Multiquip HTN-27K-TCSL HTN-SERIES Operation, Fuel Gauge Important Information Before You Start

Page 23

HTN-SERIES — OPERATION

5.When starting a cold engine, pull the choke knob, if so equipped, (Figure 9) out to the closed position. In warm weather or when the engine is warm, the unit can be started with choke halfway or completely open. (27 HP engine)

Figure 7. Fuel Gauge

Important Information Before You Start

1.This ride-on trowel is equipped with a safety "safety stop switch". This switch is located beneath the seat assembly. Remember the engine will not start unless an operator is sitting in the operator’s seat. The weight of an operator depresses an electrical switch which will allow the engine to start.

WARNING

NEVER disable or disconnect the "safety stop switch". It is provided for the operator's safety and injury or death may result if it is disabled, disconnected or improperly maintained.

2.The safety stop switch should be used to stop the engine after every use. Doing this will verify the switch is working properly thus providing safety for the operator.Remember to turn the key to the “OFF” position after stopping the machine. Not doing so will drain the battery.

3.The right foot pedal (Figure 8) controls blade and engine speed.The position of the foot pedal determines the blade speed. Slow blade speed is obtained by slightly depressing the pedal. Maximum blade speed is obtained by fully depressing the pedal.

Figure 9. Choke Knob (Kohler 27 HP only)

6.Keep your foot OFF the blade speed control pedal and in all circumstances, start the engine at idle (without touching the pedal).

7.Insert the ignition key into the ignition switch.

8.Turn the ignition key (Figure 10) clockwise and listen for the engine to start. Once the engine starts release ignition key.

9.If the engine fails to start in this manner, consult the engine owner's manual supplied with the trowel.

10.Test the safety stop switch by standing up briefly.The switch under the seat should cause the engine to stop. If the switch fails to shut down the engine.Turn off the engine with the key switch and repair the safety stop switch. See Table 7 (Troubleshooting ) for possible causes.

Figure 8. Blade Speed Control Foot Pedal

Starting the Engine

1.With one foot on the ground and the other foot placed on the trowel's platform, grab the frame near the seat and lift yourself onto the trowel. Sit in the operator's seat and ensure the control handles, foot pedal and control panel items can be comfortably accessed.

Figure 10. Ignition Key

11.Let the engine idle for 3-5 minutes. If choke is applied, push the choke to the open position as soon as the engine will run smoothly.

HTN- SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model HTN-27K-TCSL Model HTN-28K-TCSL Page Silicosis Warning Table of Contents Order via Fax Dealers Only Best Deal! Order via Internet Dealers OnlyMachine layout, location of components, checking of engine Training ChecklistTraining Checklist Daily PRE-OPERATION Checklist Daily PRE-OPERATION ChecklistYou can be Injured if you do not follow these directions HTN-SERIES Safety Message Alert SymbolsAlways wear approved eye and hearing protection Always wear approved respiratory protectionFatigue, illness or taking medicine SafetyDo not operate or service this equipment Rules for Safe OperationLifting the Ride-On Trowel Always keep the work area well organizedTransporting Towing Safety PrecautionsBattery HTN-SERIES Rules for Safe OperationAlways know the location of the nearest first aid kit Maintenance SafetyEmergencies Machine Safety Decals HTN-SERIES Operation and Safety DecalsHTN-SERIES- Specifications Trowel HTN-Series Engine Specifications HTN-SERIES- Specifications EngineEngine Blades HTN Series Ride-On PowerTrowel FamiliarizationHTN-SERIES General Information HTN-SERIES Controls and Indicators HTN-SERIES Controls and Indicators Initial Servicing HTN-SERIES Basic EngineKohler 28 HP Engine Kohler 27 HP Engine Battery Setup Trowel Pre-Set Up InstructionsControl Handle Assembly Seat AssemblyGearbox Oil Level HTN-SERIES Initial START-UPEngine Oil Level Always check engine oil Before Each USE Fuel Gauge Important Information Before You Start HTN-SERIES OperationSteering HTN-SERIES OperationMaintenance Schedule HTN-SERIES MaintenanceReinstall the air cleaner cover and secure the latches HTN-SERIES MaintenanceAir Cleaner Daily Make sure the correct depth air Air Cleaner Components to CheckDisassembly and Reassembly Standard Type Make sure the cooling shrouds are reinstalledOil And Fuel Lines Changing Engine Oil And FilterOil Filter 100 Hours Fuel Filter 200 HoursHave a 3/4 X 1 X 3-1/4 inch wooden block available Checking The Drive BeltRemoving the Drive Belt Wooden Block HTN-SERIES- MaintenanceReinstall the spare belt carrier and the drive belt guard Installing the Drive Belt Using Replacement Drive BeltSpare Drive Belt Replacement HTN-SERIES- MaintenanceTorque Converter/Variable Pitch Pulley Drive Pulley Drive System Theory of OperationMatching Blade Pitch for Both Sets of Blades How It Works Figure Condition a z Engine IdlingClutch Blade PitchStabilizer Ring Removal Trowel Arm adjustment ProcedureSpider Plate Hex Head Bolt Zerk Fitting Trowel Arm RemovalRemove the trowel arm from the spider plate Trowel Blade RemovalSideview Trowel Arm AdjustmentChecking Trowel Arm Straightness Re-Assembly Trowel Arm Adjustment SetupDecommissioning Trowel/Components Installing Pans Onto Finisher BladesSymptom Possible Problem Solution HTN-SERIES -TROUBLESHOOTING Engine HTN-SERIES-TROUBLESHOOTING Trowel Troubleshooting HTN-SERIES-TROUBLESHOOTING TrowelHTN-SERIES Notes Payment Terms Page Your Local Dealer is United StatesMexico United Kingdom Canada Brazil

HTN-27K-TCSL specifications

The Multiquip HTN-27K-TCSL is a cutting-edge piece of technology designed for professionals in the construction and industrial sectors. This portable hydraulic power unit is known for its robust performance and versatility, making it an ideal choice for a wide range of applications.

One of the standout features of the HTN-27K-TCSL is its powerful engine. Equipped with a reliable 27-horsepower Kohler engine, this unit ensures maximum efficiency and performance, allowing operators to complete tasks quickly and effectively. The engine is designed to be both fuel-efficient and environmentally friendly, adhering to emission regulations without sacrificing power.

The HTN-27K-TCSL boasts a unique hydraulic system that delivers high-pressure flow rates, making it suitable for operating multiple tools simultaneously. With a maximum hydraulic pressure of 3,000 PSI, this power unit can effortlessly handle demanding tasks such as concrete breaking, water jetting, and other heavy-duty applications. The ability to provide consistent hydraulic power allows for enhanced productivity on job sites.

In terms of versatility, the Multiquip HTN-27K-TCSL is equipped with a wide range of output options. Its hydraulic outlet configurations can support various attachments, enabling users to adapt the unit for diverse tasks. This flexibility makes it an invaluable tool for contractors, landscapers, and utility companies.

Another notable characteristic of the HTN-27K-TCSL is its rugged construction. Built to withstand the rigors of tough job sites, this hydraulic power unit features a durable frame and protective covers that shield the engine and components from dust and debris. The compact design ensures easy transportation and maneuverability, making it a practical choice for both indoor and outdoor use.

Additionally, the HTN-27K-TCSL is designed with operator safety in mind. It features a user-friendly interface, with clearly labeled controls for easy operation. Safety features such as emergency shut-off switches and protective guards further enhance its usability, ensuring that operators can work confidently.

In summary, the Multiquip HTN-27K-TCSL is a powerful, versatile, and robust hydraulic power unit designed to meet the demanding needs of various industries. With its exceptional performance, durable construction, and focus on safety, it continues to be a trusted choice among professionals seeking reliable hydraulic solutions.
Top Page Image Contents