Multiquip HTN-27K-TCSL operation manual HTN-SERIES- Maintenance, Wooden Block

Page 30

HTN-SERIES— MAINTENANCE

3.Insert the 3/4" X 1" X 3-1/4" block between the moveable face and the fixed face of the lower drive pulley. See Figure 19. This block will help keep the lower drive pulley faces open while installing the new drive belt.

1

Wooden Block

Figure 19. Holding Lower Pulley Open

4.If the belt is not being reused (recommended), CUT the drive belt. Ensure all belt remnants are removed from the pulleys.

In the event of a drive belt failure, the spare (replacement) drive belt can be used for quick replacement at the job site to continue trowel operation.

1.If necessary, refer to Removing Drive Belt Instructions. Ensure all remnants of old belt have been removed from pulleys.

2.To replace the drive belt with the spare drive belt, remove the 2 bolts that secure the drive belt carrier. (Figure 20) This will allow free movement of the belt for installation. Take care with to not contaminate the relplacement belt with grease or dirt.

3.With the 3/4 x 1 x 3-1/4 wood block holding the lower pulley open, place the replacement belt into the lower pulley first. Work the belt over the upper drive pulley into the pulley groove.

4.Squeeze the belt enough to remove the wood block. With the block removed, release the tension on the belt.

5.Reinstall the spare belt carrier and the drive belt guard.

6.Replace the spare belt before the next trowel use. See spare drive belt replacement procedures.

Installing the Drive Belt (Using Replacement Drive Belt)

The HTN-SERIES Ride-On Power Trowel is equipped with a replacement drive belt (spare) carrier, which is mounted on the inboard side of the fuel tank near the clutch. Make sure that there is ALWAYS a spare drive belt in the drive belt carrier before the trowel is placed on a slab to finish concrete.

2

1

4 5

6

Figure 20. Drive Belt Install

3

1Bolt, Spare Drive Belt Carrier

2Spare Drive Belt Holder

3Wooden Block

4CV-Joint

5New Spare Drive Belt

6Lower Drive Pulley

HTN-SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Model HTN-27K-TCSL Model HTN-28K-TCSL Page Silicosis Warning Table of Contents Best Deal! Order via Internet Dealers Only Order via Fax Dealers OnlyTraining Checklist Training ChecklistMachine layout, location of components, checking of engine Daily PRE-OPERATION Checklist Daily PRE-OPERATION ChecklistHTN-SERIES Safety Message Alert Symbols You can be Injured if you do not follow these directionsAlways wear approved respiratory protection Always wear approved eye and hearing protectionRules for Safe Operation SafetyDo not operate or service this equipment Fatigue, illness or taking medicineAlways keep the work area well organized Lifting the Ride-On TrowelHTN-SERIES Rules for Safe Operation Towing Safety PrecautionsBattery TransportingMaintenance Safety EmergenciesAlways know the location of the nearest first aid kit HTN-SERIES Operation and Safety Decals Machine Safety DecalsHTN-SERIES- Specifications Trowel HTN-SERIES- Specifications Engine HTN-Series Engine SpecificationsHTN Series Ride-On PowerTrowel Familiarization HTN-SERIES General InformationEngine Blades HTN-SERIES Controls and Indicators HTN-SERIES Controls and Indicators HTN-SERIES Basic Engine Kohler 28 HP Engine Kohler 27 HP EngineInitial Servicing Seat Assembly Trowel Pre-Set Up InstructionsControl Handle Assembly Battery SetupHTN-SERIES Initial START-UP Engine Oil Level Always check engine oil Before Each USEGearbox Oil Level HTN-SERIES Operation Fuel Gauge Important Information Before You StartHTN-SERIES Operation SteeringHTN-SERIES Maintenance Maintenance ScheduleHTN-SERIES Maintenance Air Cleaner DailyReinstall the air cleaner cover and secure the latches Make sure the cooling shrouds are reinstalled Air Cleaner Components to CheckDisassembly and Reassembly Standard Type Make sure the correct depth airFuel Filter 200 Hours Changing Engine Oil And FilterOil Filter 100 Hours Oil And Fuel LinesChecking The Drive Belt Removing the Drive BeltHave a 3/4 X 1 X 3-1/4 inch wooden block available Installing the Drive Belt Using Replacement Drive Belt HTN-SERIES- MaintenanceReinstall the spare belt carrier and the drive belt guard Wooden BlockHTN-SERIES- Maintenance Spare Drive Belt ReplacementDrive System Theory of Operation Torque Converter/Variable Pitch Pulley Drive PulleyBlade Pitch How It Works Figure Condition a z Engine IdlingClutch Matching Blade Pitch for Both Sets of BladesTrowel Arm adjustment Procedure Stabilizer Ring RemovalTrowel Blade Removal Trowel Arm RemovalRemove the trowel arm from the spider plate Spider Plate Hex Head Bolt Zerk FittingTrowel Arm Adjustment Checking Trowel Arm StraightnessSideview Trowel Arm Adjustment Setup Re-AssemblyInstalling Pans Onto Finisher Blades Decommissioning Trowel/ComponentsSymptom Possible Problem Solution HTN-SERIES -TROUBLESHOOTING Engine HTN-SERIES-TROUBLESHOOTING Trowel HTN-SERIES-TROUBLESHOOTING Trowel TroubleshootingHTN-SERIES Notes Payment Terms Page Canada Brazil United StatesMexico United Kingdom Your Local Dealer is

HTN-27K-TCSL specifications

The Multiquip HTN-27K-TCSL is a cutting-edge piece of technology designed for professionals in the construction and industrial sectors. This portable hydraulic power unit is known for its robust performance and versatility, making it an ideal choice for a wide range of applications.

One of the standout features of the HTN-27K-TCSL is its powerful engine. Equipped with a reliable 27-horsepower Kohler engine, this unit ensures maximum efficiency and performance, allowing operators to complete tasks quickly and effectively. The engine is designed to be both fuel-efficient and environmentally friendly, adhering to emission regulations without sacrificing power.

The HTN-27K-TCSL boasts a unique hydraulic system that delivers high-pressure flow rates, making it suitable for operating multiple tools simultaneously. With a maximum hydraulic pressure of 3,000 PSI, this power unit can effortlessly handle demanding tasks such as concrete breaking, water jetting, and other heavy-duty applications. The ability to provide consistent hydraulic power allows for enhanced productivity on job sites.

In terms of versatility, the Multiquip HTN-27K-TCSL is equipped with a wide range of output options. Its hydraulic outlet configurations can support various attachments, enabling users to adapt the unit for diverse tasks. This flexibility makes it an invaluable tool for contractors, landscapers, and utility companies.

Another notable characteristic of the HTN-27K-TCSL is its rugged construction. Built to withstand the rigors of tough job sites, this hydraulic power unit features a durable frame and protective covers that shield the engine and components from dust and debris. The compact design ensures easy transportation and maneuverability, making it a practical choice for both indoor and outdoor use.

Additionally, the HTN-27K-TCSL is designed with operator safety in mind. It features a user-friendly interface, with clearly labeled controls for easy operation. Safety features such as emergency shut-off switches and protective guards further enhance its usability, ensuring that operators can work confidently.

In summary, the Multiquip HTN-27K-TCSL is a powerful, versatile, and robust hydraulic power unit designed to meet the demanding needs of various industries. With its exceptional performance, durable construction, and focus on safety, it continues to be a trusted choice among professionals seeking reliable hydraulic solutions.
Top Page Image Contents