Multiquip HTN-27K-TCSL operation manual HTN-SERIES- Maintenance, Spare Drive Belt Replacement

Page 31

HTN-SERIES— MAINTENANCE

5

6

4

2 1

3

1CV Joint

2Bolt (Remove 3 places)

3New Spare Drive Belt

4Bolt, Spare Drive Belt Carrier

5Spare Drive Belt Holder

6Left Side Gearbox

Figure 21. Spare Drive Belt Replacement

Spare Drive Belt Replacement

It will be necessary to disconnect the CV-Joint from the left-side gearbox

NOTE coupler.This means the removal of the three screws that secure the CV- Joint to the gearbox.

To replace a spare drive belt, be prepared to disconnect the CV- joint from the left-side gearbox. See Figure 21.

1.Place the trowel on suitable supports and observe all safety precautions.

2.Remove the three screws that secure the CV-joint to the left-side gearbox coupler.

3.Once the CV-joint has been separated from the left-side gearbox, push the CV-joint inward so that a gap exists between the gearbox and the CV-joint (Figure 21). Slide the spare V-belt between the gearbox coupler and the CV- joint. Avoid contaminating the replacement belt with grease or oil when sliding it between the CV-Joint and gearbox coupler.

4.Place the spare drive belt inside the drive belt carrier, and secure the spare belt carrier to the inboard side of the left gearbox.

5.Install the three screws that secure the CV-joint to the left- side gearbox coupler.

HTN- SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 31

Image 31

Contents

Model HTN-27K-TCSL Model HTN-28K-TCSL Page Silicosis Warning Table of Contents Order via Fax Dealers Only Best Deal! Order via Internet Dealers OnlyTraining Checklist Training ChecklistMachine layout, location of components, checking of engine Daily PRE-OPERATION Checklist Daily PRE-OPERATION ChecklistYou can be Injured if you do not follow these directions HTN-SERIES Safety Message Alert SymbolsAlways wear approved eye and hearing protection Always wear approved respiratory protectionFatigue, illness or taking medicine SafetyDo not operate or service this equipment Rules for Safe OperationLifting the Ride-On Trowel Always keep the work area well organizedTransporting Towing Safety PrecautionsBattery HTN-SERIES Rules for Safe OperationEmergencies Maintenance SafetyAlways know the location of the nearest first aid kit Machine Safety Decals HTN-SERIES Operation and Safety DecalsHTN-SERIES- Specifications Trowel HTN-Series Engine Specifications HTN-SERIES- Specifications EngineHTN-SERIES General Information HTN Series Ride-On PowerTrowel FamiliarizationEngine Blades HTN-SERIES Controls and Indicators HTN-SERIES Controls and Indicators Kohler 28 HP Engine Kohler 27 HP Engine HTN-SERIES Basic EngineInitial Servicing Battery Setup Trowel Pre-Set Up InstructionsControl Handle Assembly Seat AssemblyEngine Oil Level Always check engine oil Before Each USE HTN-SERIES Initial START-UPGearbox Oil Level Fuel Gauge Important Information Before You Start HTN-SERIES OperationSteering HTN-SERIES OperationMaintenance Schedule HTN-SERIES MaintenanceAir Cleaner Daily HTN-SERIES MaintenanceReinstall the air cleaner cover and secure the latches Make sure the correct depth air Air Cleaner Components to Check Disassembly and Reassembly Standard Type Make sure the cooling shrouds are reinstalledOil And Fuel Lines Changing Engine Oil And FilterOil Filter 100 Hours Fuel Filter 200 HoursRemoving the Drive Belt Checking The Drive BeltHave a 3/4 X 1 X 3-1/4 inch wooden block available Wooden Block HTN-SERIES- MaintenanceReinstall the spare belt carrier and the drive belt guard Installing the Drive Belt Using Replacement Drive BeltSpare Drive Belt Replacement HTN-SERIES- MaintenanceTorque Converter/Variable Pitch Pulley Drive Pulley Drive System Theory of OperationMatching Blade Pitch for Both Sets of Blades How It Works Figure Condition a z Engine IdlingClutch Blade PitchStabilizer Ring Removal Trowel Arm adjustment ProcedureSpider Plate Hex Head Bolt Zerk Fitting Trowel Arm RemovalRemove the trowel arm from the spider plate Trowel Blade RemovalChecking Trowel Arm Straightness Trowel Arm AdjustmentSideview Re-Assembly Trowel Arm Adjustment SetupDecommissioning Trowel/Components Installing Pans Onto Finisher BladesSymptom Possible Problem Solution HTN-SERIES -TROUBLESHOOTING Engine HTN-SERIES-TROUBLESHOOTING Trowel Troubleshooting HTN-SERIES-TROUBLESHOOTING TrowelHTN-SERIES Notes Payment Terms Page Your Local Dealer is United StatesMexico United Kingdom Canada Brazil