Falcon U108610-07 1 -2, 3, 4, An oven light is not working, The oven door is misaligned

Page 18

Fig.6-1

Fig.6-1

Fig.6-2

ArtNo.324-0007 Unscrewing the bulb cover

Fig.6-3

Eect of hinge adjustment – exaggerated for clarity

Fig.6-4	Centre line of hinge pin

An oven light is not working

The bulb has probably burnt out. You can buy a replacement bulb (which is not covered under the warranty) from a good electrical shop. Ask for a 15W – 230V lamp, FOR OVENS. It must be a special bulb, heat resistant to 300 °C (Fig.6-1).

Turn o the power at the circuit breaker.

Before removing the existing bulb, turn o the power supply and make sure that the oven is cool. Open the oven door and remove the oven shelves.

Unscrew the bulb cover by turning counter-clockwise. It may be very sti (Fig.6-2). Taking care to protect your ngers with a glove in case the bulb should shatter.

Screw in the new bulb; screw back the bulb cover. Turn on the circuit breaker and check that the bulb now lights.

The oven door is misaligned

The bottom hinge of either oven door can be adjusted to alter the angle of the door (Fig.6-3). Loosen the bottom hinge xing screws and use the notch and a at bladed screwdriver to move the position of the hinge to set the hinge position (Fig.6-4).

Retighten the hinge screws.

ArtNo.320-0007 Oven door hinge adjustment 2

Oven door omitted for clarity

16

Image 18

Contents 90 Dual Fuel Installation InstructionsUser Guide U108610-07Contents surfaces To avoid overheating, DO NOT install the cooker 1. Before You StartWARNING The appliance and its accessible parts nnDO NOT use a steam cleaner to clean the cookerand ammable liquids a safe distance away from your cooker nnThis appliance is heavy so take care when moving itAlways keep combustible materials, e.g. curtains DO NOT store ammable materials in the storageA B C D 2. Cooker OverviewHotplate Burners Fig.2-1Fig.2-5 Fig.2-6 Wok BurnerFig.2-3 Fig.2-4 Fig.2-7designed to t in any of the other pan supports Fig.2-12 DO NOT put it crossways - it will not t properly andwill be unstable DO NOT put it on any other burner - it is not Always leave space around the griddle for the gasesFig.2-15 nnNever close the grill door when the grill is onArtNo.210-0001 Classic grill control Fig.2-16Minute Minder Setting the Time of DayA B C D E F To Stop the Ovens AutomaticallyFig.2-30Fig.2-31 AUTO is Showing, But you Want to Reset to Manual CookingKey Lock Fig.2-32The Handyrack Main Oven Oven Shelves - Left-hand Main OvenOven Shelves - Right-hand Tall Oven Fig.2-35DO NOT use the timed oven if the adjoining oven is Tips on Cooking with the TimerGeneral Oven Tips already warm4. Cooking Table The Single Ring Burners 5. Cleaning Your CookerDO NOT mix dierent cleaning products - they may The Wok BurnerDO NOT use harsh abrasive cleaners or sharp metal ‘Cook & Clean’ PanelsBefore you remove any of the grill parts for cleaning Do not use steel wool, oven cleaning pads, or anyHotplate Recommended Cleaning MethodRemoving the Main Oven Linings PartWhat cleaning materials are recommended for the cooker? 6. TroubleshootingHotplate ignition or hotplate burners faulty Never use caustic or abrasive cleaners as these willFig.6-4 Fig.6-1 Fig.6-2Fig.6-3 An oven light is not workingOut of Warranty 7. InstallationIf you Have a Problem INSTALLATIONAS 5601 - ‘Gas Installations’ Installer’s Name Installer’s Company Installer’s Telephone NumberRead the instructions before installing or using this appliance Failure to install the appliance correctly couldYou will also need the following tools Checking the Parts3. Side Clearances - Measurement D & E 1. Overhead - Measurement A2. Side Clearances - Measurements B & C Fig.7-1On no account try and move the cooker while it is Lowering the Two Rear RollersCompleting the Move plugged into the electricity supplyFitting a Stability Bracket Unless properly installed, the cooker could be tipped byFitting the Stability Bracket and Chain Fitting the Restraining ChainNatural Gas Pressure TestingGas Connection PropaneFig.7-10 Fixed WiringA N Fig.7-11Oven Check Hotplate CheckGrill Check Fitting the Handles and Handrail Classic onlyClassic - Removing the Control Panel 8. Conversion to LP GasWhen servicing or replacing gas-carrying Toledo - Removing the Control PanelFig.8-4 1.2 To Remove the Side Panels 9. Servicing1.1 To Remove the Control Panel WARNING - SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON2.3 To Change a Hotplate Burner Injector 2.1 To Remove the Hotplate2.2 To Replace the Hotplate Control Taps 2.4 To Replace a Hotplate Burner Electrode3.3 To Change the Ignition Generator 3.1. To Replace the Ignition or Light Switch3.2 To Replace the Clock 4.1 To Replace the Grill Controller5.5 To Replace an Oven Thermostat 5.3 To Change the Oven Element5.4 To Change an Oven Element Thermal Cut-out Fig.9-4 Fig.9-56.1 To Remove the Grill Door 6.3 To Adjust the Main Oven Door Angle6.6 To Adjust the Main Oven Door Catch Keep 6.2 To Replace the Main Oven Door6.9 To Replace the Tall Oven Door Magnetic Latch 6.7 To Remove the Tall Oven Door6.8 To Replace the Tall Oven Door Outer Panel 6.10 To Change an Oven Door Seal10. Circuit Diagram DescriptionColour Usable volume litres 11. Technical DataMaximum power output @ 230V 50 Hz COUNTRY OF DESTINATION AustraliaPage Page Clarence Street, Royal Leamington Spa Warwickshire, CV31 2AD, England Tel +44 0 1926 457400 Fax +44 0 1926E-mail consumers@falconappliances.co.uk