking you to confirm the hoop type to be used.

y START/STOP button u Reminder display

NOTE:

If you press the START/STOP button when the tension release lever is in the open position, a warning sign [W:03] will appear.

Pull the tension release lever up to close the tension disk.

Check the hoop size and press the START/ STOP button again to sew a few stitches.

nPress the START/STOP button to stop the machine.

Trim the thread at the beginning.

Then, press the START/STOP button again. The machine will sew up to the fourth color and stop automatically.

Re-thread each needle with the next color and press the START/STOP button to continue sewing.

If the thread breaks or runs out while stitching, the machine will automatically stop and the hoop will go back to the position where the thread broke or ran out.

However, you can fine-tune the restarting position by moving the hoop.

Press the ENTER button to select the stitch count setting.

iENTER button

Press the upward arrow button to move the hoop forward 10 stitches.

oUpward arrow button

Press the downward arrow button to move the hoop backward 10 stitches.

!0Downward arrow button

28

Image 31

Contents Instruction Book Important Safety Instructions Grounding Instructions Table of Contents Installing the Machine Setting UP the MachineRemoving the Head Stoppers Adjusting the feetPage Names of Parts RCS unit optional item Sub control panelOptional RCS unit Standard AccessoriesStandard Accessories Assembling the Spool Stand Setting the thread cone Setting the Thread Cones or Spools of ThreadSetting the spool of thread Installing the Hoop Supporter Installing the RCS Unit optional item Grounding Instructions Connecting the Power SupplyDirect PC-Link Needles Bobbin ThreadsStabilizers Winding the Bobbin Inserting the bobbin Removing the bobbin caseInserting the bobbin case Threading needle No.1 Threading the Needle⁄22 Threading the needle with the needle threader Setting the Fabric in the Embroidery Hoop Adjusting the Hoop Supporter for Optional Hoops Setting the Embroidery HoopStart/Stop button Mode buttonLCD brightness adjusting dial Machine operating buttonsLCD screen Y uNeedle bar number setting Machine SettingsStitch count setting Color section layer settingStarting to Embroider N1253 N2224HM1 ? M1 02010 02/13 Removing the Hoop Tension is too tight Adjusting the Thread TensionAdjusting the needle thread tension Adjusting the bobbin thread tensionChecking the needle Replacing the NeedleReplacing the needle Basic Operation of the Optional RCS Unit SET key Function keysMenu key File open keyOn-screen Help Movie Disconnecting the RCS Unit Selecting the Embroidery Patterns Advanced Operation with the Optional RCS UnitSelecting the built-in designs Color list option Function keys circle keysAutomatic color assignment Manual color assignment Monogramming Letter case Function keys Font selectionLettering orientation Letter sizeSaving the monogram Entering the charactersTo insert a character Correcting the text To delete a characterHorizontal orientation Placement of monogrammingVertical orientation Multi-color monogramming Editing Resizing the pattern Editing FunctionsSelecting the hoop Moving the patternDeleting the pattern Rotating the patternSaving the file Flipping the pattern Duplicating the patternMonogramming in an arc To customize the colors of the pattern image Customizing the color settingCombining the Patterns and Lettering ⁄2 Edit Bright Blue Trac Outline M2126X110mm Machine ID number Customizing the Setting with the Sub Control PanelEco mode setting Buzzer sound controlThread selection Resetting all to defaultsFormatting the memory Maximum sewing speedIgnoring short stitches Setting the trim tail lengthSetting the thread detector sensitivity Reminder message ON/OFFJump thread trimming threshold Jump thread trimming ON/OFFLCD brightness adjustment Customizing the Settings with the Optional RCS UnitInch/mm option Touch screen calibration Screen saverMachine ID and name Yes ⁄2Maximum sewing speed ⁄1Grid size⁄3Hoop selection for monogramming ⁄5Screen color options ⁄4Selecting the thread brand⁄7Reserving the color for the needle bar ⁄6Reminder message ON/OFF⁄8Ignoring short stitches ¤1Jump thread trimming ON/OFF ⁄9Setting the trim tail length¤0Setting the thread detector sensitivity ¤2Setting the number of jumps for trimming¤3Language selection Saving the Pattern as a File File ManagementCreating a new folder Opening a file Deleting the file Deleting the folderOpening the embroidery pattern from the PC Design card PC Design CardsInserting the PC Design card Ejecting the PC Design cardOpening the embroidery pattern from the USB memory USB MemoryOpening the embroidery pattern from the CD-ROM CD-ROM DriveCleaning the Bobbin Case Cleaning the HookCleaning the Auto Thread Cutter Mechanism Oiling Audible Signals Error MessagesAudible signal Buzzer sounds when Problem Cause Reference TroubleshootingTroubleshooting