Multiquip HTN-27K-TCSL operation manual Trowel Arm Adjustment Setup, Re-Assembly

Page 37

HTN-SERIES — MAINTENANCE

Figure 38. Trowel Arm Adjustment Setup

3.Unscrew the locking bolts on the adjustment tool and place the trowel arm into the fixture channel as shown in Figure 39 A thin shim may be required to cover the blade holes on the trowelarm. Makesuretoalignthetroweladjustmentboltwith the fixture adjustment bolt.

1Arm

2Trowel Arm Lever

3Fixture Arm

4Adjustment Bolt

5Distance = .010 Inch

6Adjustment Bolt

7Trowel Arm Adjustment Fixture

8Locking Bolts

9Shim

Figure 39. Trowel Arm Adjustment Fixture Components

4.Use an allen wrench to tighten the locking bolts securing the trowel arm in place.

5.Adjust the bolt "distance" shown in Figure 37 to match one of the arms. The other arms will be adjusted to match this distance.

6.Loosen the locking nut on the trowel arm lever, then turn the trowel arm adjusting bolt until it barely touches (.010") the fixture adjusting bolt.

7.Oncethecorrectadjustmentismade,tightenthelocknuton the trowel arm to lock in place.

8.Loosen locking nuts on the adjustment fixture, and remove trowel arm.

9.Repeat steps for the remaining trowel arms.

Re-Assembly

1.Clean and examine the upper/lower wear plates and thrust collar.Examine the entire spider assembly.Wire brush any concreteorrustbuild-up.Ifanyofthespider componentsare found to be damaged or out of round, replace them.

2.Makesurethatthebronzetrowelarmbushingisnotdamage or out of round.Clean the bushing if necessary.If the bronze bushing is damaged or worn, replace it.

3.Reinstall bronze bushing onto trowel arm.

4.Repeat steps 2 -3 for each trowel arm.

5.Make sure that the spring tensioner is in the correct position to exert tension on the trowel arm.

6.Insertalltrowelarmswithleversintospiderplate(withbronze bushingalreadyinstalled)usingcaretoaligngreaseholeon bronze bushing with grease hole fitting on spider plate.

7.Locktrowelarmsinplacebytighteningthehexheadboltwith zerk grease fitting and jam nut.

8.Re-install the blades onto the trowel arms.

9.Install stabilizer ring onto spider assembly.

10.Lubricate all grease points (zerk fittings) with premium "Lithum 12" based grease, conforming to NLG1 Grade #2 consistency.

HTN- SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Model HTN-27K-TCSL Model HTN-28K-TCSL Page Silicosis Warning Table of Contents Order via Fax Dealers Only Best Deal! Order via Internet Dealers OnlyTraining Checklist Training ChecklistMachine layout, location of components, checking of engine Daily PRE-OPERATION Checklist Daily PRE-OPERATION ChecklistYou can be Injured if you do not follow these directions HTN-SERIES Safety Message Alert SymbolsAlways wear approved eye and hearing protection Always wear approved respiratory protectionDo not operate or service this equipment SafetyRules for Safe Operation Fatigue, illness or taking medicineLifting the Ride-On Trowel Always keep the work area well organizedBattery Towing Safety PrecautionsHTN-SERIES Rules for Safe Operation TransportingEmergencies Maintenance SafetyAlways know the location of the nearest first aid kit Machine Safety Decals HTN-SERIES Operation and Safety DecalsHTN-SERIES- Specifications Trowel HTN-Series Engine Specifications HTN-SERIES- Specifications EngineHTN-SERIES General Information HTN Series Ride-On PowerTrowel FamiliarizationEngine Blades HTN-SERIES Controls and Indicators HTN-SERIES Controls and Indicators Kohler 28 HP Engine Kohler 27 HP Engine HTN-SERIES Basic EngineInitial Servicing Control Handle Assembly Trowel Pre-Set Up InstructionsSeat Assembly Battery SetupEngine Oil Level Always check engine oil Before Each USE HTN-SERIES Initial START-UPGearbox Oil Level Fuel Gauge Important Information Before You Start HTN-SERIES OperationSteering HTN-SERIES OperationMaintenance Schedule HTN-SERIES MaintenanceAir Cleaner Daily HTN-SERIES MaintenanceReinstall the air cleaner cover and secure the latches Disassembly and Reassembly Standard Type Air Cleaner Components to CheckMake sure the cooling shrouds are reinstalled Make sure the correct depth airOil Filter 100 Hours Changing Engine Oil And FilterFuel Filter 200 Hours Oil And Fuel LinesRemoving the Drive Belt Checking The Drive BeltHave a 3/4 X 1 X 3-1/4 inch wooden block available Reinstall the spare belt carrier and the drive belt guard HTN-SERIES- MaintenanceInstalling the Drive Belt Using Replacement Drive Belt Wooden BlockSpare Drive Belt Replacement HTN-SERIES- MaintenanceTorque Converter/Variable Pitch Pulley Drive Pulley Drive System Theory of OperationClutch How It Works Figure Condition a z Engine IdlingBlade Pitch Matching Blade Pitch for Both Sets of BladesStabilizer Ring Removal Trowel Arm adjustment ProcedureRemove the trowel arm from the spider plate Trowel Arm RemovalTrowel Blade Removal Spider Plate Hex Head Bolt Zerk FittingChecking Trowel Arm Straightness Trowel Arm AdjustmentSideview Re-Assembly Trowel Arm Adjustment SetupDecommissioning Trowel/Components Installing Pans Onto Finisher BladesSymptom Possible Problem Solution HTN-SERIES -TROUBLESHOOTING Engine HTN-SERIES-TROUBLESHOOTING Trowel Troubleshooting HTN-SERIES-TROUBLESHOOTING TrowelHTN-SERIES Notes Payment Terms Page Mexico United Kingdom United StatesCanada Brazil Your Local Dealer is

HTN-27K-TCSL specifications

The Multiquip HTN-27K-TCSL is a cutting-edge piece of technology designed for professionals in the construction and industrial sectors. This portable hydraulic power unit is known for its robust performance and versatility, making it an ideal choice for a wide range of applications.

One of the standout features of the HTN-27K-TCSL is its powerful engine. Equipped with a reliable 27-horsepower Kohler engine, this unit ensures maximum efficiency and performance, allowing operators to complete tasks quickly and effectively. The engine is designed to be both fuel-efficient and environmentally friendly, adhering to emission regulations without sacrificing power.

The HTN-27K-TCSL boasts a unique hydraulic system that delivers high-pressure flow rates, making it suitable for operating multiple tools simultaneously. With a maximum hydraulic pressure of 3,000 PSI, this power unit can effortlessly handle demanding tasks such as concrete breaking, water jetting, and other heavy-duty applications. The ability to provide consistent hydraulic power allows for enhanced productivity on job sites.

In terms of versatility, the Multiquip HTN-27K-TCSL is equipped with a wide range of output options. Its hydraulic outlet configurations can support various attachments, enabling users to adapt the unit for diverse tasks. This flexibility makes it an invaluable tool for contractors, landscapers, and utility companies.

Another notable characteristic of the HTN-27K-TCSL is its rugged construction. Built to withstand the rigors of tough job sites, this hydraulic power unit features a durable frame and protective covers that shield the engine and components from dust and debris. The compact design ensures easy transportation and maneuverability, making it a practical choice for both indoor and outdoor use.

Additionally, the HTN-27K-TCSL is designed with operator safety in mind. It features a user-friendly interface, with clearly labeled controls for easy operation. Safety features such as emergency shut-off switches and protective guards further enhance its usability, ensuring that operators can work confidently.

In summary, the Multiquip HTN-27K-TCSL is a powerful, versatile, and robust hydraulic power unit designed to meet the demanding needs of various industries. With its exceptional performance, durable construction, and focus on safety, it continues to be a trusted choice among professionals seeking reliable hydraulic solutions.
Top Page Image Contents