Multiquip HTN-27K-TCSL operation manual HTN-SERIES General Information, Engine Blades

Page 17

HTN-SERIES — GENERAL INFORMATION

HTN SERIES Ride-On PowerTrowel Familiarization

The HTN SERIES Ride-On Power Trowel is designed for the floating and finishing of concrete slabs.

Take a walk around your trowel. Take notice of all the major components (see Figures 2 and 3, pages 18 and 19) like the engine, blades, air cleaner, fuel system, fuel shut-off valve, ignition switch etc. Ensure engine and gearbox oil levels are within proper operating range.

Read all the safety instructions carefully. Safety instructions will be found throughout this manual and on the machine. Keep all safety information in good, readable condition. Operators should be well trained on the operation and maintenance of the trowel.

Look at the operator control levers. Grasp the control levers and move them around a bit. Observe how moving the control levers cause the gearboxes and frame to move.

Notice the foot pedal which controls the engine and blade speed. Also take a look at the main driveline of the trowel. Take note and reference how the belts look, this is the way the belts should look when adjusted properly.

Before using your trowel, test it on a flat watered down section of finished concrete.This trial test run will increase your confidence in using the trowel and at the same time it will familiarize you with the trowel’s controls and indicators. In addition you will understand how the trowel will handle under actual conditions.

Engine

This trowel is equipped with an air cooled 27HP or 28HP EFI Kohler gasoline engine. Refer to the engine owner’s manual for specific instructions regarding engine operation.This manual is included with the trowel at the time of shipping. Please contact your nearest Multiquip Dealer if a replacement manual is required.

Blades

The blades of the trowel finish the concrete as they are swirled around the surface. Blades are classified as combination (10 or 8 inches wide) and finish (6 inches wide).This trowel is equipped with four blades per rotor equally spaced in a radial pattern and attached to a vertical rotating shaft by means of a spider assembly.

Figures 2 and 3 show the location of the controls, indicators and general maintenance parts. Each control may perform more than one function.The functions of the controls or indicators are on pages 18 and 19.

HTN- SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Model HTN-27K-TCSL Model HTN-28K-TCSL Page Silicosis Warning Table of Contents Order via Fax Dealers Only Best Deal! Order via Internet Dealers OnlyMachine layout, location of components, checking of engine Training ChecklistTraining Checklist Daily PRE-OPERATION Checklist Daily PRE-OPERATION ChecklistYou can be Injured if you do not follow these directions HTN-SERIES Safety Message Alert SymbolsAlways wear approved eye and hearing protection Always wear approved respiratory protectionDo not operate or service this equipment SafetyRules for Safe Operation Fatigue, illness or taking medicineLifting the Ride-On Trowel Always keep the work area well organizedBattery Towing Safety PrecautionsHTN-SERIES Rules for Safe Operation TransportingAlways know the location of the nearest first aid kit Maintenance SafetyEmergencies Machine Safety Decals HTN-SERIES Operation and Safety DecalsHTN-SERIES- Specifications Trowel HTN-Series Engine Specifications HTN-SERIES- Specifications EngineEngine Blades HTN Series Ride-On PowerTrowel FamiliarizationHTN-SERIES General Information HTN-SERIES Controls and Indicators HTN-SERIES Controls and Indicators Initial Servicing HTN-SERIES Basic EngineKohler 28 HP Engine Kohler 27 HP Engine Control Handle Assembly Trowel Pre-Set Up InstructionsSeat Assembly Battery SetupGearbox Oil Level HTN-SERIES Initial START-UPEngine Oil Level Always check engine oil Before Each USE Fuel Gauge Important Information Before You Start HTN-SERIES OperationSteering HTN-SERIES OperationMaintenance Schedule HTN-SERIES MaintenanceReinstall the air cleaner cover and secure the latches HTN-SERIES MaintenanceAir Cleaner Daily Disassembly and Reassembly Standard Type Air Cleaner Components to CheckMake sure the cooling shrouds are reinstalled Make sure the correct depth airOil Filter 100 Hours Changing Engine Oil And FilterFuel Filter 200 Hours Oil And Fuel LinesHave a 3/4 X 1 X 3-1/4 inch wooden block available Checking The Drive BeltRemoving the Drive Belt Reinstall the spare belt carrier and the drive belt guard HTN-SERIES- MaintenanceInstalling the Drive Belt Using Replacement Drive Belt Wooden BlockSpare Drive Belt Replacement HTN-SERIES- MaintenanceTorque Converter/Variable Pitch Pulley Drive Pulley Drive System Theory of OperationClutch How It Works Figure Condition a z Engine IdlingBlade Pitch Matching Blade Pitch for Both Sets of BladesStabilizer Ring Removal Trowel Arm adjustment ProcedureRemove the trowel arm from the spider plate Trowel Arm RemovalTrowel Blade Removal Spider Plate Hex Head Bolt Zerk FittingSideview Trowel Arm AdjustmentChecking Trowel Arm Straightness Re-Assembly Trowel Arm Adjustment SetupDecommissioning Trowel/Components Installing Pans Onto Finisher BladesSymptom Possible Problem Solution HTN-SERIES -TROUBLESHOOTING Engine HTN-SERIES-TROUBLESHOOTING Trowel Troubleshooting HTN-SERIES-TROUBLESHOOTING TrowelHTN-SERIES Notes Payment Terms Page Mexico United Kingdom United StatesCanada Brazil Your Local Dealer is

HTN-27K-TCSL specifications

The Multiquip HTN-27K-TCSL is a cutting-edge piece of technology designed for professionals in the construction and industrial sectors. This portable hydraulic power unit is known for its robust performance and versatility, making it an ideal choice for a wide range of applications.

One of the standout features of the HTN-27K-TCSL is its powerful engine. Equipped with a reliable 27-horsepower Kohler engine, this unit ensures maximum efficiency and performance, allowing operators to complete tasks quickly and effectively. The engine is designed to be both fuel-efficient and environmentally friendly, adhering to emission regulations without sacrificing power.

The HTN-27K-TCSL boasts a unique hydraulic system that delivers high-pressure flow rates, making it suitable for operating multiple tools simultaneously. With a maximum hydraulic pressure of 3,000 PSI, this power unit can effortlessly handle demanding tasks such as concrete breaking, water jetting, and other heavy-duty applications. The ability to provide consistent hydraulic power allows for enhanced productivity on job sites.

In terms of versatility, the Multiquip HTN-27K-TCSL is equipped with a wide range of output options. Its hydraulic outlet configurations can support various attachments, enabling users to adapt the unit for diverse tasks. This flexibility makes it an invaluable tool for contractors, landscapers, and utility companies.

Another notable characteristic of the HTN-27K-TCSL is its rugged construction. Built to withstand the rigors of tough job sites, this hydraulic power unit features a durable frame and protective covers that shield the engine and components from dust and debris. The compact design ensures easy transportation and maneuverability, making it a practical choice for both indoor and outdoor use.

Additionally, the HTN-27K-TCSL is designed with operator safety in mind. It features a user-friendly interface, with clearly labeled controls for easy operation. Safety features such as emergency shut-off switches and protective guards further enhance its usability, ensuring that operators can work confidently.

In summary, the Multiquip HTN-27K-TCSL is a powerful, versatile, and robust hydraulic power unit designed to meet the demanding needs of various industries. With its exceptional performance, durable construction, and focus on safety, it continues to be a trusted choice among professionals seeking reliable hydraulic solutions.
Top Page Image Contents