Multiquip HTN-27K-TCSL operation manual Checking The Drive Belt, Removing the Drive Belt

Page 29

Checking The Drive Belt

The drive belt needs to be replaced as soon as it starts to show signs of wear. Indications of excessive belt wear are fraying, squealing when in use, belts that emit smoke or a burning rubber smell when in use.

Under normal operating conditions, a drive belt may last approximately 150 hours. If your trowel is not reaching this kind of life span for drive belt wear, check the drive belt for proper pulley alignment and spacing.

To gain access to the drive belt, remove the drive belt guard cover (item 1 Figure 17), then visually inspect the drive belt for signs of damage or excessive wear. If the drive belt is worn or damaged, replace the drive belt.

WARNING

DO NOT attempt to insert hands or tools into the belt area while the engine is running. NEVER run the engine with the safety guards removed. Keep fingers, hands, hair and clothing away from all moving parts to prevent bodily injury.

HTN-SERIES — MAINTENANCE

5

3

2

4

1

1Drive Belt Guard Cover

2Lower Pulley

3Upper Pulley

4Spare Drive Belt

5Spare Drive Belt Holder

Figure 17. Drive Belt Guard Cover

1.Remove Drive Belt Guard Cover (item 1 Figure 17).

2.Squeeze the drive belt as shown in Figure 18, and pull the V-belt upwards.This will spread open the faces of the lower drive pulley.

WARNING

DO NOT remove the drive belt guard cover until the muffler has cooled. Allow the entire trowel to cool down before performing this procedure.

1

2

Removing the Drive Belt

zLeave the existing drive belt intact until instructed to cut it.

zLeave the engine in place for this procedure. It is not necessary to slide the engine to replace the drive belt.

zHave a 3/4 X 1 X 3-1/4 inch wooden block available.

WOODEN BLOCK

LENGTH

WIDTH

1.00 IN.

3.25 IN.

 

HEIGHT

 

.75 IN.

 

6

5 4

1Upper Pulley

2Drive Belt

3Lower Pulley Fixed Face

4Lower Pulley Spread Apart

5Lower Pulley Movable Face

6Squeeze and Pull Up To Spread Lower Pulley

3

Figure 16. Wooden Block For Spacer

Figure 18. Expanding Lower Drive Pulley

HTN- SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 29

Image 29
Contents Model HTN-27K-TCSL Model HTN-28K-TCSL Page Silicosis Warning Table of Contents Order via Fax Dealers Only Best Deal! Order via Internet Dealers OnlyMachine layout, location of components, checking of engine Training ChecklistTraining Checklist Daily PRE-OPERATION Checklist Daily PRE-OPERATION ChecklistYou can be Injured if you do not follow these directions HTN-SERIES Safety Message Alert SymbolsAlways wear approved eye and hearing protection Always wear approved respiratory protectionDo not operate or service this equipment SafetyRules for Safe Operation Fatigue, illness or taking medicineLifting the Ride-On Trowel Always keep the work area well organizedBattery Towing Safety PrecautionsHTN-SERIES Rules for Safe Operation TransportingAlways know the location of the nearest first aid kit Maintenance SafetyEmergencies Machine Safety Decals HTN-SERIES Operation and Safety DecalsHTN-SERIES- Specifications Trowel HTN-Series Engine Specifications HTN-SERIES- Specifications EngineEngine Blades HTN Series Ride-On PowerTrowel FamiliarizationHTN-SERIES General Information HTN-SERIES Controls and Indicators HTN-SERIES Controls and Indicators Initial Servicing HTN-SERIES Basic EngineKohler 28 HP Engine Kohler 27 HP Engine Control Handle Assembly Trowel Pre-Set Up InstructionsSeat Assembly Battery SetupGearbox Oil Level HTN-SERIES Initial START-UPEngine Oil Level Always check engine oil Before Each USE Fuel Gauge Important Information Before You Start HTN-SERIES OperationSteering HTN-SERIES OperationMaintenance Schedule HTN-SERIES MaintenanceReinstall the air cleaner cover and secure the latches HTN-SERIES MaintenanceAir Cleaner Daily Disassembly and Reassembly Standard Type Air Cleaner Components to CheckMake sure the cooling shrouds are reinstalled Make sure the correct depth airOil Filter 100 Hours Changing Engine Oil And FilterFuel Filter 200 Hours Oil And Fuel LinesHave a 3/4 X 1 X 3-1/4 inch wooden block available Checking The Drive BeltRemoving the Drive Belt Reinstall the spare belt carrier and the drive belt guard HTN-SERIES- MaintenanceInstalling the Drive Belt Using Replacement Drive Belt Wooden BlockSpare Drive Belt Replacement HTN-SERIES- MaintenanceTorque Converter/Variable Pitch Pulley Drive Pulley Drive System Theory of OperationClutch How It Works Figure Condition a z Engine IdlingBlade Pitch Matching Blade Pitch for Both Sets of BladesStabilizer Ring Removal Trowel Arm adjustment ProcedureRemove the trowel arm from the spider plate Trowel Arm RemovalTrowel Blade Removal Spider Plate Hex Head Bolt Zerk FittingSideview Trowel Arm AdjustmentChecking Trowel Arm Straightness Re-Assembly Trowel Arm Adjustment SetupDecommissioning Trowel/Components Installing Pans Onto Finisher BladesSymptom Possible Problem Solution HTN-SERIES -TROUBLESHOOTING Engine HTN-SERIES-TROUBLESHOOTING Trowel Troubleshooting HTN-SERIES-TROUBLESHOOTING TrowelHTN-SERIES Notes Payment Terms Page Mexico United Kingdom United StatesCanada Brazil Your Local Dealer is

HTN-27K-TCSL specifications

The Multiquip HTN-27K-TCSL is a cutting-edge piece of technology designed for professionals in the construction and industrial sectors. This portable hydraulic power unit is known for its robust performance and versatility, making it an ideal choice for a wide range of applications.

One of the standout features of the HTN-27K-TCSL is its powerful engine. Equipped with a reliable 27-horsepower Kohler engine, this unit ensures maximum efficiency and performance, allowing operators to complete tasks quickly and effectively. The engine is designed to be both fuel-efficient and environmentally friendly, adhering to emission regulations without sacrificing power.

The HTN-27K-TCSL boasts a unique hydraulic system that delivers high-pressure flow rates, making it suitable for operating multiple tools simultaneously. With a maximum hydraulic pressure of 3,000 PSI, this power unit can effortlessly handle demanding tasks such as concrete breaking, water jetting, and other heavy-duty applications. The ability to provide consistent hydraulic power allows for enhanced productivity on job sites.

In terms of versatility, the Multiquip HTN-27K-TCSL is equipped with a wide range of output options. Its hydraulic outlet configurations can support various attachments, enabling users to adapt the unit for diverse tasks. This flexibility makes it an invaluable tool for contractors, landscapers, and utility companies.

Another notable characteristic of the HTN-27K-TCSL is its rugged construction. Built to withstand the rigors of tough job sites, this hydraulic power unit features a durable frame and protective covers that shield the engine and components from dust and debris. The compact design ensures easy transportation and maneuverability, making it a practical choice for both indoor and outdoor use.

Additionally, the HTN-27K-TCSL is designed with operator safety in mind. It features a user-friendly interface, with clearly labeled controls for easy operation. Safety features such as emergency shut-off switches and protective guards further enhance its usability, ensuring that operators can work confidently.

In summary, the Multiquip HTN-27K-TCSL is a powerful, versatile, and robust hydraulic power unit designed to meet the demanding needs of various industries. With its exceptional performance, durable construction, and focus on safety, it continues to be a trusted choice among professionals seeking reliable hydraulic solutions.