Multiquip HTN-27K-TCSL Trowel Pre-Set Up Instructions, Control Handle Assembly, Seat Assembly

Page 21

HTN-SERIES — NEW MACHINE SETUP INSTRUCTIONS

Trowel Pre-Set Up Instructions

The purpose of this section is to assist the user in setting up a NEW trowel. If your trowel is already assembled, (seat, handles, knobs and battery), this section can be skipped.

The new trowel cannot be put into service until the pre-setup installation instructions are completed. These

NOTE pre-setup instructions only need to be performed at the time of unpacking a NEW trowel.

Before packaging and shipping, this HTN SERIES Ride-On Power Trowel was run and tested at the factory. If there are problems, please let us know.

Control Handle Assembly

The steering control handles are not attached to the trowel's two lower handles at the time of shipment. To attach the steering control handles to the two lower handle assemblies perform the following:

1.Remove the bolts from the plastic bag tied to the control towers.

2.Remove all protective wrapping and straps from the control handles.

3.Slip the top (loose) piece into the base of the corresponding handle, making sure to line up the holes.

4.Install the bolt through the lined up holes and tighten the acorn nut onto the threaded end.

Seat Assembly

The seat is not installed on the trowel for shipping purposes. To attach the seat perform the following:

There are two types of seats,

NOTE

depending on what type of trowel

 

 

you have. J and B series trowels have

slots on the seat mounting plate that allow fore and aft adjustment of the seat. H-series trowels have a seat that is mounted on tracks,

similar to an automobile seat. This seat can be adjusted fore and aft via the control lever under the front of the seat.

1.Remove the seat from the protective wrapping.

2.Remove the bolts on the bottom of the seat, and place seat on the seat mounting plate, then insert the bolts through the holes or slots on the seat mounting plate and tighten.

Battery Setup

This trowel was shipped with a wet charged battery.This battery may need to be charged for a brief period of time as per the manufacturer instructions.

CAUTION

Use all safety precautions specified by the battery manufacturer when working with the battery. See further specific safety information on page 12 of this manual.

Some models are equipped with

To install the battery on the trowel, make sure that the battery is well seated in the battery box.. Connect the positive cable to the

NOTE

adjustable height handles. Adjust the height by placing the bolt through the set of holes that corresponds to the most comfortable height.

positive terminal on the battery first, then connect the negative cable to the negative terminal. Close the plastic battery box cover and secure the battery box.

5.Pay close attention to any wires that may be inside the control handles. DO NOT pinch or cut any wires during installation.

6.Inside the plastic bag of parts are two knobs for the pitch control tower cranks. Install these two knobs onto the tower crank levers.

HTN- SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Model HTN-27K-TCSL Model HTN-28K-TCSL Page Silicosis Warning Table of Contents Order via Fax Dealers Only Best Deal! Order via Internet Dealers OnlyTraining Checklist Training ChecklistMachine layout, location of components, checking of engine Daily PRE-OPERATION Checklist Daily PRE-OPERATION ChecklistYou can be Injured if you do not follow these directions HTN-SERIES Safety Message Alert SymbolsAlways wear approved eye and hearing protection Always wear approved respiratory protectionDo not operate or service this equipment SafetyRules for Safe Operation Fatigue, illness or taking medicineLifting the Ride-On Trowel Always keep the work area well organizedBattery Towing Safety PrecautionsHTN-SERIES Rules for Safe Operation TransportingMaintenance Safety EmergenciesAlways know the location of the nearest first aid kit Machine Safety Decals HTN-SERIES Operation and Safety DecalsHTN-SERIES- Specifications Trowel HTN-Series Engine Specifications HTN-SERIES- Specifications EngineHTN Series Ride-On PowerTrowel Familiarization HTN-SERIES General InformationEngine Blades HTN-SERIES Controls and Indicators HTN-SERIES Controls and Indicators HTN-SERIES Basic Engine Kohler 28 HP Engine Kohler 27 HP EngineInitial Servicing Control Handle Assembly Trowel Pre-Set Up InstructionsSeat Assembly Battery SetupHTN-SERIES Initial START-UP Engine Oil Level Always check engine oil Before Each USEGearbox Oil Level Fuel Gauge Important Information Before You Start HTN-SERIES OperationSteering HTN-SERIES OperationMaintenance Schedule HTN-SERIES MaintenanceHTN-SERIES Maintenance Air Cleaner DailyReinstall the air cleaner cover and secure the latches Disassembly and Reassembly Standard Type Air Cleaner Components to CheckMake sure the cooling shrouds are reinstalled Make sure the correct depth airOil Filter 100 Hours Changing Engine Oil And FilterFuel Filter 200 Hours Oil And Fuel LinesChecking The Drive Belt Removing the Drive BeltHave a 3/4 X 1 X 3-1/4 inch wooden block available Reinstall the spare belt carrier and the drive belt guard HTN-SERIES- MaintenanceInstalling the Drive Belt Using Replacement Drive Belt Wooden BlockSpare Drive Belt Replacement HTN-SERIES- MaintenanceTorque Converter/Variable Pitch Pulley Drive Pulley Drive System Theory of OperationClutch How It Works Figure Condition a z Engine IdlingBlade Pitch Matching Blade Pitch for Both Sets of BladesStabilizer Ring Removal Trowel Arm adjustment ProcedureRemove the trowel arm from the spider plate Trowel Arm RemovalTrowel Blade Removal Spider Plate Hex Head Bolt Zerk FittingTrowel Arm Adjustment Checking Trowel Arm StraightnessSideview Re-Assembly Trowel Arm Adjustment SetupDecommissioning Trowel/Components Installing Pans Onto Finisher BladesSymptom Possible Problem Solution HTN-SERIES -TROUBLESHOOTING Engine HTN-SERIES-TROUBLESHOOTING Trowel Troubleshooting HTN-SERIES-TROUBLESHOOTING TrowelHTN-SERIES Notes Payment Terms Page Mexico United Kingdom United StatesCanada Brazil Your Local Dealer is

HTN-27K-TCSL specifications

The Multiquip HTN-27K-TCSL is a cutting-edge piece of technology designed for professionals in the construction and industrial sectors. This portable hydraulic power unit is known for its robust performance and versatility, making it an ideal choice for a wide range of applications.

One of the standout features of the HTN-27K-TCSL is its powerful engine. Equipped with a reliable 27-horsepower Kohler engine, this unit ensures maximum efficiency and performance, allowing operators to complete tasks quickly and effectively. The engine is designed to be both fuel-efficient and environmentally friendly, adhering to emission regulations without sacrificing power.

The HTN-27K-TCSL boasts a unique hydraulic system that delivers high-pressure flow rates, making it suitable for operating multiple tools simultaneously. With a maximum hydraulic pressure of 3,000 PSI, this power unit can effortlessly handle demanding tasks such as concrete breaking, water jetting, and other heavy-duty applications. The ability to provide consistent hydraulic power allows for enhanced productivity on job sites.

In terms of versatility, the Multiquip HTN-27K-TCSL is equipped with a wide range of output options. Its hydraulic outlet configurations can support various attachments, enabling users to adapt the unit for diverse tasks. This flexibility makes it an invaluable tool for contractors, landscapers, and utility companies.

Another notable characteristic of the HTN-27K-TCSL is its rugged construction. Built to withstand the rigors of tough job sites, this hydraulic power unit features a durable frame and protective covers that shield the engine and components from dust and debris. The compact design ensures easy transportation and maneuverability, making it a practical choice for both indoor and outdoor use.

Additionally, the HTN-27K-TCSL is designed with operator safety in mind. It features a user-friendly interface, with clearly labeled controls for easy operation. Safety features such as emergency shut-off switches and protective guards further enhance its usability, ensuring that operators can work confidently.

In summary, the Multiquip HTN-27K-TCSL is a powerful, versatile, and robust hydraulic power unit designed to meet the demanding needs of various industries. With its exceptional performance, durable construction, and focus on safety, it continues to be a trusted choice among professionals seeking reliable hydraulic solutions.
Top Page Image Contents