Multiquip HTN-27K-TCSL Installing Pans Onto Finisher Blades, Decommissioning Trowel/Components

Page 38

Installing Pans Onto Finisher Blades

These rounddiscssometimesreferredto as"pans" attachtothe spiders arms and allow early floating on wet concrete and easy movement from wet to dry areas.They are also very effective in embedding large aggregates and surface hardeners.

WARNING

ALWAYS install pans either on the work area or on an area that is next to and level with the work area. DO NOT lift the trowel when the pans are attached.

Refer to Figure 40 when installing pans onto finisher blades.

2

3

1

4

HTN-SERIES — MAINTENANCE

1.Lift trowel just enough to slide pan under blades. Lower finisher onto pan with blades (item #1) adjacent to Z-Clips (item #4).

2.Rotate blades into position under Z-Clips. Ensure that the bladesarerotatedinthedirectionoftravelwhenthemachine is in operation or use the engine to rotate the blades into position.

3.Attach the blade tie-downs (item #3) to the far side of the Z- Clip brackets (item #4) with tie-down knobs (item #2) as shown in figure 40.

4.Check to make certain that the blade edges are secured undertheZ-Clipsandthetie-downsaresecuredcompletely overtheedgesofthebladebarbeforethemachineisputback intooperation.

Decommissioning Trowel/Components

Decommissioning is a controlled process used to safely retire a pieceofequipmentthatisnolongerserviceable. Iftheequipment poses an unacceptable and unrepairable safety risk due to wear or damage or is no longer cost effective to maintain, (beyond life- cycle reliability) and is to be decommissioned, (demolition and dismantlement), the following procedure must take place:

1.Drain all fluids completely. These may include oil, gasoline, hydraulic oil and antifreeze. Dispose of properly in accor- dance with local and governmental regulations. Never pour on ground or dump down drains or sewers.

2.Remove battery and bring to appropriate facility for lead reclamation. Use safety precautions when handling batter- ies that contain sulfuric acid, (See page 12).

3.The remainder can be brought to a salvage yard or metal reclamation facility for further dismantling.

1BLADE ASSEMBLY

2KNOB, TIE-DOWN Z-CLIP PANS

3TIE-DOWN, BLADE

4Z-CLIP, PAN

Figure 40. Z-Clip Finisher Pan Installation

HTN-SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 38

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Model HTN-27K-TCSL Model HTN-28K-TCSL Page Silicosis Warning Table of Contents Best Deal! Order via Internet Dealers Only Order via Fax Dealers OnlyMachine layout, location of components, checking of engine Training ChecklistTraining Checklist Daily PRE-OPERATION Checklist Daily PRE-OPERATION ChecklistHTN-SERIES Safety Message Alert Symbols You can be Injured if you do not follow these directionsAlways wear approved respiratory protection Always wear approved eye and hearing protectionRules for Safe Operation SafetyDo not operate or service this equipment Fatigue, illness or taking medicineAlways keep the work area well organized Lifting the Ride-On TrowelHTN-SERIES Rules for Safe Operation Towing Safety PrecautionsBattery TransportingAlways know the location of the nearest first aid kit Maintenance SafetyEmergencies HTN-SERIES Operation and Safety Decals Machine Safety DecalsHTN-SERIES- Specifications Trowel HTN-SERIES- Specifications Engine HTN-Series Engine SpecificationsEngine Blades HTN Series Ride-On PowerTrowel FamiliarizationHTN-SERIES General Information HTN-SERIES Controls and Indicators HTN-SERIES Controls and Indicators Initial Servicing HTN-SERIES Basic EngineKohler 28 HP Engine Kohler 27 HP Engine Seat Assembly Trowel Pre-Set Up InstructionsControl Handle Assembly Battery SetupGearbox Oil Level HTN-SERIES Initial START-UPEngine Oil Level Always check engine oil Before Each USE HTN-SERIES Operation Fuel Gauge Important Information Before You StartHTN-SERIES Operation SteeringHTN-SERIES Maintenance Maintenance ScheduleReinstall the air cleaner cover and secure the latches HTN-SERIES MaintenanceAir Cleaner Daily Make sure the cooling shrouds are reinstalled Air Cleaner Components to CheckDisassembly and Reassembly Standard Type Make sure the correct depth airFuel Filter 200 Hours Changing Engine Oil And FilterOil Filter 100 Hours Oil And Fuel LinesHave a 3/4 X 1 X 3-1/4 inch wooden block available Checking The Drive BeltRemoving the Drive Belt Installing the Drive Belt Using Replacement Drive Belt HTN-SERIES- MaintenanceReinstall the spare belt carrier and the drive belt guard Wooden BlockHTN-SERIES- Maintenance Spare Drive Belt ReplacementDrive System Theory of Operation Torque Converter/Variable Pitch Pulley Drive PulleyBlade Pitch How It Works Figure Condition a z Engine IdlingClutch Matching Blade Pitch for Both Sets of BladesTrowel Arm adjustment Procedure Stabilizer Ring RemovalTrowel Blade Removal Trowel Arm RemovalRemove the trowel arm from the spider plate Spider Plate Hex Head Bolt Zerk FittingSideview Trowel Arm AdjustmentChecking Trowel Arm Straightness Trowel Arm Adjustment Setup Re-AssemblyInstalling Pans Onto Finisher Blades Decommissioning Trowel/ComponentsSymptom Possible Problem Solution HTN-SERIES -TROUBLESHOOTING Engine HTN-SERIES-TROUBLESHOOTING Trowel HTN-SERIES-TROUBLESHOOTING Trowel TroubleshootingHTN-SERIES Notes Payment Terms Page Canada Brazil United StatesMexico United Kingdom Your Local Dealer is

HTN-27K-TCSL specifications

The Multiquip HTN-27K-TCSL is a cutting-edge piece of technology designed for professionals in the construction and industrial sectors. This portable hydraulic power unit is known for its robust performance and versatility, making it an ideal choice for a wide range of applications.

One of the standout features of the HTN-27K-TCSL is its powerful engine. Equipped with a reliable 27-horsepower Kohler engine, this unit ensures maximum efficiency and performance, allowing operators to complete tasks quickly and effectively. The engine is designed to be both fuel-efficient and environmentally friendly, adhering to emission regulations without sacrificing power.

The HTN-27K-TCSL boasts a unique hydraulic system that delivers high-pressure flow rates, making it suitable for operating multiple tools simultaneously. With a maximum hydraulic pressure of 3,000 PSI, this power unit can effortlessly handle demanding tasks such as concrete breaking, water jetting, and other heavy-duty applications. The ability to provide consistent hydraulic power allows for enhanced productivity on job sites.

In terms of versatility, the Multiquip HTN-27K-TCSL is equipped with a wide range of output options. Its hydraulic outlet configurations can support various attachments, enabling users to adapt the unit for diverse tasks. This flexibility makes it an invaluable tool for contractors, landscapers, and utility companies.

Another notable characteristic of the HTN-27K-TCSL is its rugged construction. Built to withstand the rigors of tough job sites, this hydraulic power unit features a durable frame and protective covers that shield the engine and components from dust and debris. The compact design ensures easy transportation and maneuverability, making it a practical choice for both indoor and outdoor use.

Additionally, the HTN-27K-TCSL is designed with operator safety in mind. It features a user-friendly interface, with clearly labeled controls for easy operation. Safety features such as emergency shut-off switches and protective guards further enhance its usability, ensuring that operators can work confidently.

In summary, the Multiquip HTN-27K-TCSL is a powerful, versatile, and robust hydraulic power unit designed to meet the demanding needs of various industries. With its exceptional performance, durable construction, and focus on safety, it continues to be a trusted choice among professionals seeking reliable hydraulic solutions.
Top Page Image Contents