Acclaim Lighting 2490 installation instructions Fireplace Installations, 6mm

Page 11

5.Secure the extension plate and flue collar with the fasteners removed in the first step. Run the bolts in only finger-tight. Adjust the fit of the extension plate and/or flue collar if necessary. Tighten all four (4) fasteners, but do not overtighten them. Test the ac- tion of the griddle; make any needed adjustments by loosening the hardware, repositioning the flue collar and extension plate, retesting the griddle action, and retightening the hardware.

Fireplace Installations

A fireplace installation requires special clearance be- tween the side of the stove and the right and left walls, the side of the stove and the decorative side trim on the fireplace face, and the top of the stove and the mantel.

Ventilated shields (noncombustible) installed on non- combustible spacers 1” (25 mm) away from the com- bustible surface may be used to reduce clearances.

(Fig. 14) A mantel shield for the Resolute Acclaim must be at least 48” (1219 mm) long, centered over the stove. Side trim shields must extend the full length of the trim. (Fig. 15)

Mantel

Spacer

1" (25mm)

Shield

1/4" (6mm)

ST501

Fig. 14 A custom-formed mantel shield.

An unprotected mantel (“A”,Fig. 15) must have a mini- mum clearance of 36” (914mm), measured from the stove’s top plate. With a ventilated shield the clearance may safely be reduced to 30” (762 mm). Maximum depth of the mantel is 9” (229 mm).

Unprotected top trim (B) protruding 1¹⁄" (38 mm) or less from the face of the fireplace must be a minimum of 28" (711 mm) from the stove's top surface. This clearance may not be reduced by shielding. If top trim protrudes more than 1¹⁄" (38 mm) the mantel clearances of 36" (915mm) unshielded and 30" (762 mm) shielded must be used.

Resolute® Acclaim Woodburning Stove

Side trim must have a minimum clearance of 8" (203 mm), measured from the stove's top side edge. In this case, ventilated shielding will not provide protection to allow clearance reduction.

In addition, a fireplace installation must observe the floor protection guidelines discussed previously.

The charts and sample installations on the following pages list the clearances required for various installa- tion configurations of the Resolute Acclaim.

 

A

B

 

 

C

 

C

Fireplace Mantel and Trim Clearances

Measured from the stove top and sides

 

Protected

Unprotected

A. Mantel

30” (762 mm)

36” (914 mm)

B. Top Trim

28” (711 mm)

28” (711 mm)

C. Side Trim

8” (203 mm)

8” (203 mm) ST253b

Fig. 15 Maintain clearances to combustible components of the mantelpiece.

2000893

11

Image 11
Contents Resolute Acclaim Introduction Table of ContentsAccessories Resolute Acclaim Model SpecificationsMasonry Chimneys InstallationWhat Kind of Chimney to Use Chimney Size Chimney Connector GuidelinesDouble-wall Chimney Connectors Prefabricated ChimneysFreestanding Installations Single-wall Chimney ConnectorsSecuring the Single-wall Connector To a Masonry Chimney Wall Pass-Throughs Above a FireplaceThrough a Fireplace An approved wall pass-through for the United States Floor Protection Floor Protection for Fireplace InstallationReversing the Flue Collar Keep the Stove a Safe Distance From Surrounding MaterialsSafe Ways to Reduce Clearances Wall Shields6mm Fireplace InstallationsFront Clearance To Combustibles Resolute Acclaim Clearance ChartParallel Installation Corner Stove Clearance Chimney Connector ClearanceTop Exit, No Heat Shields Stove Installed Stove in Corner Parallel to WallMinimum Wall Shield Requirements for Common Installations Corner Parallel Installations Construction Requirements Alcove InstallationsTwo Controls Operate the Stove Install Stove LegsOperation Unpack the StoveBurn Only High-Quality Fuel Use the Air Control Settings That Work Best for YouRemovable Andirons For Greater Front-Loading Convenience Two Rules For SuccessStarting and Maintaining a Wood Fire Primary Air SettingsHow to Build and Sustain a Wood Fire Air Setting Air Control PositionSurface Thermometer is a Guide to Performance Reloading and Reviving a Wood FireRemove and Store Ash Safely Rules for Open Fire ViewingClear the Ash Frequently Draft Management Back-puffing Draft TestingCreosote FuelCare of the Cast Iron Surface MaintenanceCleaning the Glass Clean the Exhaust ChannelsAvoid Damaging the Glass Adjust the DoorAdjust the Damper as Needed Repair Missing Cement in SeamsResolute Acclaim Gaskets on Moving Parts How to Replace GasketsReplace Broken Glass Immediately Replace Broken Firebricks Gaskets on Resolute Acclaim Stationary PartsReplacing the Door Gaskets Replacing the Griddle GasketTwo Months Resolute Acclaim Maintenance ScheduleYearly Spring Cleaning DailyItem Description Part Number Resolute Acclaim Woodburning StoveAshlip Door Leg Resolute Acclaim Woodburning StoveWarranty Mhsc

2490 specifications

Acclaim Lighting has made a significant impact in the world of architectural and entertainment lighting with innovative solutions that cater to a wide array of applications. One of their standout products is the Acclaim Lighting 2490, a lighting fixture that exemplifies cutting-edge technology and high performance.

The Acclaim Lighting 2490 is primarily designed for use in both indoor and outdoor settings. Its robust construction ensures durability against various weather conditions, making it an ideal choice for architectural lighting, theatrical productions, and even large-scale events. One of the standout features of the 2490 is its high lumen output, allowing it to provide bright, effective illumination in any scenario.

Equipped with advanced LED technology, the 2490 offers exceptional energy efficiency without compromising brightness. The fixture utilizes high-quality LEDs that not only extend the lifespan of the unit but also minimize heat generation, making it a sustainable choice for long-term use. This energy-efficient operation translates to lower energy costs and reduced environmental impact.

The Acclaim Lighting 2490 boasts versatile color rendering, with RGBW capabilities that allow users to create a wide palette of colors. This feature is particularly beneficial for event lighting and architectural applications where mood and aesthetics play a crucial role. Additionally, the fixture supports DMX control, making it easy to integrate into existing lighting setups and enabling synchronized light shows or dynamic lighting transitions.

Another noteworthy characteristic of the 2490 is its adjustable beam angle. This adaptability provides users with the flexibility to focus light where it's needed most, whether for highlighting architectural features or creating immersive environments for theatrical performances.

Built with user-friendliness in mind, the Acclaim Lighting 2490 includes options for easy mounting and installation. Its lightweight design coupled with intuitive controls ensures that both professional lighting technicians and newcomers can operate it with ease.

Overall, the Acclaim Lighting 2490 stands as a testament to the brand's commitment to quality and innovation in lighting technology. With its combination of efficiency, versatility, and durability, it offers a comprehensive solution for a wide array of lighting needs, making it a preferred choice among lighting designers and professionals alike.