Multiquip HTN-27K-TCSL Always keep the work area well organized, Lifting the Ride-On Trowel

Page 11

HTN-SERIES — RULES FOR SAFE OPERATION

■NEVER run engine without air filter. Severe engine damage may occur. Service air filter frequently to prevent carburetor malfunction.

■NEVER place your feet or hands inside the guard rings while starting or operating this equipment.

■AVOID wearing jewelry or loose fitting clothing that may snag on the controls or moving parts as this can cause a serious injury.

■ALWAYS keep clear of rotating or moving parts while operating the trowel.

■Moving Parts – Shut down the engine before performing service or maintenance functions. Contact with moving parts can cause serious injury.

■ALWAYS check to make sure that the operating area is clear before starting the engine.

■NEVER leave the machine unattended while running.

■ALWAYS be sure the operator is familiar with proper safety precautions and operations techniques before using trowel.

■ALWAYS keep the work area well organized.

■ALWAYS clear the work area of any debris, tools, etc. that would constitute a hazard while the trowel is in operation.

WARNING

ALWAYS check to make sure that the operating area is clear before starting the engine.

■No one other than the operator is to be in the working area when the trowel is in operation.

■NEVER allow passengers or riders on the trowel during operation.

■Always observe all applicable compulsory regulations relevant to environmental protection, especially, fuel storage, the handling of hazardous substances, and the wearing of protective clothing and equipment. Instruct the user as necessary, or, as the user, request this information and training.

■ALWAYS store equipment properly when it is not being used. Equipment should be stored in a clean, dry location out of the reach of children.

DANGER

Pay close attention to ventilation when operating the trowel in confined spaces such as tunnels, buildings or similar areas. The engine exhaust contains harmful elements. Ensure proper air flow to move engine exhaust away from the operator.

Lifting the Ride-On Trowel

CAUTION

This ride-on trowel is very heavy and awkward to move around. Use proper heavy lifting procedures and DO NOT attempt to lift the ride-on trowel by the guard rings.

The HTN-Series Ride-On PowerTrowel is designed to be moved and handled several ways.

The easiest way to lift the trowel is to utilize the lift loops that are welded to the frame.These lift loops are located to the left and right sides of the operator’s seat.

A strap or chain can be attached to these lift loops, allowing a forklift or crane to lift the trowel up onto and off of a slab of concrete. The strap or chain should have a minimum 2,000 pounds (1000- kg) lifting capacity and the lifting gear must be capable of lifting at least this amount.

DANGER

NEVERstand under or allow anyone else to stand under the trowel while it is being lifted.

HTN- SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Model HTN-27K-TCSL Model HTN-28K-TCSL Page Silicosis Warning Table of Contents Order via Fax Dealers Only Best Deal! Order via Internet Dealers OnlyMachine layout, location of components, checking of engine Training ChecklistTraining Checklist Daily PRE-OPERATION Checklist Daily PRE-OPERATION ChecklistYou can be Injured if you do not follow these directions HTN-SERIES Safety Message Alert SymbolsAlways wear approved eye and hearing protection Always wear approved respiratory protectionFatigue, illness or taking medicine SafetyDo not operate or service this equipment Rules for Safe OperationLifting the Ride-On Trowel Always keep the work area well organizedTransporting Towing Safety PrecautionsBattery HTN-SERIES Rules for Safe OperationAlways know the location of the nearest first aid kit Maintenance SafetyEmergencies Machine Safety Decals HTN-SERIES Operation and Safety DecalsHTN-SERIES- Specifications Trowel HTN-Series Engine Specifications HTN-SERIES- Specifications EngineEngine Blades HTN Series Ride-On PowerTrowel FamiliarizationHTN-SERIES General Information HTN-SERIES Controls and Indicators HTN-SERIES Controls and Indicators Initial Servicing HTN-SERIES Basic EngineKohler 28 HP Engine Kohler 27 HP Engine Battery Setup Trowel Pre-Set Up InstructionsControl Handle Assembly Seat AssemblyGearbox Oil Level HTN-SERIES Initial START-UPEngine Oil Level Always check engine oil Before Each USE Fuel Gauge Important Information Before You Start HTN-SERIES OperationSteering HTN-SERIES OperationMaintenance Schedule HTN-SERIES MaintenanceReinstall the air cleaner cover and secure the latches HTN-SERIES MaintenanceAir Cleaner Daily Make sure the correct depth air Air Cleaner Components to CheckDisassembly and Reassembly Standard Type Make sure the cooling shrouds are reinstalledOil And Fuel Lines Changing Engine Oil And FilterOil Filter 100 Hours Fuel Filter 200 HoursHave a 3/4 X 1 X 3-1/4 inch wooden block available Checking The Drive BeltRemoving the Drive Belt Wooden Block HTN-SERIES- MaintenanceReinstall the spare belt carrier and the drive belt guard Installing the Drive Belt Using Replacement Drive BeltSpare Drive Belt Replacement HTN-SERIES- MaintenanceTorque Converter/Variable Pitch Pulley Drive Pulley Drive System Theory of OperationMatching Blade Pitch for Both Sets of Blades How It Works Figure Condition a z Engine IdlingClutch Blade PitchStabilizer Ring Removal Trowel Arm adjustment ProcedureSpider Plate Hex Head Bolt Zerk Fitting Trowel Arm RemovalRemove the trowel arm from the spider plate Trowel Blade RemovalSideview Trowel Arm AdjustmentChecking Trowel Arm Straightness Re-Assembly Trowel Arm Adjustment SetupDecommissioning Trowel/Components Installing Pans Onto Finisher BladesSymptom Possible Problem Solution HTN-SERIES -TROUBLESHOOTING Engine HTN-SERIES-TROUBLESHOOTING Trowel Troubleshooting HTN-SERIES-TROUBLESHOOTING TrowelHTN-SERIES Notes Payment Terms Page Your Local Dealer is United StatesMexico United Kingdom Canada Brazil

HTN-27K-TCSL specifications

The Multiquip HTN-27K-TCSL is a cutting-edge piece of technology designed for professionals in the construction and industrial sectors. This portable hydraulic power unit is known for its robust performance and versatility, making it an ideal choice for a wide range of applications.

One of the standout features of the HTN-27K-TCSL is its powerful engine. Equipped with a reliable 27-horsepower Kohler engine, this unit ensures maximum efficiency and performance, allowing operators to complete tasks quickly and effectively. The engine is designed to be both fuel-efficient and environmentally friendly, adhering to emission regulations without sacrificing power.

The HTN-27K-TCSL boasts a unique hydraulic system that delivers high-pressure flow rates, making it suitable for operating multiple tools simultaneously. With a maximum hydraulic pressure of 3,000 PSI, this power unit can effortlessly handle demanding tasks such as concrete breaking, water jetting, and other heavy-duty applications. The ability to provide consistent hydraulic power allows for enhanced productivity on job sites.

In terms of versatility, the Multiquip HTN-27K-TCSL is equipped with a wide range of output options. Its hydraulic outlet configurations can support various attachments, enabling users to adapt the unit for diverse tasks. This flexibility makes it an invaluable tool for contractors, landscapers, and utility companies.

Another notable characteristic of the HTN-27K-TCSL is its rugged construction. Built to withstand the rigors of tough job sites, this hydraulic power unit features a durable frame and protective covers that shield the engine and components from dust and debris. The compact design ensures easy transportation and maneuverability, making it a practical choice for both indoor and outdoor use.

Additionally, the HTN-27K-TCSL is designed with operator safety in mind. It features a user-friendly interface, with clearly labeled controls for easy operation. Safety features such as emergency shut-off switches and protective guards further enhance its usability, ensuring that operators can work confidently.

In summary, the Multiquip HTN-27K-TCSL is a powerful, versatile, and robust hydraulic power unit designed to meet the demanding needs of various industries. With its exceptional performance, durable construction, and focus on safety, it continues to be a trusted choice among professionals seeking reliable hydraulic solutions.
Top Page Image Contents