Multiquip HTN-27K-TCSL How It Works Figure Condition a z Engine Idling, Clutch, Blade Pitch

Page 33

How It Works (Figure 26)

Condition A: z Engine Idling

zDrive Pulley: Small

zDriven Pulley: Large

zBelt: Loose and Stationary

Condition B: z Engine Accelerating

zDrive Pulley: Small But Increasing

zDriven Pulley: Large But Decreasing

zBelt: Approaching Tightness

Condition C: z Engine At High Speed

zDrive Pulley: Large

zDriven Pulley: Small

zBelt: Tight

Clutch

This clutch system provides a high pulley ratio (a low gear- so to speak) to start out and a low pulley ratio (a high gear- so to speak) for a high speed operation, with infinite variation between the two.

This means that it will not be necessary to give full throttle in order to "break the blades/pans loose". The machine can slowly be brought up to speed.

The torque-sensitive pulley (Figure 27) utilizes a spring and cam. Peakperformanceresultsfromproperinteractionbetweenthedriven pulley spring and the ramp angle of the cam bracket.

SPRING

DRIVEN PULLEY

CAM

BRACKET

MOVEABLE

FIXED FACE

FACE

 

HTN-SERIES— MAINTENANCE

Blade Pitch

Sometimes it may be necessary to match blade pitch between the two sets of blades. There are some signs that this may be necessary. For example, the differences in pitch could cause a noticeable difference in finish quality between the two sets of blades.Or, the difference in blade pitch could make the machine difficult to control.This is due to the surface area in contact with the concrete (the blade set with the greater contact area tends to stick to the concrete more).

Matching Blade Pitch for Both Sets of Blades

Trowels equipped with Twin PitchTM Controls may need to have blade pitch between the two sets of blades "syncronized". If the blades need to be syncronized this is easily accomplished by performing the following. Refer to Figure 28.

1.Lift the pitch adjustment handle on either side. Once lifted, that side is now disconnected from the Twin PitchTM system.

2.Adjust to match the opposite side.

3.When adjusted, lower the handle to Twin PitchTM operating position.

A

B

 

 

 

TE

M

AN

 

 

HI

 

 

 

 

 

 

W

 

 

 

 

 

 

 

 

 

 

 

I E

S

 

 

R

 

 

 

E

 

 

 

S

 

 

 

 

 

 

 

 

 

Figure 27. Pulley Spring and Cam Bracket

A

Twin PitchTM disengaged (one side)

 

B

Operating Position

 

 

Figure 28. Pitch Towers

HTN- SERIES • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #0 (06/06/07) — PAGE 33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Model HTN-27K-TCSL Model HTN-28K-TCSL Page Silicosis Warning Table of Contents Order via Fax Dealers Only Best Deal! Order via Internet Dealers OnlyTraining Checklist Training ChecklistMachine layout, location of components, checking of engine Daily PRE-OPERATION Checklist Daily PRE-OPERATION ChecklistYou can be Injured if you do not follow these directions HTN-SERIES Safety Message Alert SymbolsAlways wear approved eye and hearing protection Always wear approved respiratory protectionDo not operate or service this equipment SafetyRules for Safe Operation Fatigue, illness or taking medicineLifting the Ride-On Trowel Always keep the work area well organizedBattery Towing Safety PrecautionsHTN-SERIES Rules for Safe Operation TransportingMaintenance Safety EmergenciesAlways know the location of the nearest first aid kit Machine Safety Decals HTN-SERIES Operation and Safety DecalsHTN-SERIES- Specifications Trowel HTN-Series Engine Specifications HTN-SERIES- Specifications EngineHTN Series Ride-On PowerTrowel Familiarization HTN-SERIES General InformationEngine Blades HTN-SERIES Controls and Indicators HTN-SERIES Controls and Indicators HTN-SERIES Basic Engine Kohler 28 HP Engine Kohler 27 HP EngineInitial Servicing Control Handle Assembly Trowel Pre-Set Up InstructionsSeat Assembly Battery SetupHTN-SERIES Initial START-UP Engine Oil Level Always check engine oil Before Each USEGearbox Oil Level Fuel Gauge Important Information Before You Start HTN-SERIES OperationSteering HTN-SERIES OperationMaintenance Schedule HTN-SERIES MaintenanceHTN-SERIES Maintenance Air Cleaner DailyReinstall the air cleaner cover and secure the latches Disassembly and Reassembly Standard Type Air Cleaner Components to CheckMake sure the cooling shrouds are reinstalled Make sure the correct depth airOil Filter 100 Hours Changing Engine Oil And FilterFuel Filter 200 Hours Oil And Fuel LinesChecking The Drive Belt Removing the Drive BeltHave a 3/4 X 1 X 3-1/4 inch wooden block available Reinstall the spare belt carrier and the drive belt guard HTN-SERIES- MaintenanceInstalling the Drive Belt Using Replacement Drive Belt Wooden BlockSpare Drive Belt Replacement HTN-SERIES- MaintenanceTorque Converter/Variable Pitch Pulley Drive Pulley Drive System Theory of OperationClutch How It Works Figure Condition a z Engine IdlingBlade Pitch Matching Blade Pitch for Both Sets of BladesStabilizer Ring Removal Trowel Arm adjustment ProcedureRemove the trowel arm from the spider plate Trowel Arm RemovalTrowel Blade Removal Spider Plate Hex Head Bolt Zerk FittingTrowel Arm Adjustment Checking Trowel Arm StraightnessSideview Re-Assembly Trowel Arm Adjustment SetupDecommissioning Trowel/Components Installing Pans Onto Finisher BladesSymptom Possible Problem Solution HTN-SERIES -TROUBLESHOOTING Engine HTN-SERIES-TROUBLESHOOTING Trowel Troubleshooting HTN-SERIES-TROUBLESHOOTING TrowelHTN-SERIES Notes Payment Terms Page Mexico United Kingdom United StatesCanada Brazil Your Local Dealer is

HTN-27K-TCSL specifications

The Multiquip HTN-27K-TCSL is a cutting-edge piece of technology designed for professionals in the construction and industrial sectors. This portable hydraulic power unit is known for its robust performance and versatility, making it an ideal choice for a wide range of applications.

One of the standout features of the HTN-27K-TCSL is its powerful engine. Equipped with a reliable 27-horsepower Kohler engine, this unit ensures maximum efficiency and performance, allowing operators to complete tasks quickly and effectively. The engine is designed to be both fuel-efficient and environmentally friendly, adhering to emission regulations without sacrificing power.

The HTN-27K-TCSL boasts a unique hydraulic system that delivers high-pressure flow rates, making it suitable for operating multiple tools simultaneously. With a maximum hydraulic pressure of 3,000 PSI, this power unit can effortlessly handle demanding tasks such as concrete breaking, water jetting, and other heavy-duty applications. The ability to provide consistent hydraulic power allows for enhanced productivity on job sites.

In terms of versatility, the Multiquip HTN-27K-TCSL is equipped with a wide range of output options. Its hydraulic outlet configurations can support various attachments, enabling users to adapt the unit for diverse tasks. This flexibility makes it an invaluable tool for contractors, landscapers, and utility companies.

Another notable characteristic of the HTN-27K-TCSL is its rugged construction. Built to withstand the rigors of tough job sites, this hydraulic power unit features a durable frame and protective covers that shield the engine and components from dust and debris. The compact design ensures easy transportation and maneuverability, making it a practical choice for both indoor and outdoor use.

Additionally, the HTN-27K-TCSL is designed with operator safety in mind. It features a user-friendly interface, with clearly labeled controls for easy operation. Safety features such as emergency shut-off switches and protective guards further enhance its usability, ensuring that operators can work confidently.

In summary, the Multiquip HTN-27K-TCSL is a powerful, versatile, and robust hydraulic power unit designed to meet the demanding needs of various industries. With its exceptional performance, durable construction, and focus on safety, it continues to be a trusted choice among professionals seeking reliable hydraulic solutions.
Top Page Image Contents